eHome EH100 User manual

2eHome EH100 User Manual
Table of Contents
Product Overview ........................................................4
Package Contents....................................................4
System Requirements ............................................. 4
Introduction..............................................................5
Features...................................................................6
Hardware Overview .................................................7
Connections.......................................................7
LEDs ..................................................................8
Installation....................................................................9
Before you Begin .....................................................9
Wireless Installation Considerations...................... 10
Connect to Cable/DSL/Satellite Modem ................11
Connect to Another Router....................................12
Configuration............................................................. 14
Web-based Configuration Utility ............................ 14
Setup Wizards..................................................16
Internet Connection Wizard..........................16
Wireless Security Wizard ............................. 22
Manual Internet Setup .....................................25
Internet Connection Setup ............................... 26
Dynamic IP (Cable) ...................................... 26
PPPoE (DSL) ...............................................27
PPTP............................................................28
L2TP.............................................................29
Big Pond....................................................... 31
Static (assigned by ISP)...............................32
Wireless Settings ............................................. 34
Wireless Network Settings ...........................35
Network Settings.............................................. 36
Router Settings ............................................ 37
DHCP Server Settings .................................38
Advanced...............................................................39
Port Forwarding ...............................................39
Application Rules ............................................. 41
Network Filters................................................. 43
Website Filters .................................................45
Firewall Settings...............................................46
Advanced Wireless Settings ............................ 48
Advanced Network Settings.............................50
Tools ......................................................................52
Administrator Settings...................................... 52
Administrator Password:...............................53
Remote Management:..................................53
Time Settings................................................... 54
System Settings............................................... 55
Update Firmware .............................................56
System Check.................................................. 57
Status.....................................................................58
Device Info ....................................................... 58
Table of Contents

3eHome EH100 User Manual
Table of Contents
Log................................................................... 59
Stats................................................................. 60
Wireless Stats.................................................. 61
Support .................................................................. 62
Wireless Security.......................................................63
What is WEP?........................................................ 63
Configure WEP ......................................................64
What is WPA? ........................................................66
Configure WPA-PSK ..............................................67
Configure WPA (RADIUS)...................................... 68
Connect to a Wireless Network ................................ 69
Using Windows®XP............................................... 69
Configure WEP ......................................................70
Configure WPA-PSK ..............................................72
Troubleshooting.........................................................74
Wireless Basics ......................................................... 78
What is Wireless? ..................................................79
Tips........................................................................ 81
Wireless Modes ..................................................... 82
Networking Basics .................................................... 83
Check your IP address ..........................................83
Statically Assign an IP address ............................. 84
Technical Specifications........................................... 85
Contacting Technical Support.................................. 87
Warranty .....................................................................88

4eHome EH100 User Manual
Section 1 - Product Overview
• eHome EH100 Wireless G Broadband Router
• Power Adapter
• Ethernet Cable
• Manual and Warranty on CD
System Requirements
• Ethernet-based Cable or DSL Modem
• Computers with Windows®, Macintosh®, or Linux-based operating systems with an installed Ethernet
adapter
• Internet Explorer Version 6.0 or Netscape Navigator Version 6.0 and Above (for configuration)
Product Overview
Package Contents
Note: Using a power supply with a different voltage rating than the one included
with the EH100 will cause damage and void the warranty for this product.

5eHome EH100 User Manual
Section 1 - Product Overview
Introduction
The eHome Wireless G EH100 Router is capable of transferring data with a maximum wireless signal rate of up to
54Mbps* in the 2.4GHz frequency — the same wireless frequency as 802.11b. The eHome EH100 Wireless Router
also offers four Ethernet ports to support multiple computers.
The advanced wireless technology built into the EH100 Wireless Router offers data transfer speeds with a maximum
wireless signal rate of up to 54Mbps* through its wireless channels allowing streaming videos and other high bandwidth
applications, such as online gaming events, to operate without the hassle of Ethernet cables. The ability to use high
bandwidth applications also makes streaming real-time programs more enjoyable and more efficient.
With the EH100 Wireless Router’s built-in advanced firewall, threats of hackers penetrating your network are minimized.
Some firewall features include functions that allow or disallow certain ports to be open for certain applications. Time
scheduling can be established as a firewall rule so that specific ports will be open at certain times and be closed at
other times. Features like MAC filtering, URL blocking, and domain blocking are useful tools to prevent other unwanted
intruders from connecting to your network or browsing restricted sites.
The easy-to-use configuration wizard takes only minutes to setup and guides users step-by-step through configuring
the EH100. With all the versatile features and an user-friendly utility, the EH100 Wireless Router provides an enhanced
networking experience.
* Maximum wireless signal rate derived from IEEE Standard 802.11g specifications. Actual data throughput will vary. Network conditions and
environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput
rate. Environmental conditions will adversely affect wireless signal range.

6eHome EH100 User Manual
Section 1 - Product Overview
• Faster Wireless Networking - The EH100 provides up to 54Mbps* wireless connection with other
802.11g wireless clients. This capability allows users to participate in real-time activities online, such as
video streaming, online gaming, and real-time audio. The performance of this 802.11g wireless router
gives you the freedom of wireless networking at speeds 5x faster than 802.11b.
• Compatible with 802.11b and 802.11g Devices - The EH100 is still fully compatible with the IEEE
802.11b standard, so it can connect with existing 802.11b PCI, USB and Cardbus adapters.
• Advanced Firewall Features - The Web-based user interface displays a number of advanced network
management features including:
• Content Filtering - Easily applied content filtering based on MAC Address, IP Address, URL,
and/or Domain Name.
• Filter Scheduling - These filters can be scheduled to be active on certain days or for a
duration of hours or minutes.
• Secure Multiple/Concurrent Sessions - The EH100 can pass through VPN sessions. It
supports multiple and concurrent IPSec and PPTP sessions, so users behind the EH100 can
securely access corporate networks.
• User-friendly Setup Wizard - Through its easy-to-use Web-based user interface, the EH100 lets you
control what information is accessible to those on the wireless network, whether from the Internet or from
your company’s server. Configure your router to your specific settings within minutes.
* Maximum wireless signal rate derived from IEEE Standard 802.11g specifications. Actual data throughput will vary. Network conditions and
environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput
rate. Environmental conditions will adversely affect wireless signal range.
Features

7eHome EH100 User Manual
Section 1 - Product Overview
Hardware Overview
Connections
Pressing the Reset Button restores
the router to its original factory
default settings.
Receptor for the Power Adapter.
The Auto MDI/MDIX WAN
port is the connection for
the Ethernet cable to the
Cable or DSL modem.
LAN Ports
Connect Ethernet devices such as
computers, switches, and hubs.

8eHome EH100 User Manual
Section 1 - Product Overview
Hardware Overview
LEDs
WAN LED
A solid light indicates connection
on the WAN port. This LED blinks
during data transmission.
WLAN LED
A solid light indicates that the wireless
segment is ready. This LED blinks during
wireless data transmission.
Local Network LEDs
A solid light indicates a connection to an
Ethernet-enabled computer on ports 1-4.
This LED blinks during data transmission.
Status LED
A blinking light indicates that the
EH100 is ready.
Power LED
A solid light indicates a proper
connection to the power supply.

9eHome EH100 User Manual
Section 2 - Installation
Before you Begin
Installation
This section will walk you through the installation process. Placement of the router is very important. Do not place the
router in an enclosed area such as a closet, cabinet, or in the attic or garage.
Please configure the router with the computer that was last connected directly to your modem. Also, you can only use
the Ethernet port on your modem. If you were using the USB connection before using the router, then you must turn off
your modem, disconnect the USB cable and connect an Ethernet cable to the WAN port on the router, and then turn
the modem back on. In some cases, you may need to call your ISP to change connection types (USB to Ethernet).
If you have DSL and are connecting via PPPoE, make sure you disable or uninstall any PPPoE software such as
WinPoet, Broadjump, or Enternet 300 from your computer or you will not be able to connect to the Internet.

10eHome EH100 User Manual
Section 2 - Installation
Wireless Installation Considerations
The eHome wireless router lets you access your network using a wireless connection from virtually anywhere within
the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls,
ceilings, or other objects that the wireless signals must pass through, may limit the range.Typical ranges vary depending
on the types of materials and background RF (radio frequency) noise in your home or business. The key to maximizing
wireless range is to follow these basic guidelines:
1. Keep the number of walls and ceilings between the eHome router and other network devices to a
minimum - each wall or ceiling can reduce your adapter’s range from 3-90 feet (1-30 meters.) Position
your devices so that the number of walls or ceilings is minimized.
2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a
45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet
(14 meters) thick! Position devices so that the signal will travel straight through a wall or ceiling (instead
of at an angle) for better reception.
3. Building Materials make a difference. A solid metal door or aluminum studs may have a negative effect on
range. Try to position access points, wireless routers, and computers so that the signal passes through
drywall or open doorways. Materials and objects such as glass, steel, metal, walls with insulation, water
(fish tanks), mirrors, file cabinets, brick, and concrete will degrade your wireless signal.
4. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that
generate RF noise.
5. If you are using 2.4GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and
home security systems), your wireless connection may degrade dramatically or drop completely. Make
sure your 2.4GHz phone base is as far away from your wireless devices as possible. The base transmits
a signal even if the phone in not in use.

11eHome EH100 User Manual
Section 2 - Installation
If you are connecting the router to a cable/DSL/satellite modem, please follow the steps below:
1. Place the router in an open and central location. Do not plug the power adapter into the router.
2. Turn the power off on your modem. If there is no on/off switch, then unplug the modem’s power adapter. Shut down
your computer.
3. Unplug the Ethernet cable (that connects your computer to your modem) from your computer and place it into the
WAN port on the router.
4. Plug an Ethernet cable into one of the four LAN ports on the router. Plug the other end into the Ethernet port on your
computer.
5. Turn on or plug in your modem. Wait for the modem to boot (about 30 seconds).
6. Plug the power adapter to the router and connect to an outlet or power strip. Wait about 30 seconds for the router
to boot.
7. Turn on your computer.
8. Verify the link lights on the router. The power light, WAN light, and the LAN light (the port that your computer is
plugged into) should be lit. If not, make sure your computer, modem, and router are powered on and verify the cable
connections are correct.
9. Skip to page 14 to configure your router.
Connect to Cable/DSL/Satellite Modem

12eHome EH100 User Manual
Section 2 - Installation
If you are connecting the eHome router to another router to use as a wireless access point and/or switch, you will have
to do the following before connecting the router to your network:
• Disable UPnP™
• Disable DHCP
• Change the LAN IP address to an available address on your network.The LAN ports on the router cannot
accept a DHCP address from your other router.
To connect to another router, please follow the steps below:
1. Plug the power into the router. Connect one of your computers to the router (LAN port) using an Ethernet cable.
Make sure your IP address on the computer is 192.168.0.xxx (where xxx is between 2 and 254). Please see the
Networking Basics section for more information. If you need to change the settings, write down your existing settings
before making any changes. In most cases, your computer should be set to receive an IP address automatically in
which case you will not have to do anything to your computer.
2. Open a web browser and enter http://192.168.0.1 and press Enter. When the login window appears, set the user
name to admin and leave the password box empty. Click OK to continue.
3. Browse to the Advanced > Advanced Network page. Uncheck the box next to Enable UPnP. Click the Save
Settings button to continue.
4. Browse to the Setup > Network Settings page. Uncheck the box next to Enable DHCP Server.
5. Under Router Settings, enter an available IP address and the subnet mask of your network. Click Save Settings
to save your settings. Use this new IP address to access the configuration utility of the router in the future. Close the
browser and change your computer’s IP settings back to the original values as in Step 1.
Connect to Another Router

13eHome EH100 User Manual
Section 2 - Installation
6. Disconnect the Ethernet cable from the router and reconnect your computer to your network.
7. Connect an Ethernet cable in one of the LAN ports of the router and connect it to your other router. Do not plug
anything into the WAN port of the eHome router.
8. You may now use the other 3 LAN ports to connect other Ethernet devices and computers.To configure your wireless
network, open a web browser and enter the IP address you assigned to the router. Refer to the Configuration and
Wireless Security sections for more information on setting up your wireless network.

14eHome EH100 User Manual
Section 3 - Configuration
Configuration
This section will show you how to configure your new eHome wireless router using the web-based configuration
utility.
Web-based Configuration Utility
To access the configuration utility, open a web-browser
such as Internet Explorer and enter the IP address of
the router (192.168.0.1).
Enter the user name (admin) and your password. Leave
the password blank by default.
If you get a “Page Cannot be Displayed” error, please
refer to the Troubleshooting section for assistance.

15eHome EH100 User Manual
Section 3 - Configuration
After logging in the Setup page will be displayed:

16eHome EH100 User Manual
Section 3 - Configuration
Setup Wizards
Setup Wizards are available to quickly and easily configure basic router settings. Click Setup Wizard to access the
wizards.
Click Launch Internet Connection Setup Wizard.
Internet Connection Wizard

17eHome EH100 User Manual
Section 3 - Configuration
Click Next to continue.
Create a new password and then click Next to continue.
Select your time zone from the drop-down menu and then
click Next to continue.

18eHome EH100 User Manual
Section 3 - Configuration
If you selected Dynamic, you may need to enter the MAC
address of the computer that was last connected directly
to your modem. If you are currently using that computer,
click Clone Your PC’s MAC Address and then click Next
to continue.
The Host Name is optional but may be required by some
ISPs.The default host name is the device name of the Router
and may be changed.
Select the type of Internet connection you use and then
click Next to continue.

19eHome EH100 User Manual
Section 3 - Configuration
If you selected PPPoE, enter your PPPoE username and
password. Click Next to continue.
Select Static if your ISP assigned you the IP address, subnet
mask, gateway, and DNS server addresses.
Note: Make sure to remove your PPPoE software from your
computer. The software is no longer needed and will not
work through a router.
If you selected PPTP, enter your PPTP username and
password. Click Next to continue.

20eHome EH100 User Manual
Section 3 - Configuration
If you selected L2TP, enter your L2TP username and
password. Click Next to continue.
If you selected Static, enter your network settings supplied
by your Internet provider. Click Next to continue.