TRENDnet TEW-411BRP User manual

User’s Guide
0
TEW-411BRP
Wireless 802.11g AP Router
User’s Manual
Version 1.4

User’s Guide
1

User’s Guide
2
Copyright Statement
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical,
photocopying, recording, or otherwise without the prior writing of the publisher.
July. 2003

User’s Guide
3
Contents
1. Introduction.............................................................................................................. 4
2. Safety Notification ................................................................................................... 5
3. Hardware Installation .............................................................................................. 6
4 Web Management Settings ...................................................................................... 7
4.1. Primary Setup….. ……………………………………………………………………………………….8
4.2. Security …………………………………………………………………………………………………..13
4.3. System ……………………………………………………………………………………………………15
4.4. DHCP Server …….……………………………………………………………………………………..18
4.5. SNMP Info ……………………………………………………………………………………………….20
4.6. Status …………………………………………………………………………………………………….21
4.7. Advanced Wireless …………………………………………………………………………………...23
4.8. Access Filters …………………………………………………………………………………………..26
4.9. Virtual Server …………..……………………………………………………………………………….29
4.10. Routing Table …………………………………………………………………………………………31
4.11. Dynamic DNS ……………….………………………………………………………………………..33
5 . Troubleshooting.................................................................................................... 34

User’s Guide
4
1. Introduction
Thank you for purchasing your AP Router Wireless 802.11g AP Router.
This user guide will assist you with the installation procedure.
The package you have received should contain the following items:
 AP Router Wireless 802.11g AP Router
 User Guide
 Power Supply / Cord
 Ethernet Cable
Note: if anything is missing, please contact your vendor

User’s Guide
5
2. Safety Notification
Your Wireless AP Router should be placed in a safe and secure location. To ensure proper operation,
please keep the unit away from water and other damaging elements. Please read the user manual
thoroughly before you install the device. The device should only be repaired by authorized and
qualified personnel.
 Please do not try to open or repair the device yourself.
 Do not place the device in a damp or humid location, i.e. a bathroom.
 The device should be placed in a sheltered and non-slip location within a temperature range of
+5 to +40 Celsius degree.
 Please do not expose the device to direct sunlight or other heat sources. The housing and
electronic components may be damaged by direct sunlight or heat sources.

User’s Guide
6
3. Hardware Installation
Front Panel
The front panel provides LED’s for device status. Refer to the following table for the meaning of each
feature.
LED STATUS Description
Off No power
Red On
1. Power on 2. Reset to default 3. Firmware upgrade (first 1
minute)
PWR/STAT
Red Blink
1. System up 2. Power on 3. Firmware upgrade
Off no Ethernet link detected
Green On
10/100Mbps Fast Ethernet link detected. No activity.
LAN
Green
Blink Indicates data traffic on the 10/100 Mbps LAN
WAN Orange
Blink Indicates data traffic on the 10/100 Mbps LAN
G Yellow
Blink
Indicates the device is linking or active data through wireless
links
Rear Panel
The rear panel features 4 LAN ports, 1 WAN port and Reset button. Refer to the following table for the
meaning of each feature.
Power (DC 5v)
Used to connect to the power outlet. Only use the power
adapter provided with the device. Use of an unauthorized
power adapter may cause damage to your device and
violate your warranty.
Reset
Press the Reset Button for approximately ten seconds, all
configurations will set to factory default settings.
LAN The RJ-
45 Ethernet ports used to connect your PC, hub,
switch or Ethernet network.
WAN The RJ-
45 Ethernet port labeled WAN is used to connect
your AP Router to your xDSL or Cable modem.
AP Router Default Settings
The default settings are shown following.
User
Password admin
AP Router IP
Address 192.168.1.1
AP Router Subnet
Mask 255.255.255.0
RF ESSID wlan-g
11g RF Channel 6
Mode 11b+11g
Encryption Disabled
DHCP client Enabled

User’s Guide
7
4 Web Management Settings
START UP & LOGIN
In order to configure the Wireless 11g AP Router, you must use your web browser and manually input
http://192.168.1.1 into the Address box and press Enter. The Main Page will appear.
In order to configure the Wireless 11g AP Router, you must input the password into the Password box
and leave blank on the User Name box. The default password is “admin”.
Once you have logged-in as administrator, it is a good idea to change the administrator password to
ensure a secure protection to the Wireless 11g AP Router. The Security Settings section described
later in this manual describes how to change the password.
Once you have input the correct password and logged-in, the screen will change to the Setup page
screen.
TURN ON POWER SUPPLY
Quick power cycle can caused system corruption. When power on, be careful not to shut down in
about 5 seconds, because data is writing to the flash.

User’s Guide
8
4.1. Primary Setup
Primary Setup
This screen contains all of the Router's basic setup functions.
.
Most users will be able to configure the AP Router and get it working properly using the settings on
this screen. Some Internet Service Providers (ISPs) will require that you enter AP Router Wireless
802.11g AP Router specific information, such as User Name, Password, IP Address, Default Gateway
Address, or DNS IP Address. This information can be obtained from your ISP, if required.
WAN:
MAKE CORRECT NETWORK SETTINGS OF YOUR COMPUTER
To change the configuration, use Internet Explorer (IE) or Netscape Communicator to
connect the
WEB management 192.168.1.1.

User’s Guide
9
Host Name: This entry is necessary for some ISPs and can be provided by them.
Domain Name: This entry is necessary for some ISPs and can be provided by them.
Configuration Type: The Router supports four connection types:
Dynamic IP Setting
Static IP Address
PPPoE (Point-to-Point Protocol over Ethernet)
PPTP (Point-to-Point Tunneling Protocol)
These types can be selected from the drop-down menu next to Internet Connection. The information
required and available features will differ depending on what kind of connection type you select.
Some descriptions of this information are included here:
Internet IP Address and Subnet Mask
This is the Router's IP Address and Subnet Mask as seen by external users on the
Internet (including your ISP). If your Internet connection requires a static IP address,
then your ISP will provide you with a Static IP Address and Subnet Mask.
• Default Gateway
Your ISP will provide you with the Gateway IP Address.
• DNS (Domain Name Server) IP Address
Your ISP will provide you with at least one DNS IP Address.
• User Name and Password
Enter the User Name and Password you use when logging onto your ISP through a
PPPoE or PPTP connection.
• Connect on Demand
You can configure the Router to disconnect your Internet connection after a specified
period of inactivity (Max Idle Time). If your Internet connection has been terminated due
to inactivity, Connect on Demand enables the Router to automatically re-establish your
connection as soon as you attempt to access the Internet again. If you wish to activate
Connect on Demand, click the radio button.
If you want your Internet connection to remain active at all times, enter 0 in the AP
Router 802.11g AP Router max Idle Time field. Otherwise, enter the number of minutes
you want to have elapsed before your Internet connection terminates.
• Keep Alive Option
This option keeps you connected to the Internet indefinitely, even when your connection
sits idle. To use this option, click the radio button next to Keep Alive. The default Redial