Eiki V-2300 Setup guide

EIKI VISUAL SYSTEM PRESENTER
V-2300
OWNER’S INSTRUCTION MANUAL
EIKI INDUSTRIAL CO., LTD.

WARNING
To reduce the risk of fire or electric shock, do not expose this unit to
rain or moisture.
The lighting flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated dangerous voltage’
within the unit’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons
.
The exclamation point within a quilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the unit.
IMPORTANT SAFEGUARDS
1. Read Instructions - All the safety and operating instructions should be read before
the unit is operated.
2. Retain Instructions - The safety and operating instructions should be retained for
future reference.
3. Heed Warnings - All warnings on the unit and in the operating instructions should
be adhered to.
4. Follow Instructions - All operating and use instructions should be followed.
5. Cleaning - Unplug this unit from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6. Attachments - Do not use attachments not recommended by the unit manufacturer
as they may cause hazards.
7. Water and Moisture - Do not use this unit near water - for example, near a bath tub,
wash bowl, kitchen sink, or laundry tub: in a wet basement: or near a swimming
pool; and the like.

8. Accessories - Do not place this unit on an unstable can, stand, tripod, bracket, or
table. The unit may fall, causing serious injury to a child or adult, and serious
damage to the unit. Use only with a can, stand, tripod, bracket, or table
recommended by the manufacturer’s instructions, and should use a mounting
accessory recommended by the manufacturer,
9. A unit and ca~ combination should be moved with care. Quick stops, excessive
force, and uneven surfaces may cause the unit and cart combination to overturn.
10. Ventilation - Slots and openings in the unit are provided for ventilation and to
ensure reliable operation of the unit and to protect it from overheating, and these
openings must not be blocked or covered. The openings should never be blocked by
placing the unit on a bed, sofa, rug, or other simillar surface. This unit should not be
placed in a built-in installation such as a bookcase or rack unless proper ventilation
is provided or the manufacturer’s instructions have been adhere to.
11. Power Sources - This unit should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power supply to
your home, consult your product dealer or local power company.
12. Grounding polarization - This unit may be equipped with a three-wire grounding-
type plug, a play having a third(grounding) pin. This plug will only fit into a
grounding-type power outlet. This is a safety features. If you are unable to insert the
plug into the outlet, contact your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the grounding-type plug.
13. Power-Cord protection - Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience receptacles, and the point where
they exit from the unit.
14. Lighting - For added protection for this unit during a lighting storm, or when it is
left unattended and unused for long periods of time, unplug it from the wall outlet
and disconnect cable system. this will prevent damage to the unit due to lighting and
power-line surges.

15. Overloading - Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or electric shock,
16. Object and Liquid Entry - Never push objects of any kind into this unit through
openings as they may touch dangerous voltage points or shod-out pads that could
result in a fire or electric shock. Never spill liquid of any kind on the unit.
17. Servicing - Do not attempt to service this unit yourself as opening or removing
covers may expose you to dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
18. Damage Requiring Service - Unplug this unit from the wall outlet and refer
servicing to qualified service personnel under the following conditions.
a) When the power-supply cord or plug is damaged.
b) If liquid has been spilled, or objects have fallen into the unit.
c) If the unit has been exposed to rain or water.
d) If the unit does not operate normally by following the operating instructions,
Adjust only these controls that are covered by the operating instructions as an
improper adjustment of other controls may result in damage and will often
require extensive work by a qualified technician to restore the unit to its normal
operation.
e) If the unit has been dropped or damaged in any way.
f) When the unit exhibits a distinct change in performance - this indicates a need for
service.
19. Replacement pans - When replacement pans are required, be sure the service
technician has used replacement pans specified by the manufacturer or have the
same characteristics as the original pan. Unauthorized substitutions may result in
fire, electric shock, or other hazards.
20. Safety Check - Upon completion of any service or repairs to this unit. ask the
service technician to perform safety checks to determine that the unit is in proper
operating condition.
21. Heat - The unit should be situated away from heat sources such as radiators, heat
registers, stoves, or other products (including amplifiers) that produce heat.
SAVE THESE INSTRUCTIONS

TABLE OF CONTENTS
1. DESCRIPTION AND CONTROLS . 2-3
2. SETTING-UP REMOTE CONTROL UNIT 4
3. ORERATION OF REMOTE CONTROL 5
4. SETTING-UP THE UNIT 6
5. HOW TO CONNECT TO A TV MONITOR AND EXTERNAL EQUIPMENT 7
6. HOW TO USE AUTO FOCUS 8
7. HOW TO DISPLAY 9
8. TROUBLESHOOTING 9
9. SPECIFICATIONS 10-11

1. CAMERA HEAD
Rotate to shoot the printed material and three-dimensional objects in shooting area and to shoot
the distance objects.
2. REMOTE CONTROL STORAGE
Remote control unit works also when seating in the remote control storage.
3. S-VIDEO OUTPUT JACK
Used to connect TV monitor or VCR with S-VIDEO input jack.
4. VIDEO OUTPUT JACK (2)
Used to connect TV monitor or VCR with video input jack.
NOTE : S-VIDEO AND VIDEO signal are output simultaneously and the unit can be connected to
TV monitor with S-VIDEO input jack and VIDEO input jack respectively.
5. DC POWER INPUT JACK
Used to connect DC plug of AC adapter.
6. CONVERSION LENS
Remove this lens to shoot the distance objects.
7. IR RECEIVER
8. MAIN BODY
9. LEG STOPPER
10. LEG
11. SHOOTING AREA

To insure safe operation, please observe the following precautions
• Use(2)AA type batteries.
• Do not use different type batteries and a new and with a used battery.
• Do not discharge and disassemble a battery.
• Be sure the battery polarity should be set properly and do not contact anode and cathode
terminal.
• Remove the batteries fro the compartment when the unit is not used.
• If the batteries have leaked on the remote control, carefully wipe the case clean and install new
batteries.
The maximum operating range for the remote control is about 5m, 60 for the front of unit
CAUTION
• Avoid sun light and strong light from the lighting equipment.
• Avoid contact with water.
• Do not drop and give strong impact the remote control unit.
• Avoid heat and humidity.

CAUTION
Disconnect power for setting up the unit.
1. Remove two legs from Leg stopper.
2. Spread two legs to the set up position.
3. Lift up the legs to the set up position.
4. Rotate Camera head until Lens is aiming just below.
5
. Remove a Remote control unit.( it also works while it
is seated in the Remote Control storage.

CONNECT THE UNIT AND TV MONITOR WITH VIDEO CABLES
SUPPLIED AS STANDARD ACCESSORIES.
1. Video output jack of the unit connected to video input jack (S-VIDEO or VIDEO) of TV monitor
with video cable.
2 . How to use S-VIDEO output jack.
S-VIDEO and VIDEO signal are output simultaneously and the unit can be connected to a TV
monitor with S-VIDEO input jack and VIDEO input jack respectively. S-VIDEO cables may be
obtained locally.

There are three kinds of auto focus mode
(1) One-Shot Auto Focus Mode
This mode is to fix the focus just once when an image is set up on screen, so it is proper for the
still material or object.
(2) Auto Focus Mode
This mode is to let focusing meet each image, so it is proper for the moving material or when
materials are changed frequently.
(3) Electric Focus Mode
This mode is to move lens by FOCUS switch and get focusing.
When FOCUS switch is operated, One-Shot Auto Focus Mode and Auto Focus Mode are
released, and change to Electric Focus Mode.
And if either ZOOM switch or AUTO switch is operated, it changed to One-Shot Auto Focus.
A. One-Shot AUTO Focus
When power on the unit, LED of POSI switch lights, and LED of AUTO lights on and off at the first
setting up. When LED of AUTO goes out, it is ready for One-Shot Auto Focus Mode.
1. When zooming is set up to position, One-Shot Auto Focus works to get focus.
2. When out of focus, push AUTO switch once, and adjust focusing.
B. Change to Auto Focus Mode
1. Pushing AUTO switch about 3 seconds until LED of AUTO switch starts to light on and off, and
stop pushing the switch after LED of AUTO will light. Now Auto Focus works.
2. By pushing buttons other than [POSI/NEGA] , Auto Focus mode is canceled.
C. Change to Electric Focus Mode
1. When three-dimensional object with different height is displayed but focus is not obtained properly,
then push FOCUS
+ or - switch to change Electric Focus Mode so as to adjust focusing.
2 . By pushing buttons other than [ZOOM] or [AUTO] , this mode is changed to [One-Shot Auto Focus
mode].

A. When displaying printed material.
1. Connect power of the unit. Blue back image appears on the monitor and then image of the printed
material will be displayed.
2. Put the printed material below the lens and operate Zoom switch watching TV monitor according
to the size of the material. (if focus is out after zooming operation, push AUTO FOCUS switch
once. If the correct focus is not obtained yet, push Focus switch to adjust focusing manually.)
B. When displaying three-dimensional object.
Caution
When displaying shooting area without conversion lens, focus may not work to get focus.
When displaying the shooting area, conversion lens is necessary to be installed.
SYMPTOM CAUSE REMEDY
No Power Plug not connected to outlet
No good connection of AC
Adaptor
Connect plug to outlet
Connect AC Adaptor right
No Image Power is OFF
Poor connection of video cable
Connect plug to outlet
Connect video cable right
Focus is Out Subject is too close to lens Subject should not come up
more than 100mm above stage
surface
Dark Image No good Bright adjustment Adjust Brightness by remote
control

Lens f=5.4-64.Smm(F1 .8-2.7)+conversion lens
shooting Area (*1) 320x236mm(Max,) *1
28 X 21 mm(Min.)
Zooming (12X)electric power zoom lens
Focusing Auto/One-shot_Auto/Power
Iris auto
TV system NTSC PAL
Image pick-up element 1/3 Inch CCD
All picture element 818HX508V 795HX596V
Effective picture element 768H X494V 752H X 582V
Synchronization Internal
Horizontal Resolution 460 TV Lines 450 TV Lines
S/N ratio more than 48dB
C-Video 1.OVp-p/75Ω
S-Video Y=1.OVp-p/75Ω
Video output level
C=0.286Vp-p/75ΩC=~300Vp-p/75Ω
White balance Auto INDOOR / OUTDOOR
Shutter speed 1/60 sec
(switchable to 1/100 sec)
1/50 sec
(switchable to 1/100 sec)
.
Brightness Adjustment (*2) Yes
Default Yes(to reset normal_adjustment preset by factory)
Input terminal DC power input(EIAJ φ2.1mm)X1
Output terminal Video output (RCA PIN jack/75 Ωunbalance) X 2
S-Video output (mini Din 4pin 75Ωunbalanced

Power supply AC Adaptor DC 6.5V (as standard Acc.)
Power consumption 3W
Dimensions 350(W) X 275(D) X 463(H)mm(SET-U P)
130(W)X500(D)X85(H)mm(FOLDED)
Weight 1.5Kg
Standard accessories Power cord Owners manual, Remote control unit
A/V Cable, AC Adaptor
Operation Temperature 5
o
C - 40
o
C
Operation Humidity 20% - 80% (no condensation)
*1 Shooting area will get a little bit smaller than 320X236mm when monitoring at overscanning.
*2 *1All functions can be controled only by the remote control unit.

EIKI INDUSTRIAL CO., LTD.
4-12 Banzai-cho Kita-ku OSAKA, JAPAN
Tel:6-63I l-9479~Fax:6-63l 1-8486
EIKI INTERNATIONAL, INC.
26794 Vista Terrace Drive,
Lake Forest, CA92630-8! 13 U.S.A
Tel :[phone]• Fax:[phone]
EIKI INTERNATIONAL,INC.CANADA BR.
P.O. BOX 156 310 First Street Unit 2 Midland. Ontario. L4R 4K8 Canada
Tel:[phone]• Fax:[phone]
EIKI DEUTSCHLAND GmbH
AM Frauwald 1265510 Jdstein
TeI:6126-9371-0•Fax:6l26-937I-l I
EIKI CZECH spols.r.o .
Umelecka 15.17000
Praha 7 Holesovice
Tel:2-2057 l4l3~Fax:2-2057l4l I