eInfochips OpenRD-Client User manual

Page | 1
OpenRD-Base: Quick Start Guide
Designed for Marvell®by eInfochips
QUICK START GUIDE
Thank you for purchasing the OpenRD-Client. The OpenRD-Client uses a
Marvell®88F6281 SoC, which is based on an embedded 1.2 GHz Sheeva™
CPU, equipped with 256 KB L2 cache, 512 MB FLASH and 512 MB DRAM.
Thank you for purchasing the OpenRD-Base. The OpenRD-Base uses a Marvell®
88F6281 SoC, which is based on an embedded 1.2 GHz Sheeva™ CPU, equipped with
256 KB L2 cache, 512 MB FLASH and 512 MB DRAM.
The board supports Linux 2.6.22.18 and UBIFS file system and features 2
Gigabit Ethernet ports, 7 USB 2.0 ports, SATA, eSATA, SD Card, UART, SDIO,
SMBus, TDM (Optional header), Mini USB and JTAG port for debugging. In
addition, the OpenRD-Client extends its capabilities with a 2D-GPU (Graphics
Processing Unit) with a VGA Connector and Audio In/Out ports.

Page | 2
OpenRD-Base: Quick Start Guide
Designed for Marvell®by eInfochips
Shipping Contents
1. OpenRD- Client Board
2. Power Adapter
3. Cables – USB, Cat5/6
4. CD/DVD (Contains documentation and Installation files)
•Quick Start Guide
•User Guide
•Product Brief
•openrd-devkit-v1.0
Before You Begin
Before you start, please make sure you have the following items
•OpenRD-Client board, Power Adapter, USB Cable, CAT 5/6 Cable, CD/DVD
•One VGA display/LCD monitor
Installation Steps
1. Please connect cables (Cat 5/6 cable, USB Mini B, Serial – RS232, RS485, VGA
Cable etc.) to the board as per your application requirements
2. Connect supplied power adapter to the board
3. Apply power to the board
Successful Power On
Following is a screen snapshot of a successful power on, provided that you have
connected the monitor to the board.
If the serial connection is done as per the steps mentioned in user guide, then you
should see following screen shot of POST test immediately after power on.

Page | 3
OpenRD-Base: Quick Start Guide
Designed for Marvell®by eInfochips
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: OpenRD-Client LE
U-Boot 1.1.4 (Apr 24 2009 - 13:56:42) Marvell version: 3.4.16
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CEE80
Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM CS[1] base 0x10000000 size 256MB
DRAM Total size 512MB 16bit width
Flash: 0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
Checking for BootROM Routine Errors
No. of BootROM routine retries: 8
NAND: Nand ECC error
Running POST...
DDR2 data bus test PASSED
DDR2 address bus test PASSED
UART 1 internal loopback test on baudrate 9600 PASSED
UART 1 internal loopback test on baudrate 19200 PASSED
UART 1 internal loopback test on baudrate 115200 PASSED
Device: 0, Size: 512 MB, Page Size: 2 KB, Block Size: 128 KB
NAND detection test PASSED
Bad Block: 15820000
Bad Block: 1b760000
Bad Block: 1dcc0000
NAND bad-block detection test PASSED
RTC test PASSED
6/6 tests PASSED
POST com
p
leted

Page | 4
OpenRD-Base: Quick Start Guide
Designed for Marvell®by eInfochips
Introduction to IO Ports of OpenRD-Client Board
USB Mini B Connection: Connect mini B end of
the ‘USB mini B to Type A’ cable to the USB
mini B connector of the OpenRD-Client
SD Card Connection:
Insert the SD Card in the
slot. It is possible to run applications from SD
Card. It can also be used as local storage of
data.
RS485 Connection: Provides RS485
connectivity. Connect RJ45 Cable as shown in
picture
RS232 Connection:
This connector is UART1
Port, which provides Serial Connectivity.
Connect NULL modem Female RS232 cable as
shown in figure.
Audio In/Out:
Connect Audio Input and Audio
Output cable as shown in picture
VGA Connection:
Connect one end of Male
VGA cable to the connector as shown in picture
and another end to VGA display/monitor.

Page | 5
OpenRD-Base: Quick Start Guide
Designed for Marvell®by eInfochips
Additional Information
Please refer to OpenRD-Client User Guide
http://www.marvell.com/ & http://www.einfochips.com/marvell
USB Connection: Connect the USB device to
the USB port, located on the front panel of the
OpenRD-Client board. It is possible to run
applications from USB storage device. It can also
be used as local storage of data.
Ethernet Connection:
Connect CAT5/CAT6
cable to GbE0/GbE1 port of the board.
eSATA Connection:
Connect eSATA cable to
the eSATA connector
SMBus Connection: Connect SMBus Cable to
the SMBus Connector.
Power Connection:
Connect the power supply
to the DC power input connector located in the
front panel of the OpenRD-Client board and
connect the other end to your local power outlet.