EisSound KBSOUND 60201 User manual

ENG User Manual

SOUNDAROUND Controller User Manual ENG
FCC compliance information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
This product does not contain any user serviceable components. Any unaothorized product changes or modifications will invalidate
warranty and all applicable regulatory certifications and approvals, including authority to operate this device.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected to.
- Consult the dealer or an experienced radio/TV technician for help.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended
operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as fas as
possible from the user body or set the device to lower output power if such function is available.
Industry Canada notice
This equipment complies with Canadian RSS-210. This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR-210 d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Caution: (i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference
to co-channel mobile satellite systems; (ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-
5725 MHz shall comply with the e.i.r.p. limit; and (iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz
shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate. (iv) Users should also
be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850
MHz and that these radars could cause interference and/or damage to LE-LAN devices.
Avertissement: Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des instructions précises sur les restrictions
susmentionnées, notamment : (i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour une
utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes
canaux; (ii) le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et 5 470-5 725 MHz doit se
conformer à la limite de p.i.r.e.; (iii) le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz) doit se
conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point, selon le cas. (iv) De plus, les utilisateurs
devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils
ont la priorité) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des
dommages aux dispositifs LAN-EL.
The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended
operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as
possible from the user body or set the device to lower output power if such function is available.

SOUNDAROUND Controller User Manual ENG
7. Only use attachments/accessories specified
by the manufacturer.
8. Operate this product only from the type of power
source indicated on the back panel.
9. Keep this product a safe distance away from naked
flame, such as a lit candle.
10. When replacement parts are required, be sure your
technical service used replacement parts specified
by the manufacturer or have the same features as
the original part. Unauthorized substitutions may
result in fire, electric shock or other damages.
11. The recommended operating temperature range
is from 5ºC to 40ºC (41ºF – 104ºF).
12. WARNING: Although the product is in OFF mode
it is connected to the mains.
Important Safety Instructions
1. Please read, keep and follow these instructions.
2. Heed all warnings.
3. WARNING: To reduce the risk of fire or electric
shock, do not expose this apparatus to rain or
moisture. This product is not an outdoor product.
It is only for indoor use.
4. Clean only with a dry cloth.
5. Do not block any ventilation openings or the port
hole at the rear side of the product. Install in
accordance with the manufacturer’s instructions.
6. Do not install near any heat sources
such as radiators, heat registers, stoves,
or other apparatus (including amplifiers)
that produce heat.
RISK OF
ELECTRIC SHOCK
DO NOT OPEN
CAUTION
This equipment is a Class II or
double insulated Electrical
appliance. It has been
designed in such away that it
does not require a safety
connection to electrical earth.
DISPOSAL
This product can be recycled. Products bearing this symbol must NOT be thrown away with normal household waste. At the end of the product’s life, take it
to a collection point designated for recycling of electrical and electronic devices. Find out more about return and collection points through your local authority.
The European Waste Electrical and Electronic Equipment (WEEE) Directive was implemented to dramatically reduce the amount of waste going to landfills,
thereby reducing the environmental impact on the planet and on human health. Please act responsibly by recycling used products. If this product is still
useable, consider giving it away or selling it.

SOUNDAROUND Controller User Manual ENG
POWERED BY
CC-1203-01
64460130
Our Wi-Fi SOUNDAROUND range comprises the In Wall Wi-Fi SOUNDAROUND Controller,
together with our standalone SOUNDAROUND Wi-Fi Speakers SA 30W & SA 50W.
The In Wall Wi-Fi SOUNDAROUND Controller is focused on the building industry and for
installation purposes. The standalone SOUNDAROUND Wi-Fi Speakers SA 30W & SA 50W
are complementary and portable products that co-exist with the In Wall Controller.

SOUNDAROUND Controller User Manual ENG
1. Keypad Description 6
2. Installation and power requirements 6
3. Led Display 11
4. Setup 12
4.1 Minimum requirements 12
4.2 Download the App 12
4.3 Connecting your SOUNDAROUND Controller to a Wi-Fi network 13
4.3.1 Web Browser Method 13
4.3.2 WPS Button Method 15
4.3.3 Via App 15
4.3.4 Ethernet hardwired connection 17
5. Play Music 17
5.1 Wi-Fi Mode 17
5.2 Bluetooth Mode 20
5.3 Audio- In Mode 21
6. Settings 23
7. FAQ’s 25
8. Specifications 28

6
ENG
SOUNDAROUND Controller User Manual
AUDIO-IN
AUDIO-IN
4”
WPS
1. Keypad Description
2. Installation and power requirements
FRONT PANEL
AUDIO-IN
JACK INPUT
MUTE
KEY
VENTILATION
GRILL
WPS BUTTON
WIFI KEY
BLUETOOTH KEY
VOLUME KEYS
In Wall Wi-Fi SOUNDAROUND Controller
(The Controller)
Power supply
8 Ohm speaker
The Controller is
mounted in a EISSOUND
wallbox (Ref. 18214)
125 x 75 x 35 mm
(4,92 x 2,95 x 1,37 ins)
Basic Installation
1
1
2
2
3
3
AUDIO-IN
AUDIO-IN
4”
WPS
˜ 120V/230V
GND
VCD L+R-R+
L-
V-V+
V+
V-
AC/N AC/L

7
ENG
SOUNDAROUND Controller User Manual
Power Requirements
The Controller is powered from an external power supply unit. Any 24Vdc, 15Vdc, 12Vdc
power supply may be used depending on the audio output needed and the number of
Controllers installed.
OUTPUT AUDIO POWER
Speaker Impedance
4 ohms 8 ohms 16 ohms
Power 24Vdc ---- 25+25W 15+15W
Supply 15Vdc 16+16W 10+10W 5,5+5,5W
Voltage 12Vdc 10+10W 6+6W 3,5+3,5W
CONSUMPTION
Speaker Impedance
4 ohms 8 ohms 16 ohms
Power 24Vdc ---- 60W 44W
Supply 15Vdc 45W 27W 18W
Voltage 12Vdc 30W 18W 14W
2.1 INSTALLATION GUIDE
2.1.1 Advice
It is recommended to place the router in a place where the Wi-Fi signal will be equally
distributed throughout the home or installation.
Beware of the following physical obstacles when placing the Controllers and the other
wireless devices, such as the router. Some surfaces may absorb the Wi-Fi signal and cause
signal loss and unwanted behavior.

8
ENG
SOUNDAROUND Controller User Manual
MATERIAL INTERFERENCE LEVEL
Wood Low
Synthetic Low
Glass Low
Water Medium
Brick Medium
Marble Medium
Plaster High
Reinforced cement High
Metal Very High
Wireless interference occurs when two or more wireless devices compete for the same
Wi-Fi band, which can lead to performance problems. Be aware if any of the following
devices are installed in the same area as the Controllers and router and keep them as far
as possible (minimum distance between each other of 50cm): 2.4 GHz or DECT cordless
phones, wireless video transmitters that operate on the 2.4GHz or 5GHz Wi-Fi band,
microwaves, wireless security cameras, wireless access points and extenders, 2.4 GHz
baby monitors, garage door opener devices, wireless photo frames…
Router minimum requirements: Router Wi-Fi 802.11n with WPA2-PSK (AES) encryption,
5GHz highly recommended.
Smartphone/tablet minimum requirements: ANDROID 4.1 / iOS 7.0 and later.
2.1.2 Controller location
Choose the correct location for the Controllers. Take care about
the installation recommendations above.

9
ENG
SOUNDAROUND Controller User Manual
140mm.
125mm.
75mm.
81,5mm.
Install the EISSOUND in-wall box (Ref. 18214) or make a cavity with
the following dimensions.
2.1.3 Wiring
Insert in the box the wires of the power supply unit, speaker cables and,
optionally, the Ethernet cable. For the best performance of the system we
recommend the option with the Ethernet hardwired connection.
In-wall Box Electronic Module Frame
Depth: 35mm.

10
ENG
SOUNDAROUND Controller User Manual
2.1.4 Connection and switches setup
 •Connect the wires to the Controller Terminals.
 •Connect the Ethernet connector to the Controller if applicable.
 •Select the switches to choose the volume level audio output (maximum, medium, low)
and the mono/stereo sound output.
2.1.5 Installing the Controller
Insert the Controller in the wall and secure with screws.
Fix the frame to the Controller.
Take care about the position of
the frame: the ventilation holes must
be at the bottom, NOT at the top
(the frame has one unique position).
BACK PANEL
ETHERNET
RJ45 connector
SWITCH
PROGRAMMING
Max Volume
Mid Volume
Low Volume
Stereo
Mono
TERMINALS
VDC = DC power input (12-24 Vdc)
GND = Ground
R+ / R- = Right Speaker Output
L+ / L- = Left Speaker Output
VENTILATION HOLES
On
On
On
On
On
3
3
3
3
3
2
2
2
2
2
1
1
1
1
1

11
ENG
SOUNDAROUND Controller User Manual
2.1.6 Power-on
Turn on the power supply unit. The 3 leds will flash simultaneously for 40”. Wait until Wi-Fi
led flashes in white.
2.1.7 Network Setup
To setup the Controller to the network, follow the steps in chapter 4.
3. Led Display
Music Options
MODE LED REBOOTING STATUS
Wi-Fi
White flashing slowly Rebooting (40”) Searching Wi-Fi network
White flashing fast Wi-Fi connection in process
White ON Wi-Fi connected (audio OFF)
Green ON SPOTIFY Streaming
Blue ON Wi-Fi streaming (audio ON)
BT
Blue flashing slowly Rebooting (40”) Waiting connection with BT
device previously paired (60”)
Blue flashing fast BT pairing process
Blue ON BT connected
AUDIO-IN
Red flashing slowly Rebooting (40”)
Red ON AUDIO-IN activated
(audio ON)

12
ENG
SOUNDAROUND Controller User Manual
General LED Status
Standby: All leds will go OFF after 2 minutes of inactivity.
Vol - / + : Led flashes with volume increase / decrease.
Reset to Factory default: All leds flash simultaneously (white, blue and red).
Firmware updated: The Wi-Fi led flashes in different colors.
Mute: The led flashes slowly. Audio is muted but streaming continues to be received.
4. Setup
4.1 MINIMUM REQUIREMENTS
 •Wi-Fi Router 802.11n, with WPA2-PSK encryption (AES).
 •For Multiroom we recommend a 5 GHz multimedia router (speed> 600 Mbps).
 •For best operation, the router should be placed at the center of the home or installation.
 •Smartphone/Tablet requirements: ANDROID 4.1 minimum, iOS 7.0 minimum
4.2 DOWNLOAD THE APP
ANDROID USERS
Tap the Google Play Store on the
ANDROID Device to download
the ALLPLAY JUKEBOX APP
APPLE USERS
Tap the Apple App Store on the
iOS Device to download the
ALLPLAY JUKEBOX APP

13
ENG
SOUNDAROUND Controller User Manual
4.3 CONNECTING YOUR IN WALL WI-FI SOUNDAROUND
CONTROLLER TO A WI-FI NETWORK
4.3.1 Web Browser Method
To set up the Controller press the Wi-Fi key for 8”. Immediately the three leds will flash
simultaneously. Wait until the Wi-Fi led flashes slowly in white.
Go to the Wi-Fi settings in your smartphone/tablet and search for the S-AROUND IWW
(+ six characters, which are the Controller’s unique MAC address-hardware). You will
need to wait about 1 minute before the SOUNDAROUND Controller appears. Select the
Controller. The Wi-Fi led flashes fast to indicate that the Controller is waiting to setup the
network connection.
Automatically the smartphone/tablet default web browser launches and re-directs
to the login web page.
If it does not redirect automatically, then open a web browser on your smartphone/tablet
(safari, google chrome) and in the search bar enter the following IP Address number:
172.19.42.1 Press enter.
You will then
be requested
to name your
Controller e.g.
Kitchen, Bedroom,
Gym… When
done, press next.
Now select your
Wi-Fi network
from the network
list, enter your
password, press
Next and then
Connect when
finished.
172.19.42.1
Next
Device Name
Please give your devide a name to identify it on the
network. Example: Kitchen, Bedroom.
powered by
*must be completed
*Devide Name S-AROUND IWW...
172.19.42.1
Next
Wireless Network Settings
Choose the wireless network you would like to use,
and enter a password if one is required.
powered by
*must be completed
*Network Name Workshop
*Password •••••••
Show Password
DHCP

14
ENG
SOUNDAROUND Controller User Manual
When connected to your network
the Wi-Fi Led on the Controller will turn
ON in white. The smartphone/tablet
will automatically disconnect from the
Controller and reconnect with your
previous network connection.
172.19.42.1
Connecting
Connecting, please wait...
powered by
172.19.42.1
You’re connected!
Your network connection may be lost shortly.
Please make sure that you have the Qualcomm®
AllPlayTM Jukebox app installed on your mobile
device to begin streaming music.
powered by
Note: : If your network router does not assign an IP address automatically, switch the
DHCP function to OFF and then enter the IP address manually. Then enter the network
key again if required, and press “CONNECT”.
The Controller saves the connection and it will not be necessary to setup the connection
again. It will connect automatically.

15
ENG
SOUNDAROUND Controller User Manual
4.3.2 WPS Button Method
Please check beforehand that your router has a WPS key function.
To set up the Controller press the Wi-Fi key for 8”. Immediately the three leds will flash
simultaneously. Wait until the Wi-Fi led flashes slowly in white.
• Press the WPS button in the front of the Controller by inserting a non-metallic
sharp object into the WPS hole. The Wi-Fi led flashes fast to indicate that the
Controller is waiting to setup the network connection.
• Press the WPS button on your Wi-Fi Router. Connection should be automatic but
you can refer to the LED indication chart above if you are unsure.
• When connected to your network the Wi-Fi Led on the Controller will turn ON
in white.
• The Controller will appear with the factory default identier
(SOUNDAROUND CONTROLLER). To personalize the name open the settings
menu on your App.
4.3.3 App Method
For iOS Users
Not applicable.
For ANDROID Users
Press the Wi-Fi key for 8” on the Controller. Immediately the three leds will flash
simultaneously and wait until the Wi-Fi led flashes slowly in white.

16
ENG
SOUNDAROUND Controller User Manual
Open the ALLPLAY JUKEBOX app and go to the “Select a player” menu
list and Press the “+” button to add the Controller to the network.
Open the App and
go to the “Select a
player” list.
Select your Wi-Fi
network in the
network list and
enter your password.
Select Next.
Name your
controller.
Cancel
Pause All
Select a P... +
No AllPlay players
found.
Next
Wi-Fi Network
Select your Wi-Fi
network
JAZZTEL_VCPj
WPA2_CCMP
Show password
AllPlay Players
Please select one player to
set up.
S-AROUND IWW af1edf_AJ
Connecting to player...
Choose Name
Please choose or enter a
name for your player
Living Room
Bedroom
Kitchen
Ofce
Patio
Custom Name
Press the “+” button
to add one Controller

17
ENG
SOUNDAROUND Controller User Manual
4.3.4 Ethernet hardwired connection
If your Controller has a wired network once you set up your router the Wi-Fi Led on
the Controller will turn ON in white.
• The controller will appear with the factory default identier
(SOUNDAROUND CONTROLLER). To personalize the name open the settings
menu on your App.
5. Play Music
5.1 WI-FI MODE
The Controller is automatically in Wi-Fi mode and the Wi-Fi led is ON in white. To select the
Wi-Fi mode press the Wi-Fi key on the front panel of your Controller.
Open the ALLPLAY JUKEBOX App in your smartphone/tablet, after a few seconds you will
see the list of the Controllers you have already set up (Living room, Bedroom, kitchen, Gym
or, whatever).
Select the room/area to which you want to stream music. The App will open the menu to
select the music sources. In Wi-Fi mode the options are:
A. Music on the device
B. Music on the network
C. Music services
Make sure your smartphone/tablet, audio devices and the Controllers are all connected
to the same Wi-Fi network.

18
ENG
SOUNDAROUND Controller User Manual
A. Music on the Device
Play music that is stored on your device.
B. Music on the Network
The App locates the DLNA servers connected to your home network. It can be a NAS
(network attached storage), a computer with DLNA server function (windows 7 and above).
There are various DLNA server software for Windows and OSX, for example Serviio, Plex,
EyeConnect, DivxPlayer.
C. Music Services
Play Music via an alternative App. Your Controller and the ALLPLAY JUKEBOX allow you
to stream on-line music like Spotify, Rhapsody, Napster and more. Open the Music Service
tab, select and open the App and play the music. You may need to be registered and for
certain Apps such as Spotify Premium fees may apply. If you use Sportify the led will be
ON in green.
• Internet Radio: One of the featured Apps is Qualcomm® AllPlay™ Radio, powered
by Tunein Radio. This App allows you to listen to more than 100,000 internet radio
stations worldwide.
Warning: The Apps contained in Music Services (such as Spotify) run on different releases
from different operating systems, using different devices from different brands. As a result,
their functioning may present some differences between devices with the Jukebox App.
5.1.1 Play Music Options In Wi-Fi Mode
The App offers the following options:
5.1.2 Party Mode
Several smartphones/tablets can play and add music tracks to a shared playlist which
is then played in a specific room/area (Controller) or in the rooms/areas that have been
grouped together. (see Multiroom mode).

19
ENG
SOUNDAROUND Controller User Manual
5.1.3 Multiuser - Multizone Mode
A user can play different music tracks simultaneously in different rooms/areas (Controllers)
from the same smartphone/tablet.
Several smartphones/tablets (users) can play and add music tracks simultaneously
in different rooms/areas (Controllers).
5.1.4 Multiroom Mode
Multiroom mode means you have more than one room/area (several Controllers)
and they are grouped together.
Notes:
1. All Controllers and/or Speakers must be connected to the same Wi-Fi network.
2. The speed of the network is very important to ensure the Multi-room mode. If more than
two Controllers are grouped, we recommend the use of a 5GHz multimedia router.
To create a group, open the App and go to the “Select a Player” screen. Press the “Group”
button on the room/area with which you want to create the group. Select from the list the
rooms/areas you wish to group together and select done when finished. Once the group
is created play your music.
[Nothing Playing]
Group
[Nothing Playing]
Group
Don’t Stop Me Now - Queen
Select a Player
Pause All
Group
Bedroom
Kitchen
Dining Room
Bedroom
Select the players that will play Don’t Stop Me Now
Group
Clear All Select All
Dining Room
Kitchen
Don’t Stop Me Now - Queen
Select a Player
Pause All
Bedroom
Dining Room Group

20
ENG
SOUNDAROUND Controller User Manual
5.2 Bluetooth Mode
The In Wall Wi-Fi SOUNDAROUND Controller includes a Bluetooth Audio Receiver that can
be connected to a Bluetooth compatible device (smartphone/tablet). Before commencing
any pairing process we recommend that you check that your Bluetooth device has A2DP/
AVRCP profiles. In addition, the pairing process can vary between manufacturers. Please
read carefully your Bluetooth device user manual beforehand. For a successful pairing
make sure the Bluetooth device is close to the Controller when performing this task.
To turn on the BLUETOOTH mode press the Bluetooth key for 4”. Once the blue led
flashes you are ready to pair. The Controller remains in pairing mode for one minute. If the
Bluetooth device is not connected during this time, the Controller will automatically return
to Wi-Fi mode and you must repeat the process.
Open the Bluetooth settings menu in your Bluetooth device (smartphone/tablet) and select
the Controller’s BLUETOOTH identifier (Same UNIQUE identifier previously set up for Wi-Fi
mode). This is the moment to pair. This step will only be necessary the first time for each
Bluetooth device.
Once the connection is established the blue led will stop flashing and remains ON while the
Bluetooth device is being used and within range of coverage (approx.10 meters/33 feet).
Now simply connect and play your music. Your DEVICE will control directly all features
such as choosing the song, play, pause, volume… not the JUKEBOX ALLPLAY App.
The Controller will revert to the Wi-Fi mode when the Bluetooth is disconnected or out
of range.
5.2.1. BLUETOOTH Re-streaming
Once your Bluetooth device is connected to the Controller you may take the advantage
of the Wi-Fi network and RE-STREAM the Bluetooth signal (your music) to other rooms/
areas connected to the same Wi-Fi network. This is a UNIQUE feature of the In Wall Wi-Fi
SOUNDAROUND Controller.