Eizo COLOREDGE CG2730 User manual

Important
Please read PRECAUTIONS, this User’s Manual, and the Setup Guide
(separate volume) carefully to familiarize yourself with safe and
effective usage.
• Please refer to the Setup Guide for basic information ranging from
connection of the monitor to a PC to using the monitor.
• The latest User’s Manual is available for download from our web site:
http://www.eizoglobal.com
Color Management LCD Monitor
User’s Manual

2
Location of Caution Statement
AVERTISSEMENT
WARNING
WARNUNG
This product has been adjusted specically for use in the region to which it was originally shipped. If
operated outside this region, the product may not perform as stated in the specications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information condential unless
prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every
effort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specications are subject to change without notice.

3
Notice for This Monitor
Notice for This Monitor
Aside from general purposes like creating documents and viewing multimedia content, this product is also
suited to applications such as creating images and graphics, and digital photo processing, where accurate
color reproduction is a priority.
This product has been adjusted specically for use in the region to which it was originally shipped. If the
product is used outside the region, it may not operate as specied in the specications.
This product may not be covered by warranty for uses other than those described in this manual.
The specications noted in this manual are only applicable when the following are used:
• Power cords provided with the product
• Signal cables specied by us
Only use optional products manufactured or specied by us with this product.
If you place this product on a lacquer-coated desk, the color may adhere to the bottom of the stand due to
the composition of the rubber. Check the desk surface before use.
It takes about 3 minutes (under our measurement conditions) for the performance of electrical parts to
stabilize. Please wait 30 minutes or more after the monitor power has been turned on, and then adjust the
monitor.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and
maintain a stable display.
When the screen image is changed after displaying the same image for extended periods of time, an
afterimage may appear. Use the screen saver or power save function to avoid displaying the same image for
extended periods of time.
If the monitor displays continuously over a long period of time, dark smudges or burn-in may appear. To
maximize the life of the monitor, we recommend the monitor be turned off periodically.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer
to “Cleaning” (page 4)).
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may
appear on the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994 % or higher.
The backlight of the LCD panel has a xed lifetime. When the screen becomes dark or begins to icker,
please contact your local EIZO representative.
Do not press on the panel or edge of the frame strongly, as this may result in display malfunctions, such
as interference patterns, etc. If pressure is continually applied to the panel, it may deteriorate or damage
your panel. (If the pressure marks remain on the panel, leave the monitor with a black or white screen. The
symptom may disappear.)
Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do
not attempt to brush with tissues as this may scratch the panel.

4Notice for This Monitor
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew
condensation may occur on the interior and exterior surfaces of the monitor. In that case, do not turn the
monitor on. Instead wait until the dew condensation disappears, otherwise it may cause some damage to
the monitor.
Cleaning
Attention
• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet
or panel, and also quality deterioration of the image.
• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel.
The stains on the cabinet and panel surface can be removed by using the provided ScreenCleaner.
To Use the Monitor Comfortably
• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor
according to the environmental conditions.
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.

5
Contents
Contents
Notice for This Monitor......................................... 3
Cleaning .................................................................... 4
To Use the Monitor Comfortably ............................ 4
Contents................................................................. 5
Chapter 1 Introduction....................................... 6
1-1. Features ......................................................... 6
1-2. Controls and Functions ............................... 8
●Front ................................................................ 8
●Rear ................................................................. 9
1-3. EIZO LCD Utility Disk...................................10
●Disk contents and software overview ............10
●To use ColorNavigator 6 ................................10
1-4. Compatible Resolutions .............................11
●DVI ..................................................................11
●DisplayPort .....................................................12
●HDMI ..............................................................13
1-5. Setting the Resolution ................................14
●Windows 10 ....................................................14
●Windows 8.1 / Windows 7 ..............................14
●OS X Mountain Lion (10.8) or later .................14
●Mac OS X 10.7 ...............................................14
Chapter 2 Basic Adjustments/Settings.......... 15
2-1. Switch Operation Method ...........................15
2-2. Switching Input Signals ..............................15
2-3. Switching the Display Mode
(color mode)..................................................16
●Display Modes ................................................16
2-4. Adjusting the Brightness............................16
Chapter 3 Advanced Adjustments/
Settings............................................ 17
3-1. Basic Operation of the Setting Menu ........17
3-2. Setting Menu Functions..............................19
●Color ...............................................................19
●SelfCalibration ................................................24
●Signal ............................................................ 27
●Preferences ................................................... 29
●Languages .................................................... 32
●Information .................................................... 32
Chapter 4 Administrator Settings................... 33
4-1. Basic Operation of the "Administrator
Settings" Menu............................................ 33
4-2. "Administrator Settings" Menu
Functions ..................................................... 34
Chapter 5 Troubleshooting.............................. 35
5-1. No Picture .................................................... 35
5-2. Imaging Problems....................................... 36
5-3. Other Problems............................................37
5-4. Built-in Calibration Sensor and
SelfCalibration Problems........................... 38
Chapter 6 Reference ........................................ 39
6-1. Attaching the Optional Arm....................... 39
6-2. Attaching/Detaching the Cable Holder .....41
6-3. Connecting Multiple External Devices..... 42
6-4. Making Use of USB
(Universal Serial Bus)................................. 43
●Required System Environment ..................... 43
●Connection Procedure (Setup of USB
Function) ........................................................ 44
6-5. Specications ............................................. 45
●Outside Dimensions .......................................47
●Main Default Settings .................................... 48
●Accessories ................................................... 48
Chapter 7 Glossary .......................................... 49
Appendix.............................................................. 51
Trademark ................................................................51
License / Copyright.................................................51
FCC Declaration of Conformity ............................ 52
LIMITED WARRANTY............................................. 53
Recycling Information ........................................... 54

6Chapter 1 Introduction
Chapter 1 Introduction
Thank you very much for choosing an EIZO color LCD monitor.
1-1. Features
• 27″ widescreen
• Wide color gamut display (Adobe® RGB coverage: 99 %)
• Achieves contrast ratio of 1500:1*1
A high contrast ratio allows for display of crisper black.
*1 Standard value. When "DUE Priority" is set to "Brightness"
• Resolution: Supports 2560×1440
• IPS panel with 178˚ horizontal and vertical wide viewing angles
• The monitor display stabilizes within approximately 3 minutes after the monitor is turned on.*2
*2 According to EIZO measurement conditions. However, if performing SelfCalibration (page 24),
it is necessary to wait at least 30 minutes after turning on the power, in order to obtain correct measurement
results.
• Frame synchronization mode supported (23.75 - 30.5 Hz, 47.5 - 61.0 Hz)
• Color mode function
Reproduces a color temperature, gamma, and gamut compliant with the following standards.
-Adobe®RGB / sRGB
See “Chapter 3 Advanced Adjustments/Settings” (page 17)
• This product is equipped with a built-in calibration sensor, and supports SelfCalibration in which the
monitor executes calibration independently.
See “SelfCalibration” (page 24)
• The provided Color Management Software "ColorNavigator 6" enables you to calibrate monitor
characteristics and generate color proles
See “1-3. EIZO LCD Utility Disk” (page 10)
• Equipped with a USB Hub function that supports USB 3.0
Achieves high-speed data transfers of up to 5 Gbps, which enables transfers of large amounts of data to and
from USB memory devices in a short amount time.
Also, the USB downstream port supports quick charging, so you can recharge your smartphone or
tablet in a short period of time.
See
“6-4. Making Use of USB (Universal Serial Bus)” (page 43) and “USB CHARGE Port” (page 30)
• Displays HDCP (High Bandwidth Digital Protection) protected content.

7
Chapter 1 Introduction
Attention
Be careful of the following points when using the built-in calibration sensor.
Do not touch the built-in calibration sensor.
It may reduce the measurement accuracy of the built-in calibration sensor, or result in injury
or equipment damage.
Attention
• A high temperature or high humidity environment may affect the measurement accuracy of the built-in
calibration sensor. We suggest storing and using the monitor under the following conditions.
- Temperature 30ºC or less
- Humidity 70 % or less
Avoid storing or using the sensor where it may be exposed to direct sunlight.
• Since the measurement result for the built-in sensor may be affected, ensure that the level of ambient light
that enters the receiver part of the built-in sensor does not change signicantly during measuring. Do not
touch the screen while measurement is in progress.
- The use of a monitor hood is recommended.
-While measuring, do not bring your face or any objects close to the monitor, do not look into the sensor.
- Set the monitor in the environment so that external light does not enter the sensor directly.
Note
• This monitor supports a portrait orientation display. When using the screen in a portrait position, you can
change the orientation of the Setting menu (see “Menu Rotation” (page 29)).
• When using the monitor screen in a portrait position, the graphics board supporting portrait display is
required. When placing the monitor in a portrait position, settings of your graphics board need to be
changed. Refer to the User’s Manual of the graphics board for details.

8Chapter 1 Introduction
1-2. Controls and Functions
●Front
1
3
2
1. Built-in calibration sensor Executes calibration for independent monitors.
“SelfCalibration” (page 24) (Self calibration)
Attention
• Do not touch the sensor as this will affect the measurement
accuracy.
2. Operation switches Displays menus. Operate the switches according to the operation
guide.
The switch indicator is lit white when you turn the power on.
3. Power switch Turns the power on or off.
The switch indicator is lit when you turn the power on. The indicator
color differs depending on the monitor's operation status.
White : Operating
Flashing white
(quickly twice)
: Indicates that recalibration is required if the
SelfCalibration schedule (page 25) is set.
Orange : Power saving mode
OFF : Power off
*1 See “3-1. Basic Operation of the Setting Menu” (page 17) for how to use.
Setting menu *1
Approx. 30°

9
Chapter 1 Introduction
●Rear
12
8
7654
11
9
10
4. Main power switch Turns the main power on or off.
: On : Off
5. Power connector Connects the power cord.
6. Input signal connectors Left: DVI-D connector
Center: HDMI connector
Right: DisplayPort connector
7. USB upstream port Connects to the USB cable when using software that requires a USB
connection, or when using the USB Hub function (page 43).
8. USB downstream port Connects to a peripheral USB device.
The port supports quick recharging (page 30).
9. Handle This handle is used for transportation.
Attention
• Firmly grasp and hold the monitor by the bottom while grabbing the
handle, and carefully convey the monitor so as not to drop it. Do not
hold the sensor section on the front side of the monitor.
10. Security lock slot Complies with Kensington’s MicroSaver security system.
11. Stand*2 Adjusts the height and angle (tilt and swivel) of the monitor.
Attention
• When adjusting the height or angle, do not hold the sensor section on
the front side of the monitor.
12. Cable holder *3 Covers the monitor cables.
*2 An optional arm (or an optional stand) can be attached by removing the stand section (see “6-1. Attaching
the Optional Arm” (page 39)).
*3 For details on mounting the cable holder, see “6-2. Attaching/Detaching the Cable Holder” (page 41).

10 Chapter 1 Introduction
1-3. EIZO LCD Utility Disk
An "EIZO LCD Utility Disk" (CD-ROM) is supplied with this product. The following table shows the disk
contents and an overview of the software programs.
●Disk contents and software overview
The disk includes application software programs for calibration, and the User's Manual. Refer to
“Readme.txt” or the “read me” le on the disk for software startup procedures or le reference
procedures.
Contents Overview
A "Readme.txt" or "read me" le
ColorNavigator 6 An application software for measuring and calibrating monitor characteristics and
generating ICC proles (for Windows) and Apple ColorSync proles (for Macintosh).
(The monitor and PC must be connected using the USB cable.)
User’s Manual of this monitor (PDF le)
●To use ColorNavigator 6
Refer to the User’s Manual on the CD-ROM disk for details on how to install and use the software.
When using this software, you will need to connect a PC to the monitor with the supplied USB cable.
For details on the USB cable connection, see (page 44).
Attention
• While using ColorNavigator 6, do not operate the power switch or operation switches on the front side on the
monitor.

11
Chapter 1 Introduction
1-4. Compatible Resolutions
The monitor supports the following resolutions.
●DVI
Resolution Dot
clock
Horizontal
scanning
frequency
Vertical
scanning
frequency
DVI
(Dual Link*1)
DVI
(Single Link*1)
640 x 480 25.175 MHz 31.469 kHz 59.940 Hz √ √
640 x 480 25.200 MHz 31.500 kHz 60.000 Hz √*3 √*3
720 x 400 28.322 MHz 31.469 kHz 70.087 Hz √ √
800 x 600 40.000 MHz 37.879 kHz 60.317 Hz √ √
1024 x 768 65.000 MHz 48.363 kHz 60.004 Hz √ √
1280 x 720p 74.250 MHz 37.500 kHz 50.000 Hz √*3 √*3
1280 x 720p 74.250 MHz 45.000 kHz 60.000 Hz √*3 √*3
1280 x 960 108.000 MHz 60.000 kHz 60.000 Hz √ √
1280 x 1024 108.000 MHz 63.981 kHz 60.020 Hz √ √
1600 x 1200 162.000 MHz 75.000 kHz 60.000 Hz √ √
1680 x 1050 119.000 MHz 64.674 kHz 59.883 Hz √*3 √*3
1680 x 1050 146.250 MHz 65.290 kHz 59.954 Hz √*3 √*3
1920 x 1080 138.500 MHz 66.587 kHz 59.934 Hz √ √
1920 x 1080p 74.250 MHz 27.000 kHz 24.000 Hz √*3 √*3
1920 x 1080p 74.250 MHz 28.125 kHz 25.000 Hz √*3 √*3
1920 x 1080p 74.250 MHz 33.750 kHz 30.000 Hz √*3 √*3
1920 x 1080p 148.500 MHz 56.250 kHz 50.000 Hz √*3 √*3
1920 x 1080p 148.500 MHz 67.500 kHz 60.000 Hz √ √
1920 x 1200 154.000 MHz 74.038 kHz 59.950 Hz √ √
2048 x 1080 74.250 MHz 27.000 kHz 24.000 Hz √*3 √*3
2560 x 1440*2 146.250 MHz 43.945 kHz 29.935 Hz - √
2560 x 1440*2 241.500 MHz 88.787 kHz 59.951 Hz √ -
*1 “Signal Format” (page 34) must be set.
*2 Recommended resolution
*3 The output device must be dened. Refer to the User’s Manual of the output device for further details.

12 Chapter 1 Introduction
●DisplayPort
Resolution Dot
clock
Horizontal
scanning
frequency
Vertical scanning
frequency DisplayPort
640 x 480 25.175 MHz 31.469 kHz 59.940 Hz √
640 x 480 25.200 MHz 31.500 kHz 60.000 Hz √*2
720 x 400 28.322 MHz 31.469 kHz 70.087 Hz √
720 x 480p (4:3) 27.027 MHz 31.500 kHz 60.000 Hz √*2
720 x 480p (16:9) 27.027 MHz 31.500 kHz 60.000 Hz √*2
800 x 600 40.000 MHz 37.879 kHz 60.317 Hz √
1024 x 768 65.000 MHz 48.363 kHz 60.004 Hz √
1280 x 720p 74.250 MHz 37.500 kHz 50.000 Hz √*2
1280 x 720p 74.250 MHz 45.000 kHz 60.000 Hz √*2
1280 x 960 108.000 MHz 60.000 kHz 60.000 Hz √
1280 x 1024 108.000 MHz 63.981 kHz 60.020 Hz √
1600 x 1200 162.000 MHz 75.000 kHz 60.000 Hz √
1680 x 1050 119.000 MHz 64.674 kHz 59.883 Hz √*2
1680 x 1050 146.250 MHz 65.290 kHz 59.954 Hz √*2
1920 x 1080 138.500 MHz 66.587 kHz 59.934 Hz √
1920 x 1080p 74.250 MHz 27.000 kHz 24.000 Hz √*2
1920 x 1080p 74.250 MHz 28.125 kHz 25.000 Hz √*2
1920 x 1080p 74.250 MHz 33.750 kHz 30.000 Hz √*2
1920 x 1080p 148.500 MHz 56.250 kHz 50.000 Hz √*2
1920 x 1080p 148.500 MHz 67.500 kHz 60.000 Hz √
1920 x 1200 154.000 MHz 74.038 kHz 59.950 Hz √
2048 x 1080 74.250 MHz 27.000 kHz 24.000 Hz √*2
2560 x 1440*1 146.250 MHz 43.945 kHz 29.935 Hz √*2
2560 x 1440*1 241.500 MHz 88.787 kHz 59.951 Hz √
*1 Recommended resolution
*2 The output device must be dened. Refer to the User’s Manual of the output device for further details.

13
Chapter 1 Introduction
●HDMI
Resolution Dot
clock
Horizontal
scanning
frequency
Vertical
scanning
frequency
HDMI
640 x 480 25.175 MHz 31.469 kHz 59.940 Hz √
640 x 480 25.200 MHz 31.500 kHz 60.000 Hz √
720 x 400 28.322 MHz 31.469 kHz 70.087 Hz √
720 (1440) × 480i (4:3) 27.027 MHz 15.750 kHz 60.000 Hz √
720 (1440) × 480i (16:9) 27.027 MHz 15.750 kHz 60.000 Hz √
720 x 480p (4:3) 27.027 MHz 31.500 kHz 60.000 Hz √
720 x 480p (16:9) 27.027 MHz 31.500 kHz 60.000 Hz √
720 (1440) × 576i (4:3) 27.000 MHz 15.625 kHz 50.000 Hz √
720 (1440) × 576i (16:9) 27.000 MHz 15.625 kHz 50.000 Hz √
720 x 576p (4:3) 27.000 MHz 31.250 kHz 50.000 Hz √
720 x 576p (16:9) 27.000 MHz 31.250 kHz 50.000 Hz √
800 x 600 40.000 MHz 37.879 kHz 60.317 Hz √
1024 x 768 65.000 MHz 48.363 kHz 60.004 Hz √
1280 x 720p 74.250 MHz 37.500 kHz 50.000 Hz √
1280 x 720p 74.250 MHz 45.000 kHz 60.000 Hz √
1280 x 960 108.000 MHz 60.000 kHz 60.000 Hz √
1280 x 1024 108.000 MHz 63.981 kHz 60.020 Hz √
1600 x 1200 162.000 MHz 75.000 kHz 60.000 Hz √
1680 x 1050 119.000 MHz 64.674 kHz 59.883 Hz √*2
1680 x 1050 146.250 MHz 65.290 kHz 59.954 Hz √*2
1920 x 1080 138.500 MHz 66.587 kHz 59.934 Hz √
1920 x 1080i 74.250 MHz 28.125 kHz 50.000 Hz √
1920 x 1080i 74.250 MHz 33.750 kHz 60.000 Hz √
1920 x 1080p 74.250 MHz 27.000 kHz 24.000 Hz √
1920 x 1080p 74.250 MHz 28.125 kHz 25.000 Hz √
1920 x 1080p 74.250 MHz 33.750 kHz 30.000 Hz √
1920 x 1080p 148.500 MHz 56.250 kHz 50.000 Hz √
1920 x 1080p 148.500 MHz 67.500 kHz 60.000 Hz √
1920 x 1200 154.000 MHz 74.038 kHz 59.950 Hz √
2560 x 1440*1 146.250 MHz 43.945 kHz 29.935 Hz √
2560 x 1440*1 241.500 MHz 88.787 kHz 59.951 Hz √
*1 Recommended resolution
*2 The output device must be dened. Refer to the User’s Manual of the output device for further details.

14 Chapter 1 Introduction
1-5. Setting the Resolution
If the resolution is incorrect after connecting the monitor to a PC or if you want to change the resolution,
follow the procedure below.
●Windows 10
1. Right-click anywhere on the desktop except for on icons.
2. From the displayed menu, click "Display Settings".
3. In the "Customize your display" dialog box, click "Advanced display settings".
4. Select the monitor, and select the resolution from the "Resolution" pull-down menu.
5. Click "Apply".
6. When a conrmation dialog box appears, click "Keep changes".
●Windows 8.1 / Windows 7
1. For Windows 8.1, click the “Desktop” tile on the Start Screen to display the desktop.
2. Right-click anywhere on the desktop except for on icons.
3. From the displayed menu, click “Screen resolution”.
4. Select the monitor, and select the resolution from the "Resolution" pull-down menu.
5. Click "OK".
6. When a conrmation dialog box is displayed, click “Keep changes”.
Note
• When changing the size of the characters or other items that are displayed, select "Display" from the control
panel and change the scaling level.
●OS X Mountain Lion (10.8) or later
1. Select “ System Preferences” from the Apple menu.
2. When the "System Preferences" dialog box is displayed, click "Displays".
(If using OS X Mountain Lion (10.8), click "Displays" in "Hardware".)
3. In the displayed dialog box, select the "Display" tab and select "Change" in the "Resolutions" eld.
4. Select the resolution from the list of possible resolution settings.
If the target resolution is not displayed in the list, press and hold the Option key on the keyboard
and select "Change".
5. Your selection will be reected immediately. When you are satised with the selected resolution,
close the window.
●Mac OS X 10.7
1. Select “System Preferences” from the Apple menu.
2. When the "System Preferences" dialog box is displayed, click "Displays" in "Hardware".
3. On the displayed dialog box, select the "Display" tab and select the resolution in the "Resolutions"
eld.
4. Your selection will be reected immediately. When you are satised with the selected resolution,
close the window.

15
Chapter 2 Basic Adjustments/Settings
Chapter 2 Basic Adjustments/Settings
This chapter describes the basic functions that can be adjusted and set by touching the switches on the front
of the monitor.
For advanced adjustment and setting procedures using the Setting menu, see “Chapter 3 Advanced
Adjustments/Settings” (page 17).
2-1. Switch Operation Method
1. Displaying the operation guide
1. Touch any switch (except ).
The operation guide appears on the screen.
2.
Adjusting/setting
1. Touch a switch for adjustment/setting.
The Adjustment/Setting menu appears.
2. Use the switches to adjust/set the selected item, and then select to conrm.
3.
Exiting
1. Select to exit the menu.
2. When no menu is displayed, the operation guide will automatically disappear after a few seconds
if no switches are operated.
Note
• The contents of the guide will differ depending on the selected menu or status.
2-2. Switching Input Signals
When a monitor has multiple signal inputs, the signal to display on-screen can be changed.
When the input signal is switched, the connector name of the displayed signal appears at the bottom right
of the screen.

16 Chapter 2 Basic Adjustments/Settings
2-3. Switching the Display Mode (color mode)
This function allows easy selection of a display mode according to monitor application.
●Display Modes
Color Mode Purpose
Standard Mode Adjust color using the monitor's Setting menu.
Custom Select for conguring color settings according to your preference.
Adobe®RGB Suitable for color matching with Adobe®RGB compatible peripherals.
sRGB Suitable for color matching with sRGB compatible peripherals.
Calibration Mode (CAL mode) Adjusts the monitor's color using the monitor's SelfCalibration function or
the "ColorNavigator 6" color management software.
CAL1 Displays the screen adjusted by ColorNavigator 6 and SelfCalibration.
CAL2
CAL3
Note
• The Setting menu and the Mode names cannot be displayed at the same time.
• You can disable specic mode selections. For more information, see “Mode Skip” (page 30).
• The adjustment result of ColorNavigator 6 is reected in each of the following modes, depending on the
connector used for connecting the monitor and PC.
- CAL1: DVI
- CAL2: DisplayPort
- CAL3: HDMI
2-4. Adjusting the Brightness
The brightness of the screen can be adjusted to suit the installation environment or personal preference.
Adjustable Range
40 cd/m2 to 400 cd/m2

17
Chapter 3 Advanced Adjustments/Settings
Chapter 3 Advanced Adjustments/Settings
This chapter describes the advanced monitor adjustment and setting procedures using the Setting menu.
For the basic adjustment/setting functions using the switches on the front of the monitor, see “Chapter 2
Basic Adjustments/Settings” (page 15).
3-1. Basic Operation of the Setting Menu
1. Menu display
1. Touch any switch (except ).
The operation guide appears.
2. Select .
The Setting menu appears.
2.
Adjusting/setting
1. Choose a menu to adjust/set with , and then select .
The Sub menu appears.
2. Choose an item to adjust/set with , and then press .
The Adjustment/Setting menu appears.
3. Adjust/set the selected item with , and then select .
The Sub menu appears.
Selecting during adjustment/setting will cancel the adjustment/setting and restore the state prior to
making changes.

18 Chapter 3 Advanced Adjustments/Settings
3.
Exiting
1. Select .
The Setting menu appears.
2. Select .
The Setting menu exits.
Note
• The contents of the guide will differ depending on the selected menu or status.

19
Chapter 3 Advanced Adjustments/Settings
3-2. Setting Menu Functions
●Color
The setting details differ depending on the color mode selected.
When the color mode is Standard Mode (Custom / Adobe®RGB / sRGB)
Each color mode setting status can be adjusted according to personal preference.
Attention
• The same image may be seen in different colors on multiple monitors due to differences between individual
monitors. Make ne color adjustment visually when matching colors on multiple monitors.
Note
• Use the values shown in "cd/m2", "K" and "%" as a guide only.
Function Adjustable
Range Description
Color Mode Custom
Adobe®RGB
sRGB
CAL1
CAL2
CAL3
Switch to the desired mode according to the monitor application.
Note
• For more information on how to switch modes, see “2-3. Switching
the Display Mode (color mode)” (page 16).
• Regarding "CAL1 / CAL2 / CAL3" see page 22.
Brightness 40 cd/m2
to 400 cd/m2
The screen brightness is adjusted by changing the brightness of the
backlight (light source from the LCD back panel).
Note
• If the entered value cannot be set, the value will appear in
magenta. In such a case, change the value.
Temperature Native
4000 K to
10000 K
Adobe®RGB
sRGB
The color temperature can be adjusted.
The color temperature is used to express the hue of "White" or
"Black" by a numerical value. The value is expressed in degrees "K"
(Kelvin).
The screen becomes reddish at a low color temperature, and bluish
at a high color temperature, like the temperature of a ame.
Specify a color temperature in units of 100 K, or select a standard
name.
Note
• When you select "Native", the original color of the monitor (Gain:
100 % for each RGB) is displayed.
• “Gain” allows you to perform more advanced adjustment. When
gain is changed, the color temperature is changed to “User”.
• The gain preset values are set for each color temperature setting
value
.

20 Chapter 3 Advanced Adjustments/Settings
Function Adjustable
Range Description
Gamma 1.6 to 2.7
Adobe®RGB
sRGB
Adjust the gamma.
The brightness of the monitor varies depending on the input signal,
however, the variation rate is not simply proportional to the input
signal. The control performed to keep the balance between the input
signal and the brightness of the monitor is called “Gamma correction”.
Set the gamma, or select a standard name.
Color Gamut Native
Adobe®RGB
sRGB
Set the color reproduction area (color gamut).
"Color Gamut" is the range of colors that devices such as monitors, digital
cameras and printers can represent. Multiple standards are dened.
Note
• Select "Native", to display the original color gamut of the monitor.
• The method of displaying colors outside the monitor's displayable
range within the dened color gamut can be set. For more
information, see “Clipping” (page 20).
Advanced
Settings
Hue -100 to 100 Adjust the hue.
Note
• Using this function may make some color gradations unavailable
for display.
Saturation -100 to 100 Adjust the color saturation.
Note
• Using this function may make some color gradations unavailable
for display.
• The minimum value (-100) changes the screen to monochrome.
Clipping On
Off
The method of displaying colors outside the monitor's displayable
range within the color gamut specied in accordance with ”Color
Gamut” (page 20) can be set.
• "On"
The range of colors that are
displayable on the monitor
will be accurately displayed in
accordance with the standard.
Colors outside the displayable
range will be saturated.
• "Off"
Displays colors with priority on the
color gradation rather than the color
accuracy. The vertices of the color
gamut dened in the standard move
to a range that can be displayed by
the monitor. This allows the closest
colors displayable by the monitor to
be displayed.
Color gamut displayable by the monitor
Color gamut defined by standard
Color gamut displayed on screen
Note
• The diagrams shown above are conceptual diagrams, and they do
not display the actual color gamut of the monitor.
• This setting will be disabled if "Native" is selected at “Color Gamut”
(page 20)
.