Eizo FlexScan EV2430 User manual

Important
Please read this “User’s Manual”, and “PRECAUTIONS” (separate
volume) carefully to familiarize yourself with safe and effective usage.
•Refer to the “Setup Guide” for information on the installation /
connection of the monitor.
•For the latest product information including the “User’s Manual”,
refer to our web site :
http://www.eizoglobal.com
Color LCD Monitor
User’s Manual

2
Location of Caution Statement
This product has been adjusted specically for use in the region to which it was originally shipped. If
operated outside this region, the product may not perform as stated in the specications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information condential unless
prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every
effort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specications are subject to change without notice.

3
Notice for this monitor
Notice for this monitor
This product is suited to general purposes like creating documents, viewing multimedia content (Assuming
usage of approximately 12 hours per day).
If using this product for the following kinds of applications, where an extremely high degree of reliability and
safety is required, then measures should be in place to maintain safety while using this product.
• Transportation equipment (ships, aircraft, trains, and automobiles)
• Safety devices (Disaster prevention systems, security control systems, etc.)
• Life-critical devices (medical devices, such as life-support devices and operating room devices)
• Nuclear energy control devices (Nuclear energy control systems, security control systems of nuclear facilities, etc.)
• Major system communication devices (operation control systems of transportation systems, air trafc control systems, etc.)
This product has been adjusted specically for use in the region to which it was originally shipped. If the
product is used outside the region, it may not operate as specied in the specications.
This product may not be covered by warranty for uses other than those described in this manual.
The specications noted in this manual are only applicable when the following are used:
• Power cords provided with the product
• Signal cables specied by us
Only use optional products manufactured or specied by us with this product.
If you place this product on a lacquer-coated desk, the color may adhere to the bottom of the stand due to
the composition of the rubber. Check the desk surface before use.
It takes about 30 minutes (under our measurement conditions) for the monitor display to stabilize. Please
wait 30 minutes or more after the monitor power has been turned on, and then adjust the monitor.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and
maintain a stable display.
When the screen image is changed after displaying the same image for extended periods of time, an
afterimage may appear. Use the screen saver or power save function to avoid displaying the same image for
extended periods of time. Depending on the image, an afterimage may appear even if it was displayed for
a short period of time. To remove such a phenomenon, change the image or keep the power turned off for
several hours.
If the monitor displays continuously over a long period of time, dark smudges or burn-in may appear. To
maximize the life of the monitor, we recommend the monitor be turned off periodically.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer
to “Cleaning” (page 4)).
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may
appear on the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994 % or higher.
The backlight of the LCD panel has a xed lifetime. Depending on the usage pattern, such as usage for
long continuous periods, the lifespan of the backlight may run out sooner, requiring replacement. When the
screen becomes dark or begins to icker, please contact your local EIZO representative.
Do not press on the LCD panel or edge of the frame strongly, as this may result in display malfunctions, such
as interference patterns, etc. If pressure is continuously applied to the LCD panel surface, the liquid crystal
may deteriorate or the LCD panel may be damaged. (If the pressure marks remain on the panel, leave the
monitor with a black or white screen. The symptom may disappear.)
Do not scratch or press on the LCD panel with any sharp objects, at this may result in damage to the LCD
panel. Do not attempt to brush with tissues as this may scratch the panel.

4Notice for this monitor
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew
condensation may occur on the interior and exterior surfaces of the monitor. In that case, do not turn the
monitor on. Instead wait until the dew condensation disappears, otherwise it may cause some damage to the
monitor.
Cleaning
The stains on the cabinet and LCD panel surface can be removed by moistening part of a soft cloth with water.
Attention
• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet
or LCD panel, and also quality deterioration of the image.
• Never use thinner, benzine, wax, or abrasive cleaner as they may damage the cabinet or LCD panel surface.
Note
• It is recommended that ScreenCleaner (available as an option) be used to clean the cabinet and LCD panel surface.
To use the monitor comfortably
• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor
according to the environmental conditions.
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.

5
CONTENTS
CONTENTS
Notice for this monitor ......................................... 3
Cleaning .................................................................... 4
To use the monitor comfortably ............................. 4
CONTENTS............................................................. 5
Chapter 1 Introduction....................................... 7
1-1. Features ......................................................... 7
1-2. Controls and Functions ............................... 8
●Front ................................................................ 8
●Rear ................................................................. 9
1-3. Basic Operations and Functions ...............10
●Basic operation of the Setting menu ..............10
●Functions ........................................................11
Chapter 2 Adjusting Screens .......................... 12
2-1. Compatible Resolutions .............................12
●Analog Input (D-Sub) .....................................12
●Digital Input (DVI-D) .......................................12
●Digital Input (DisplayPort) ..............................12
2-2. Setting the Resolution ................................13
●Windows 10 ....................................................13
●Windows 8.1 / Windows 7 ..............................13
●OS X Mountain Lion (10.8) or later .................13
●Mac OS X 10.7 ...............................................13
2-3. Adjusting Color ............................................14
●To select the display mode (color mode) .......14
●To perform advanced adjustments ................14
●Adjustable settings in each mode ..................15
●To adjust brightness .......................................15
●To adjust contrast ...........................................16
●To adjust color temperature ...........................16
●To adjust gamma ...........................................17
●To adjust the color saturation .........................17
●To adjust hue ..................................................18
●To adjust gain .................................................18
2-4. Screen Adjustment ......................................19
●Digital Signal Input .........................................19
●Analog Signal Input ........................................19
2-5. Screen Size Changing ................................ 22
●Screen Size Changing .................................. 22
●To adjust brightness of non-display area ...... 22
Chapter 3 Setting Monitor ............................... 23
3-1. Adjusting Volume........................................ 23
3-2. Selecting sound source while using the
DisplayPort signal input............................. 23
3-3. Enabling / Disabling DDC/CI
communication .......................................... 23
3-4. Locking Operation Buttons ....................... 24
3-5. Setting Orientation ..................................... 24
3-6. Showing and hiding the EIZO logo ........... 24
3-7. Changing Setting Menu Display
Position ........................................................ 25
3-8. Setting Language........................................ 25
3-9. Resetting the Monitor to the Default
Settings ........................................................ 26
●To reset the color adjustments ...................... 26
●To reset “EcoView Sense Settings” .............. 26
●To reset all adjustments to the default
settings .......................................................... 26
Chapter 4 Power Saving Functions ................ 27
4-1. Setting Power Saving ................................. 27
●Monitor .......................................................... 27
●Audio Output ................................................. 28
4-2. Setting Power Indicator.............................. 28
4-3. Enabling / Disabling Automatic
Brightness Adjustment ............................. 28
●Auto EcoView ................................................ 28
●EcoView Optimizer 2 ..................................... 29
4-4. Setting the power saving mode when a
person leaves the monitor ......................... 29
4-5. Checking the power saving level ...............31
4-6. Enabling / Disabling Auto Power-OFF.......31
Chapter 5 Troubleshooting.............................. 32
5-1. No picture .................................................... 32
5-2. Imaging problems (for both digital and
analog).......................................................... 33
5-3. Imaging problems (for digital only) .......... 34
5-4. Imaging problems (for analog only) ......... 34
5-5. Other problems ........................................... 35

6CONTENTS
Chapter 6 Reference ........................................ 36
6-1. Attaching the Optional Arm....................... 36
6-2. Detaching/Attaching Stand Base...............37
6-3. Attaching/Detaching Cable Holder ........... 40
6-4. Connecting Multiple PCs ........................... 42
●To switch among input signals .......................42
●To set input signal selection .......................... 43
6-5. Using the USB Hub Function..................... 43
●Connection Procedure (Setup of USB
Function) ........................................................ 44
6-6. Displaying Monitor Information ................ 44
6-7. Specications ............................................. 45
●Accessories ................................................... 46
Appendix.............................................................. 47
Trademark ................................................................47
License .....................................................................47
ENERGY STAR .........................................................47
FCC Declaration of Conformity ............................ 48

7
Chapter 1 Introduction
Chapter 1 Introduction
Thank you very much for choosing an EIZO color LCD monitor.
1-1. Features
• 24.1″ wide format LCD
• Supports a resolution of 1920 × 1200
• Applicable to DisplayPort (applicable to 8 bit)*1
The DisplayPort input receives both an image signal and an audio signal via a single DisplayPort cable.
*1 When transmitting an audio signal using the DtisplayPort cable, the graphics board must be compatible with audio
output (see “6-7. Specications” (page 45)).
• The Color Mode function allows the user to select the display mode optimum to the displayed image.
- The Paper mode reproduces a printed paper effect on the monitor. In Paper mode, the amount of blue light
emitted from the screen is reduced by changing the color tone and controlling the brightness.
See “To select the display mode (color mode)” (page 14).
• Power saving function
Suppressing the power consumption*2 reduces the carbon dioxide emissions. This product is equipped with power saving
function.
- 0 W power consumption when the main power is off
Equipped with main power switch.
When the monitor is not required, the power supply can be shut off using the main power switch.
- Auto EcoView
The ambient light sensor on the front side of the monitor detects the environmental brightness to adjust the screen
brightness automatically and comfortably.
See “Auto EcoView” (page 28).
- EcoView Optimizer 2
The monitor automatically adjusts the screen brightness according to the white level of the input signal. This
function can reduce the power consumption while maintaining the brightness specied by the input signal.
See “EcoView Optimizer 2” (page 29).
- EcoView Sense
The sensor on the front side of the monitor detects the movement of a person. When a person moves away from the
monitor, the monitor shifts to the power saving mode automatically and does not display the images on the screen.
Therefore, the function reduces the power consumption. The sensitivity and time until the power saving mode is
activated can be set according to the monitor usage environment and movement of the user.
See “4-4. Setting the power saving mode when a person leaves the monitor” (page 29).
*2 Reference values:
Maximum power consumption: 36 W (Brightness Max., when a USB device is connected, speaker working, at
default settings)
Standard power consumption: 12 W (Brightness 120 cd/m2, when no USB device is connected, speaker not working,
at default settings)
• Supports portrait and landscape formats
• Displays HDCP (High-bandwidth Digital Protection) protected contents.
Note
• This monitor supports the portrait display. This function allows you to change the orientation of the Setting menu when
using the monitor screen in vertical display position (see “3-5. Setting Orientation” (page 24)).
• When using the monitor screen in a portrait position, the graphics board supporting portrait display is required. When
placing the monitor in a portrait position, the settings of your graphics board need to be changed. Refer to the User’s
Manual of the graphics board for details.

8Chapter 1 Introduction
1-2. Controls and Functions
●Front
Setting menu*1
6 7 8 9521 3 4
1. EcoView Sense sensor Detects the movement of a person in front of the monitor (EcoView Sense function (page
29)).
2. Ambient light sensor Detects ambient brightness (Auto EcoView function (page 28)).
3. button Displays the setting menu of the power saving function (Auto EcoView (page 28) and
EcoView Optimizer 2 (page 29)) and EcoView Sense (page 29).
4. button Switches input signals for display (page 42).
5. button Switches the color mode (page 14).
6. button Displays the Setting menu, determines an item on the menu screen, and saves values
adjusted (page 10).
7. , button*2
• Provides the menu selection as well as the adjustment and setting of a function.
• button: Displays the volume adjustment menu (page 23).
button: Displays the Brightness adjustment menu (page 15).
8. button Turns the power on or off.
9. Power indicator
Indicates the monitor’s operation status.
White: Operating
Orange: Power saving mode
OFF: Main power / Power off
*1 See “1-3. Basic Operations and Functions” (page 10) for how to use.
*2 In this User’s Manual, the button may be hereafter simply displayed as , and the button as .

9
Chapter 1 Introduction
●Rear
13
15
14
20
21
21
19
18
17
16
121110
*3
*3
10. Main power switch Turns the main power on ( ) or off ( ).
11. Power connector Connects the power cord.
12. Input signal connector Left: DisplayPort connector / Center: DVI-D connector / Right: D-Sub mini15-pin
connector
13. Security lock slot Complies with Kensington’s MicroSaver security system.
14. Speaker Outputs audio.
15. Handle
Handle used for transportation
Attention
• Firmly grasp and hold the monitor by the bottom while grabbing the handle, and carefully
convey the monitor so as not to drop it.
16. USB downstream port Connects a peripheral USB device.
17. USB upstream port Connects the USB cable for using the USB Hub function (page 43).
18. Headphone jack Connects the headphones.
19. Analog audio input
connector Outputs external audio from the monitor.
20. Stand*4 Adjusts the height and angle (tilt and swivel) of the monitor.
21. Cable holder Covers the monitor cables.
*3 See “6-3. Attaching/Detaching Cable Holder” (page 40) for how to attach the cable holder.
*4 An optional arm (or an optional stand) can be attached by removing the stand (see “6-1. Attaching the Optional Arm” (page 36)).

10 Chapter 1 Introduction
1-3. Basic Operations and Functions
●Basic operation of the Setting menu
1.
Displaying the Setting menu
1. Press . The Setting menu appears.
2.
Adjusting / Setting
1. Choose a menu to adjust / set with , , and then press . The Sub menu appears.
2. Choose an item to adjust / set with , , and then press . The adjustment / setting menu appears.
3. Adjust / set the selected item with , , and then press .
3.
Exiting
1. Choose “Return” from the Sub menu and press . The Setting menu appears.
2. Choose “Exit” from the Main menu and press . The Setting menu quits.
Note
• The Setting menu can also be exited by pressing twice quickly.

11
Chapter 1 Introduction
●Functions
The following table shows the Setting menu and setting items of each menu.
Main menu Setting Reference
Color*1 Brightness “2-3. Adjusting Color” (page 14)
Contrast
Temperature
Gamma
Advanced Settings Saturation
Hue
Gain
Color Reset “To reset the color adjustments” (page 26)
Screen Screen Size “Screen Size Changing” (page 22)
Smoothing “2-4. Screen Adjustment” (page 19)
Analog Adjustment*2 Auto Screen Adjust
Auto Range Adjust
Clock
Phase
Hor.Position
Ver.Position
Sound Source “3-2. Selecting sound source while using
the DisplayPort signal input” (page 23)
Power Save “Audio Output” (page 28)
PowerManager Power Save “4-1. Setting Power Saving” (page 27)
Eco Timer “4-6. Enabling / Disabling Auto Power-
OFF” (page 31)
Monitor Settings Input Signal “To set input signal selection” (page 43)
Power Indicator “4-2. Setting Power Indicator” (page 28)
Language “3-8. Setting Language” (page 25)
DDC/CI “3-3. Enabling / Disabling DDC/CI
communication” (page 23)
Border Intensity “To adjust brightness of non-display area”
(page 22)
Menu Settings Orientation “3-5. Setting Orientation” (page 24)
Logo “3-6. Showing and hiding the EIZO logo”
(page 24)
Menu Position “3-7. Changing Setting Menu Display
Position” (page 25)
Reset “To reset all adjustments to the default
settings” (page 26)
Information “6-6. Displaying Monitor Information”
(page 44)
*1 The adjustment / settings available on the “Color” menu depend on the selected Color mode (see “Adjustable
settings in each mode” (page 15)).
*2 These functions can be adjusted with analog input.

12 Chapter 2 Adjusting Screens
Chapter 2 Adjusting Screens
2-1. Compatible Resolutions
The monitor supports the following resolutions.
●Analog Input (D-Sub)
Resolution Applicable Signals Vertical Scan
Frequency Dot Clock
640 × 480 VGA 60 Hz
202.5 MHz
(Max.)
800 × 600 VESA 60 Hz
1024 × 768 VESA 60 Hz
1280 × 720*1 CEA-861 60 Hz
1280 × 960 VESA 60 Hz
1280 × 1024 VESA 60 Hz
1600 × 1200 VESA 60 Hz
1680 × 1050 VESA CVT, VESA CVT RB 60 Hz
1920 × 1200*2 VESA CVT, VESA CVT RB 60 Hz
●Digital Input (DVI-D)
Resolution Applicable Signals Vertical Scan
Frequency Dot Clock
640 × 480 VGA 60 Hz
162 MHz
(Max.)
800 × 600 VESA 60 Hz
1024 × 768 VESA 60 Hz
1280 × 720*1 CEA-861 60 Hz
1280 × 960 VESA 60 Hz
1280 × 1024 VESA 60 Hz
1600 × 1200 VESA 60 Hz
1680 × 1050 VESA CVT, VESA CVT RB 60 Hz
1920 × 1200*2 VESA CVT RB 60 Hz
●Digital Input (DisplayPort)
Resolution Applicable Signals Vertical Scan
Frequency Dot Clock
640 × 480 VGA, CEA-861 60 Hz
162 MHz
(Max.)
720 × 480 (4:3) CEA-861 60 Hz
720 × 480 (16:9) CEA-861 60 Hz
800 × 600 VESA 60 Hz
1024 × 768 VESA 60 Hz
1280 × 720*1 CEA-861 60 Hz
1280 × 960 VESA 60 Hz
1280 × 1024 VESA 60 Hz
1600 × 1200 VESA 60 Hz
1680 × 1050 VESA CVT, VESA CVT RB 60 Hz
1920 × 1200*2 VESA CVT RB 60 Hz
*1 For this resolution, the “Screen Size” setting is “Full Screen” (see “2-5. Screen Size Changing” (page 22)).
*2 Recommended resolution

13
Chapter 2 Adjusting Screens
2-2. Setting the Resolution
When you connect the monitor to the PC and nd that the resolution is improper, or when you want to change the
resolution, follow the procedure below.
●Windows 10
1. Right-click the mouse anywhere on the desktop except on icons.
2. From the displayed menu, click “Display settings”.
3. If multiple monitors are connected to the computer, select the monitor.
4. Select the resolution from the “Resolution” pull-down menu.
5. When a conrmation screen appears, click “Keep changes”.
●Windows 8.1 / Windows 7
1. For Windows 8.1, click the “Desktop” tile on the Start Screen to display the desktop.
2. Right-click the mouse anywhere on the desktop except on icons.
3. From the displayed menu, click “Screen resolution”.
4. Select the monitor, and select the resolution from the “Resolution” pull-down menu.
5. Click the “OK” button.
6. When a conrmation dialog box is displayed, click “Keep changes”.
●OS X Mountain Lion (10.8) or later
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” dialog box is displayed, click “Displays”. (For OS X Mountain Lion (10.8),
click “Displays” for “Hardware”.)
3. On the displayed dialog box, select the “Display” tab, then choose “Scaled” for “Resolutions”.
4. The list of selectable resolutions is displayed. Select the desired resolution. If the desired resolution is not
displayed in the list, hold down the Option key and select “Scaled”.
5. Your selection will be reected immediately. When you are satised with the selected resolution, close the
window.
●Mac OS X 10.7
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” dialog box is displayed, click “Displays” for “Hardware”.
3. On the displayed dialog box, select the “Display” tab and select desired resolution in the “Resolutions” eld.
4. Your selection will be reected immediately. When you are satised with the selected resolution, close the
window.

14 Chapter 2 Adjusting Screens
2-3. Adjusting Color
●To select the display mode (color mode)
This function allows easy selection of a desired mode according to monitor application.
Display Modes
Mode Purpose
User1 Select this to dene a desired set of parameter settings.
User2
sRGB Suitable for color matching with sRGB compatible peripherals.
Paper Produces a printed paper effect. Suitable for displaying images from media such as books
and documents.
Movie Suitable for playing back animated images.
The mode menu
appears.
Procedure
1. Press .
The mode menu appears at the bottom left of the screen.
2. The mode among the list is highlighted in turn each time is pressed.
You can switch the mode with or while the mode menu is displayed.
Note
• The Setting menu and the Mode menu cannot be displayed at the same time.
●To perform advanced adjustments
The “Color” menu of the Setting menu allows you to set and save the independent color adjustment for each
mode.
Attention
• It takes about 30 minutes for the monitor display to stabilize. Please wait 30 minutes or more after the monitor power
has been turned on, and then adjust the monitor.
• Perform the range adjustment rst when adjusting color for analog signals (see “To adjust color gradation
automatically” (page 21)).
• The same image may be seen in different colors on multiple monitors due to their monitor-specic characteristics.
Make ne color adjustment visually when matching colors on multiple monitors.

15
Chapter 2 Adjusting Screens
●Adjustable settings in each mode
The adjustable settings depend on the mode. (Non-adjustable or non-settable function cannot be selected.)
√: Adjustable -: Not adjustable
Function Color Mode
User1 User2 sRGB Paper Movie
Brightness √√√√√
Contrast √ √ - - √
Temperature √ √ - √ √
Gamma √ √ - - -
Advanced Settings Saturation √ √ - - √
Hue √ √ - - √
Gain √ √ - - -
Color Reset √√√√√
●To adjust brightness
The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD back
panel).
Adjustable range
0 to 100
Procedure
1. Press .
2. Use or for adjustment.
3. Press to exit.
Note
• If you feel that the image is too dark even if the brightness is set to 100, adjust the contrast.
• Alternatively, you can use “Brightness” under “Color” in the Adjustment menu to adjust it.
• To adjust the screen brightness automatically and comfortably, see “4-3. Enabling / Disabling Automatic Brightness
Adjustment” (page 28).

16 Chapter 2 Adjusting Screens
●To adjust contrast
The brightness of the screen is adjusted by varying the video signal level.
Adjustable range
0 to 100
Procedure
1. Choose “Color” in the Setting menu, and press .
2. Choose “Contrast” in the “Color” menu, and press .
The “Contrast” menu appears.
3. Use or for adjustment.
4. Press to exit.
Note
• In the contrast of 50, every color gradation is displayed.
• When adjusting the monitor, it is recommended to perform the brightness adjustment which may not lose the gradation
characteristics, prior to the contrast adjustment.
• Perform the contrast adjustment in the following cases.
- When you feel the image is too dark even if the brightness is set to 100 (Set the contrast to higher than 50.)
●To adjust color temperature
Color temperature can be adjusted.
The color temperature is normally used to express the hue of “White” and / or “Black” by a numerical value.
The value is expressed in degrees “K” (Kelvin).
The screen becomes reddish at a low color temperature, and bluish at a high color temperature, like the ame
temperature. A gain preset value is set for each color temperature setting value.
Adjustable range
Off, 4000 K-10000 K (specied by every 500 K unit, including 9300 K)
Procedure
1. Choose “Color” in the Setting menu, and press .
2. Choose “Temperature” in the “Color” menu, and press .
The “Temperature” menu appears.
3. Use or for adjustment.
4. Press to exit.
Note
• The value shown in “K” is available only as reference.
• “Gain” allows you to perform more advanced adjustment (see “To adjust gain” (page 18)).
• If you set to “Off”, the image is displayed in the preset color of the monitor (Gain: 100 for each RGB).
• When gain is changed, the color temperature is changed to “Off”.

17
Chapter 2 Adjusting Screens
●To adjust gamma
Gamma can be adjusted. The brightness of the monitor varies depending on the input signal, however, the
variation rate is not proportional to the input signal. To keep the balance between the input signal and the
brightness of the monitor is called as “Gamma correction”.
Adjustable range
1.8, 2.0, 2.2
Procedure
1. Choose “Color” in the Setting menu, and press .
2. Choose “Gamma” in the “Color” menu, and press .
The “Gamma” menu appears.
3. Use or for adjustment.
4. Press to exit.
Note
• If “Paper” is selected for the color mode, “Paper” is displayed for the gamma value. The setting “Paper” is specially
meant to get the displayed image look like it is printed on paper.
●To adjust the color saturation
This function allows you to adjust color saturation.
Adjustable range
-50 to 50
Procedure
1. Choose “Color” in the Setting menu, and press .
2. Choose “Advanced Settings” in the “Color” menu, and press .
3. Choose “Saturation” in the “Advanced Settings” menu, and press .
The “Saturation” menu appears.
4. Use or for adjustment.
5. Press to exit.
Attention
• Using this function may make some color gradations unavailable for display.
Note
• The minimum value (-50) changes the screen to monochrome.

18 Chapter 2 Adjusting Screens
●To adjust hue
This function allows you to adjust hue.
Adjustable range
-50 to 50
Procedure
1. Choose “Color” in the Setting menu, and press .
2. Choose “Advanced Settings” in the “Color” menu, and press .
3. Choose “Hue” in the “Advanced Settings” menu, and press .
The “Hue” menu appears.
4. Use or for adjustment.
5. Press to exit.
Attention
• Using this function may make some color gradations unavailable for display.
●To adjust gain
The brightness of each color component red, green, and blue is called “Gain”. You can change the hue of
“white” by adjusting gain.
Adjustable range
0 to 100
Procedure
1. Choose “Color” in the Setting menu, and press .
2. Choose “Advanced Settings” in the “Color” menu, and press .
3. Choose “Gain” in the “Advanced Settings” menu, and press .
The “Gain” menu appears.
4. Adjust gain with or for each of red, green, and blue.
5. Press to exit.
Attention
• Using this function may make some color gradations unavailable for display.
Note
• The value of gain changes with that of color temperature.
• When gain is changed, the color temperature is changed to “Off”.

19
Chapter 2 Adjusting Screens
2-4. Screen Adjustment
●Digital Signal Input
When digital signals are input, images are displayed correctly based on the preset data of the monitor, but if
characters and / or lines appear blurred, go to “To modify blurred characters / lines” (page 21).
When performing more advanced adjustment, see “2-3. Adjusting Color” (page 14) and subsequent pages.
●Analog Signal Input
Attention
• It takes about 30 minutes for the monitor display to stabilize. Please wait 30 minutes or more after the monitor power
has been turned on, and then adjust the monitor.
• The Self Adjust (automatic screen adjustment) function does not work for the images under the resolution of 800 × 600
(SVGA).
• The self adjustment (or automatic screen adjustment) function works correctly when an image is fully displayed over the
Windows or Macintosh display area. They do not work properly in the cases below:
- When an image is displayed only on a part of the screen (command prompt window, for example)
- When a black background (wallpaper, etc.) is in use
Also, these functions cannot work properly in some graphic boards.
The monitor screen adjustment is used to suppress ickering of the screen or adjust screen position and screen
size correctly according to the PC to be used.
Note
• The Self Adjust function works when all of the following conditions are satised:
- When a signal is input into the monitor for the rst time or when a resolution or vertical / horizontal scan frequency
not used before is set
If the screen is not displayed correctly even after performing the Self Adjust operation, adjust the screen
according to the procedures on the following pages to use the monitor comfortably.
Setting Procedures
1.
Adjustickering,screenposition,andsizeautomatically.
Procedure
1. Choose “Screen” in the Setting menu, and press .
2. Choose “Analog Adjustment” in the “Screen” menu, and press .
3. Choose “Auto Screen Adjust” in the “Analog Adjustment” menu, and press .
4. Select “Yes” with or , and press .
Flickering, screen position, and screen size are corrected by the auto-adjustment function.
If the screen is not displayed correctly even after performing the auto adjustment, perform adjustments
according to the following procedure. If the screen is displayed correctly, go to “3. Adjusting color gradation.”
(page 21).

20 Chapter 2 Adjusting Screens
2.
Choose “Screen” from the Setting menu to perform advanced adjustments.
Adjust the clock, phase and position, in this order.
●To eliminate vertical bars
Procedure
1. Choose “Analog Adjustment” in the “Screen” menu, and press .
2. Choose “Clock” in the “Analog Adjustment” menu, and press .
The “Clock” menu appears.
3. Adjust the clock with or to eliminate vertical bars.
Press or slowly so as not to miss the adjustment point.
4. Press to exit.
When blurring, ickering or bars appear on the screen after adjustment, proceed to “To remove ickering or blurring ”.
●Toremoveickeringorblurring
Procedure
1. Choose “Analog Adjustment” in the “Screen” menu, and press .
2. Choose “Phase” in the “Analog Adjustment” menu, and press .
The “Phase” menu appears.
3. Adjust the phase with or to minimize ickering or blurring.
4. Press to exit.
When vertical bars appear on the screen after adjustment, go back to “To eliminate vertical bars ”.
(Clock → Phase → Position)
Attention
• Flickering or blurring may not be eliminated depending on your PC or graphics board.