Eizo ColorEdge PROMINENCE CG3146 User manual

Important
Please read this “User’s Manual”, and “PRECAUTIONS” (separate
volume) carefully to familiarize yourself with safe and e󰀨ective
usage.
•Refer to the “Setup Guide” for information on the installation /
connection of the monitor.
•For the latest product information including the “User’s Manual”,
refer to our web site :
www.eizoglobal.com
HDR Reference Monitor
User’s Manual
Thank you for purchasing our HDR reference monitor.

2
Location of Caution Statement
This product has been adjusted specically for use in the region to which it was originally shipped. If
operated outside this region, the product may not perform as stated in the specications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information condential unless
prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every
e󰀨ort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specications are subject to change without notice.

3
Notice for This Monitor
Notice for This Monitor
About the Usage of This Product
This product is suited for producing videos, where accurate color reproduction is a priority.
This product has been adjusted specically for use in the region to which it was originally shipped. If the
product is used outside the region, it may not operate as specied in the specications.
This product may not be covered by warranty for uses other than those described in this manual.
The specications noted in this manual are only applicable when the following are used:
• Power cords provided with the product
• Signal cables specied by us
Only use optional products manufactured or specied by us with this product.
About the LCD Panel
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may
appear on the LCD panel, this is not a malfunction. Percentage of e󰀨ective dots: 99.9994 % or higher.
It takes about 3 minutes (under our measurement conditions) for the monitor display to stabilize. For highly
accurate adjustments, please wait 20 minutes or more after the monitor power has been turned on.
If you switch SDR color modes and HDR color modes, wait 30 minutes or more after switching the color
modes, and then adjust the monitor.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and
maintain a stable display.
When the screen image is changed after displaying the same image for extended periods of time, an
afterimage may appear. Use the screen saver or power save function to avoid displaying the same image for
extended periods of time. Depending on the image, an afterimage may appear even if it was displayed for
a short period of time. To remove such a phenomenon, change the image or keep the power turned o󰀨 for
several hours.
If the monitor displays continuously over a long period of time, smudges or burn-in may appear. To maximize
the life of the monitor, we recommend the monitor be turned o󰀨 periodically. Use the power button on the
front of the monitor to turn it o󰀨.
The backlight of the LCD panel has a xed lifetime. Depending on the usage pattern, such as usage for
long continuous periods, the lifespan of the backlight may run out sooner, requiring replacement. When the
screen becomes dark or begins to icker, please contact your local EIZO representative.
Do not press on the LCD panel or edge of the frame strongly, as this may result in display malfunctions, such
as interference patterns, etc. If pressure is continuously applied to the LCD panel surface, the liquid crystal
may deteriorate or the LCD panel may be damaged. (If the pressure marks remain on the panel, leave the
monitor with a black or white screen. The symptom may disappear.)
Do not scratch or press on the LCD panel with any sharp objects, as this may result in damage to the LCD
panel. Do not attempt to brush with tissues as this may scratch the panel.

4Notice for This Monitor
About the Installation
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew
condensation may occur on the interior and exterior surfaces of the monitor. In that case, do not turn the
monitor on. Instead wait until the dew condensation disappears, otherwise it may cause some damage to the
monitor.
If you place this product on a lacquer-coated desk, the color may adhere to the bottom of the stand due to
the composition of the rubber. Check the desk surface before use.
About the Maintenance
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer
to “Cleaning” (page 4)).
Update program for the internal software (rmware) of the monitor may be provided to improve the
performance of monitor and other purposes. Select “Software and Drivers” in “Support” from our web site
(www.eizoglobal.com), enter the product name, and perform search.
Cleaning
The stains on the cabinet and LCD panel surface can be removed by using the provided ScreenCleaner.
Attention
• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet
or LCD panel, and also quality deterioration of the image.
• Never use thinner, benzine, wax, or abrasive cleaner as they may damage the cabinet or LCD panel surface.
To Use the Monitor Comfortably
• An excessively dark or bright screen may a󰀨ect your eyes. Adjust the brightness of the monitor
according to the environmental conditions.
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.

5
Contents
Contents
Notice for This Monitor......................................... 3
Cleaning .................................................................... 4
To Use the Monitor Comfortably ............................ 4
Contents................................................................. 5
Chapter 1 Introduction....................................... 6
1-1. Features ......................................................... 6
●Large built-in high resolution 4K LCD
that is advantageous for video production ...... 6
●Support for HDR (High Dynamic Range)
video................................................................ 6
●Support for SDI signal input or output
for long-distance transmissions ...................... 6
●Built-in mode for automatically switching
to the optimal color settings ............................ 7
●Various functions that support color
grading work.................................................... 7
●Equipped with a USB Hub function................. 7
1-2. Controls and Functions ............................... 8
●Front ................................................................ 8
●Rear................................................................. 9
Chapter 2 Basic Adjustments/Settings.......... 11
2-1. Switching Input Signals ..............................11
2-2.
Switching the Display Mode (color mode) ...11
●Display Modes................................................12
●Color Mode Setting Values ............................13
2-3. Using the Quick Check Function ...............14
Chapter 3 Advanced Adjustments/Settings ... 15
3-1. Basic Operation of the Setting Menu ........15
3-2. Setting Menu Functions ..............................17
●Signal .............................................................17
●Color...............................................................19
●SelfCalibration............................................... 26
●Screen ........................................................... 27
●Preferences....................................................31
●Languages .................................................... 34
●Information .................................................... 34
Chapter 4 SelfCalibration ................................ 35
4-1. SelfCalibration functions........................... 36
4-2. Setting targets............................................. 38
4-3. Executing ..................................................... 38
●Executing regardless of a schedule.............. 38
●Executing by setting a schedule ................... 38
●
Activating SelfCalibration in Standard Mode ... 38
●
Activating SelfCalibration in Advanced Mode... 39
4-4. Checking results......................................... 39
Chapter 5 Custom Key Settings...................... 40
5-1. Basic Operation of the Custom Keys ....... 40
5-2. Assigning a Function to a Custom Key.... 40
●Functions that can be Assigned to
Custom Keys ..................................................42
Chapter 6 Administrator Settings................... 43
6-1. Basic Operation of the "Administrator
Settings" Menu............................................ 43
6-2. "Administrator Settings" Menu
Functions ..................................................... 44
Chapter 7 SDR/HDR Settings.......................... 45
7-1. About Each Color Mode ............................. 45
●Types and Applications of Color Modes
for Image Creation ........................................ 45
●BT.2020 ......................................................... 46
●BT.70 9 ............................................................47
●DCI-P3 .......................................................... 48
●PQ _ BT. 210 0 .................................................. 49
●PQ_DCI-P3................................................... 50
●H LG _ BT. 210 0.................................................51
7-2. Setting Procedure....................................... 52
●List of Setting Items....................................... 55
7-3. Settings with ColorNavigator 7 ................. 56
●Setting Procedure ......................................... 56
●Target Settings of ColorNavigator 7.............. 56
Chapter 8 Troubleshooting.............................. 58
8-1. No Picture .................................................... 58
8-2. Imaging Problems....................................... 59
8-3. SelfCalibration Problems........................... 60
8-4. Other Problems............................................61
Chapter 9 Reference ........................................ 62
9-1. Attaching the Installation Fixture ............. 62
9-2. Connecting Multiple External Devices..... 64
9-3. Making Use of the USB Hub Function ...... 65
●Connection Procedure .................................. 65
9-4. Specications ............................................. 66
●Accessories....................................................67
Appendix.............................................................. 68
Trademark ............................................................... 68
License .................................................................... 68
Warning for Radio interference............................ 69

Chapter 1 Introduction
This chapter describes the features of the monitor and the name of each control.
1-1. Features
●Large built-in high resolution 4K LCD that is advantageous for
video production
• 31.1-inch widescreen monitor with support for DCI 4K resolution (4096 × 2160)
Supports the digital cinema standard for DCI 4K resolution of 4096 × 2160. In addition to 4K videos,
which have a high resolution that is more than 4x greater than full HD, multiple full HD videos can
be displayed at the same time.
• Faithful reproduction of video colors with a wide color gamut display
99 % of DCI is covered, for a highly accurate color management environment.
• Achieves a contrast ratio of 1,000,000:1*1
A high contrast ratio allows black to be displayed in a rmer tone.
*1 Standard value. Not a guaranteed value.
• Built-in IPS LCD panel with 178° horizontal and vertical wide viewing angles
●Support for HDR (High Dynamic Range) video
• Complies with the international HDR standards for movies and broadcasts
Supports both the HDR "PQ format" for streaming and movie production, and the HDR "Hybrid Log
Gamma format" for broadcasts. The "PQ format" complies with the ITU-R BT.2100*2 and SMPTE
ST2084*3 international HDR standards, and the "Hybrid Log Gamma format" complies with the
ITU-R BT.2100 international HDR standard. This makes it possible to use the monitor for the color
grading of a wide range of HDR content, such as movies and broadcasts.
*2 ITU-R is the International Telecommunication Union-Radio communication Sector.
*3 SMPTE is the Society of Motion Picture and Television Engineers.
• High brightness and high contrast ratio
High brightness and a high contrast ratio are achieved by installing a dedicated IPS LCD panel and
a dedicated backlight unit with a high level of brightness.
• Built-in color mode function
Reproduces a color temperature, gamma, and color gamut compliant with ITU-R BT.2100 and other
standards.
See “Color Mode” (page 20).
●Support for SDI signal input or output for long-distance
transmissions
• Built-in SDI input terminals
This monitor is equipped with one SDI input terminal that supports up to 12G-SDI signals, and three
SDI input terminals that support up to 3G-SDI signals.
• Built-in SDI output terminals that support through-out (active)
6Chapter 1 Introduction

●Built-in mode for automatically switching to the optimal color
settings
• Color Mode "SYNC_SIGNAL"
This monitor is equipped with a color mode (SYNC_SIGNAL) so you can automatically set the
optimal values for the color settings of the monitor according to the input signal. If you use this
mode, the color settings of the monitor automatically switch to the optimal color settings for
HDR when the input signal is switched from SDR to HDR, so setting the colors manually is not
necessary.
●Various functions that support color grading work
• Dedicated video production functions, such as a Gamut Warning function and a Luminance
Warning function
See “Chapter 3 Advanced Adjustments/Settings” (page 15).
• 4K Zoom function
When a 4K2K signal (a signal with a resolution of 4096 × 2160 or 3840 × 2160) is displayed on the
monitor, the specied area can be doubled in size. This is convenient for checking details in an
image.
See “Zoom” (page 28).
• User-dened custom key function
Work e󰀩ciency can be improved by assigning frequently used functions to the buttons on the front
of the monitor.
See “Chapter 5 Custom Key Settings” (page 40).
• Quick Check function
Use the Quick Check function to check signals for which you can temporarily change the
brightness, gamma, or other settings.
• Displays HDCP (High Bandwidth Digital Protection) protected content
• Monitor hood included as standard
Includes a monitor hood that e󰀨ectively prevents reections from external light, such as the
reected glare of a light. The monitor hood uses magnets for easy attachment and removal.
• SelfCalibration function
The built-in calibration sensor enables the monitor to calibrate itself by using SelfCalibration.
See “Chapter 4 SelfCalibration” (page 35).
●Equipped with a USB Hub function
• Supports USB 3.1 Gen 1
Achieves high-speed data transfers of up to 5 Gbps, which enables transfers of large amounts of
data to and from USB memory devices in a short amount time.
Also, the USB downstream port supports quick charging, so you can recharge your
smartphone or tablet in a short period of time.
See “9-3. Making Use of the USB Hub Function” (page 65) and “USB CHARGE Port” (page
31).
7
Chapter 1 Introduction

1-2. Controls and Functions
●Front
1
2 3 4 5 6 7 8 9 10
(When sensor is operating)
1. Built-in calibration sensor Executes calibration for monitors.
By executing SelfCalibration, the calibration sensor automatically
operates and regularly calibrates the monitor (page 35).
2. (SIGNAL) button Switches the input signal.
3. (MODE) button Switches the color mode.
4. (S-GAMMA (F1)) button The function assigned to the button is executed.
The indicator color di󰀨ers depending on the function settings.
Blue : The Quick Check function is enabled
White : The Quick Check function is disabled
OFF : A function other than the Quick Check function is
assigned
5. (EOTF (F2)) button
6. (BRIGHT (F3)) button
7. (BLACK (F4)) button
8. Dial Turn the dial to the left or right to select items on the Setting menu
and adjust the setting values.
The Setting menu appears when you press the dial. Press the dial to
conrm the settings after you are nished.
9. (EXIT) button Returns to the previous screen.
10. Power button Turns the power on or o󰀨.
The indicator is lit when you turn the power on.
The indicator color di󰀨ers depending on the monitor's operation
status.
White : Normal operating mode
Orange : Power saving mode
OFF : Power o󰀨
8Chapter 1 Introduction

●Rear
14
15
19
20
18
21
17
12
1313 16
11
23
22
24
11. Transportation handle This handle is used for transportation.
Attention
• With help from one other person, rmly grasp and hold the monitor
by the bottom while grabbing the handle, and carefully convey the
monitor so as not to drop it.
12. Security lock slot Complies with Kensington's MicroSaver security system.
13. Stand The height and angle cannot be adjusted.
14. Main power switch Turns the main power on or o󰀨.
: On : O󰀨
15. Power connector Connects the power cord.
16. Cable holder Covers the monitor cables.
Attention
• Do not hold the monitor by the cable holder when transporting the
monitor. The cable holder may be damaged, or this may result in
other injury or damage.
17. SDI output terminal (BNC) The signal input to the SDI input terminal is output.
SDI 1 supports 12G/6G/3G/HD-SDI.
SDI 2, SDI 3, and SDI 4 support 3G/HD-SDI.
Attention
• This product supports through-out (active). When outputting the
signal, turn the main power of the monitor on.
18. SDI input terminal (BNC) Connects to a device that has SDI output.
SDI 1 supports 12G/6G/3G/HD-SDI.
SDI 2, SDI 3, and SDI 4 support 3G/HD-SDI.
9
Chapter 1 Introduction

19. USB Type-A connector (USB
downstream port, supports
quick charging)
Connects to a peripheral USB device (page 31).
20. USB Type-A connector
(USB downstream port)
Connects to a peripheral USB device.
21. USB Type-B connector
(USB upstream port)
Connects to the USB cable when using software that requires a USB
connection, or when using the USB Hub function (page 65).
22. DisplayPort connector Connects to an external device that has DisplayPort output.
23. HDMI connector Connects to an external device that has HDMI output.
24. Opening for HDMI cable xing
clamp
This is used to x the HDMI cable clamp in place.
10 Chapter 1 Introduction

Chapter 2 Basic Adjustments/Settings
This chapter describes the basic functions that can be set by pressing the buttons on the front of the monitor.
For advanced adjustment and setting procedures using the Setting menu, see “Chapter 3 Advanced
Adjustments/Settings” (page 15).
2-1. Switching Input Signals
When a monitor has multiple signal inputs, the signal to display on-screen can be changed.
Press the (SIGNAL) button to display the menu for selection of the input signal.
Turn the dial to select the input signal that you want to display, and then press the dial to conrm the
settings.
2-2. Switching the Display Mode (color mode)
This function allows easy selection of a display mode according to monitor application.
Press the (MODE) button to display the menu for selection of the color mode.
Turn the dial to select the color mode that you want to display, and then press the dial to conrm the
settings.
11
Chapter 2 Basic Adjustments/Settings

●Display Modes
Color Mode Purpose
Standard Mode Adjust color using the monitor's Setting menu.
BT.2020 See “Color Mode Setting Values” (page 13) for detailed setting values
for each color mode.
BT.70 9
DCI-P3
PQ _ BT. 210 0
PQ_DCI-P3
H LG _ BT. 210 0
SYNC_SIGNAL
Advanced Mode Adjusts the monitor’s display using the monitor’s SelfCalibration function
or color management software "ColorNavigator 7".
CAL1 Displays the screen adjusted by SelfCalibration or ColorNavigator 7.
CAL2
CAL3
Note
• If you switch between SDR color modes (BT.2020, BT.709, and DCI-P3) and HDR color modes (PQ_BT.2100,
PQ_DCI-P3, and HLG_BT.2100), wait 30 minutes or more after switching the color modes, and then adjust
the monitor.
12 Chapter 2 Basic Adjustments/Settings

●Color Mode Setting Values
-: Cannot be changed
Item
Color Mode
BT.2020 BT.709 DCI-P3
PQ_
BT.2100
PQ_
DCI-P3
HLG_
BT.2100
CAL1 /
CAL2 /
CAL3
SYNC_
SIGNAL
Brightness (cd/m2)100 100 48 1000 1000 1000 -100*1
Temperature D65 D65 D65 D65 D65 D65 -D65
Gamma (EOTF) 2.4 2.4 2.6 PQ PQ HLG -2.4*1
PQ Option ---1000
cd/m2
Clipping
1000
cd/m2
Clipping
- - -
HLG System Gamma -----1.2 - -
Color Gamut BT.2020 BT.709 DCI BT.2020 DCI BT.2020 -BT.709*1
Advanced Settings
Hue 000000- 0
Saturation 000000- 0
Gamut Clipping On On On On On On -On
XYZ Format - - O󰀨 -O󰀨 - - -
Gain
Red Calculated from color temperature - Calculated
from color
temperature
Green -
Blue -
Black Level
All 000000- 0
Red 000000- 0
Green 000000- 0
Blue 000000- 0
6 Colors Magenta
Hue 000000- 0
Saturation 000000- 0
Lightness 000000- 0
Red
Hue 000000- 0
Saturation 000000- 0
Lightness 000000- 0
Yellow
Hue 000000- 0
Saturation 000000- 0
Lightness 000000- 0
Green
Hue 000000- 0
Saturation 000000- 0
Lightness 000000- 0
Cyan
Hue 000000- 0
Saturation 000000- 0
Lightness 000000- 0
Blue
Hue 000000- 0
Saturation 000000- 0
Lightness 000000- 0
*1 This is set automatically according to the input signal. If the value cannot be retrieved from the input
signal, the value shown in the table is set.
13
Chapter 2 Basic Adjustments/Settings

Note
• Use ColorNavigator 7 to set CAL1 / CAL2 / CAL3. These settings cannot be changed in the Setting menu on the
monitor.
• A color mode can be set for each input signal.
• See “Color” (page 19) for details about each item.
• You can disable specic mode selections. For more information, see “Mode Skip” (page 32).
2-3. Using the Quick Check Function
This function is for temporarily changing the HLG System Gamma, Gamma (EOTF), Brightness, and
Black Level Lift.
1.
Executing Quick Check
1. Press the button for an item you want to check (HLG System Gamma: , Gamma (EOTF): ,
Brightness: , Black Level Lift: ) to change the setting value temporarily.
The Quick Check function is executed.
2.
Setting
1. Use the buttons to adjust/set the selected item, and then press the dial to conrm the settings.
The setting value will be changed temporarily.
Note
• When the button for (S-GAMMA), (EOTF), (BRIGHT), or (BLACK) is lit up in blue, the
Quick Check function is being executed.
3.
Exiting Quick Check
1. Press the button for (S-GAMMA), (EOTF), (BRIGHT), or (BLACK) that is lit up
in blue.
The setting value returns to the state prior to making changes.
Note
• Quick Check can also be exited using the following operations:
- Turn the power on or o󰀨 using the main power switch or power button
- Switch the input signal or color mode
- Execute "Reset" in the "Color" menu
- Execute "Monitor Reset" in the "Preferences" menu
-Execute SelfCalibration
- Start ColorNavigator 7
- Change the assignment of the custom key to a function other than Quick Check (see “5-2. Assigning a
Function to a Custom Key” (page 40))
- Change the HLG System Gamma, Gamma (EOTF), Brightness, or Black Level Lift in the Setting menu
14 Chapter 2 Basic Adjustments/Settings

Chapter 3 Advanced Adjustments/Settings
This chapter describes the advanced monitor adjustment and setting procedures using the Setting menu.
For the basic setting functions using the buttons on the front of the monitor, see “Chapter 2 Basic
Adjustments/Settings” (page 11).
3-1. Basic Operation of the Setting Menu
1.
Menu display
1. Press the dial.
The Setting menu appears.
2.
Adjusting/setting
1. Turn the dial to choose a menu to adjust/set, and then press the dial.
The Sub menu appears.
15
Chapter 3 Advanced Adjustments/Settings

2. Turn the dial to choose an item to adjust/set, and then press the dial.
The Adjustment/Setting menu appears.
3. Turn the dial to adjust/set the selected item, and then press the dial to conrm the settings.
The Sub menu appears.
Pressing the (EXIT) button during adjustment/setting will cancel the adjustment/setting and restore the
state prior to making changes.
3.
Exiting
1. Press the (EXIT) button.
The Setting menu appears.
2. Press the (EXIT) button.
The Setting menu exits.
16 Chapter 3 Advanced Adjustments/Settings

3-2. Setting Menu Functions
●Signal
The signal settings are used to congure advanced settings for input signals, such as the color format
and input range.
Function Settings Description
Signal Information - You can check the information for the input signal. The
information displayed may di󰀨er depending on the input signal.
• SDI
• DisplayPort
• HDMI
17
Chapter 3 Advanced Adjustments/Settings

Function Settings Description
Input Color Format Auto
YUV 4:2:2*1
YUV 4:4:4*1
YUV*2
RGB*1 *2
YCC4:2:2 10bit*3
YCC4:2:2 12bit*3
YCC4:4:4 10bit*3
YCC4:4:4 12bit*3
RGB4:4:4 10bit*3
RGB4:4:4 12bit*3
The color space of the input signal can be specied.
Try changing this setting if colors are not displayed correctly.
Normally, select "Auto". When an SDI signal is input, the bit
depth is specied using the Input Color Format. If the specied
bit depth is invalid, a signal error is displayed.
*1 Only enabled during HDMI input
*2 Only enabled during DisplayPort input
*3 Only enabled during SDI input. To apply the settings to the input signal, you must press the dial to conrm
the settings.
Function Settings Description
YUV Color Matrix Auto
BT.601
BT.70 9
BT.2020
Select the YUV format of the input signal. Use this setting for
gradation collapse or other occurrences where the screen is
displayed incorrectly because of a problem with the input signal.
Input Range Auto
Full
Limited (109%
White)
Limited
SDI Full
Depending on the external device, the black and white levels in the
video signal output to the monitor may be restricted. If the signal
is displayed on the monitor in its restricted form, the blacks will be
faint, the whites dull, and contrast will be reduced. The brightness
range of such signals can be extended to match the actual contrast
ratio of the monitor.
• "Auto"
The monitor automatically recognizes the brightness range of
input signals and displays images appropriately.
• "Full"
The input signal brightness range is not extended.
• "Limited (109% White)"
The brightness range of the input signal is extended from 16 -
254 (10 bits: 64 - 1019) to 0 - 255 (10 bits: 0 - 1023) for display.
• "Limited"
The brightness range of the input signal is extended from 16 -
235 (10 bits: 64 - 940) to 0 - 255 (10 bits: 0 - 1023) for display.
• "SDI Full"
The brightness range of the input signal is extended from 1 - 254
(10 bits: 4 - 1019) to 0 - 255 (10 bits: 0 - 1023) for display.
Black Level Lift -500 to 500 The black video level is changed without changing the white video
level of the input signal.
Deinterlacing Normal
Line Doubler
Select the IP conversion format. Normally, it is not necessary to
change this setting from "Normal".
18 Chapter 3 Advanced Adjustments/Settings

Function Settings Description
SDI
Settings
Time Code
Settings
Time Code
Format
Position
Size
The time code can be set.
• Time Code
If this function is set to "On", the time code is displayed.
• Format
You can choose either "VITC" or "LTC" for the format of the time
code.
• Position
You can choose either "Top" or "Bottom" for the position to
display the time code.
• Size
You can choose either "Small" or "Large" for the size of the time
code.
Interlace / PsF Auto
Interlace
PsF
When an SDI signal other than progressive is input, the display
format can be set.
●Color
The setting details di󰀨er depending on the color mode selected.
When the color mode is Standard Mode (BT.2020 / BT.709 / DCI-P3 / PQ_BT.2100 /
PQ_DCI-P3 / HLG_BT.2100 / SYNC_SIGNAL)
Each color mode setting can be adjusted according to personal preference.
Attention
• The same image may be seen in di󰀨erent colors on multiple monitors due to di󰀨erences between individual
monitors. Make ne color adjustment visually when matching colors on multiple monitors.
Note
• If "Color Mode" is "SYNC_SIGNAL", the "Brightness", "Gamma (EOTF)", and "Color Gamut" are automatically
set according to the input signal and cannot be changed.
• Use the values shown in "cd/m2" and "K" as a guide only.
19
Chapter 3 Advanced Adjustments/Settings

Function Settings Description
Color Mode BT.2020
BT.70 9
DCI-P3
PQ_ BT.210 0
PQ_DCI-P3
H LG _ BT. 210 0
CAL1
CAL2
CAL3
SYNC_SIGNAL
Switch to the desired mode according to the monitor application.
Note
• For more information on how to switch modes, see “2-2. Switching
the Display Mode (color mode)” (page 11).
• Regarding "CAL1 / CAL2 / CAL3" see page 24.
Brightness
48 cd/m2to
1000 cd/m2
The screen brightness is adjusted by changing the brightness of the
backlight (light source from the LCD back panel).
Note
• If a value that cannot be set is selected, the value will appear in
magenta. In such a case, change the value.
• 48 cd/m2 to 300 cd/m2 can be set in increments of 1, and 300 cd/
m2 to 1000 cd/m2 can be set in increments of 100.
Temperature Native
4000 K to
10000 K
D50
D65
D65 (CRT)
DCI
User
The color temperature can be adjusted.
The color temperature is used to express the chromaticity of "White".
The value is expressed in degrees "K" (Kelvin).
The screen becomes reddish at a low color temperature, and bluish
at a high color temperature, like the temperature of a ame.
Specify a color temperature in units of 100 K, or select a standard
name.
Note
• Select "Native" to display the original colors of the LCD panel.
• "Gain" allows you to perform more advanced adjustment. When
gain is changed, the color temperature is changed to "User".
• The gain preset values are set for each color temperature setting
value
.
Gamma (EOTF) 1.6 to 2.7
sRGB
EBU(2.35)
PQ
HLG
Adjust the gamma.
The brightness of the monitor varies depending on the input signal,
however, the variation rate is not simply proportional to the input
signal. The control performed to keep the balance between the
input signal and the brightness of the monitor is called "Gamma
correction".
Set the gamma, or select a standard name.
Note
• If you select "HLG", you must set "HLG System Gamma".
20 Chapter 3 Advanced Adjustments/Settings