Eizo ColorEdge CG319X User manual

Important
Please read this “User’s Manual”, and “PRECAUTIONS” (separate
volume) carefully to familiarize yourself with safe and effective usage.
•Refer to the “Setup Guide” for information on the installation /
connection of the monitor.
•For the latest product information including the “User’s Manual”,
refer to our web site :
http://www.eizoglobal.com
Color Management LCD Monitor
User’s Manual
Thank you for purchasing our Color Management LCD Monitor.

2
Location of Caution Statement
This product has been adjusted specically for use in the region to which it was originally shipped. If
operated outside this region, the product may not perform as stated in the specications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information condential unless
prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every
effort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specications are subject to change without notice.

3
Notice for This Monitor
Notice for This Monitor
About the Usage of This Product
This product is suited for producing videos, where accurate color reproduction is a priority.
This product has been adjusted specically for use in the region to which it was originally shipped. If the
product is used outside the region, it may not operate as specied in the specications.
This product may not be covered by warranty for uses other than those described in this manual.
The specications noted in this manual are only applicable when the following are used:
• Power cords provided with the product
• Signal cables specied by us
Only use optional products manufactured or specied by us with this product.
About the LCD Panel
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may
appear on the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994 % or higher.
It takes about 3 minutes (under our measurement conditions) for the monitor display to stabilize. Please wait
3 minutes or more after the monitor power has been turned on, and then adjust the monitor.
Monitors should be set to a lower brightness to prevent a loss in the screen quality caused by long-term use
and to maintain stable use.
When the screen image is changed after displaying the same image for extended periods of time, an
afterimage may appear. Use the screen saver or power save function to avoid displaying the same image for
extended periods of time. Depending on the image, an afterimage may appear even if it was displayed for
a short period of time. To remove such a phenomenon, change the image or keep the power turned off for
several hours.
If the monitor displays continuously over a long period of time, smudges or burn-in may appear. To maximize
the life of the monitor, we recommend the monitor be turned off periodically. Use the power switch on the
front of the monitor to turn it off.
The backlight of the LCD panel has a xed lifetime. Depending on the usage pattern, such as usage for
long continuous periods, the lifespan of the backlight may run out sooner, requiring replacement. When the
screen becomes dark or begins to icker, please contact your local EIZO representative.
Do not press on the LCD panel or edge of the frame strongly, as this may result in display malfunctions, such
as interference patterns, etc. If pressure is continuously applied to the LCD panel surface, the liquid crystal
may deteriorate or the LCD panel may be damaged. (If the pressure marks remain on the panel, leave the
monitor with a black or white screen. The symptom may disappear.)
Do not scratch or press on the LCD panel with any sharp objects, as this may result in damage to the LCD
panel. Do not attempt to brush with tissues as this may scratch the panel.

4Notice for This Monitor
About the Installation
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew
condensation may occur on the interior and exterior surfaces of the monitor. In that case, do not turn the
monitor on. Instead wait until the dew condensation disappears, otherwise it may cause some damage to the
monitor.
If you place this product on a lacquer-coated desk, the color may adhere to the bottom of the stand due to
the composition of the rubber. Check the desk surface before use.
About the Maintenance
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime.
Cleaning
The stains on the cabinet and LCD panel surface can be removed by using the provided ScreenCleaner.
Attention
• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet
or LCD panel, and also quality deterioration of the image.
• Never use thinner, benzine, wax, or abrasive cleaner as they may damage the cabinet or LCD panel surface.
To Use the Monitor Comfortably
• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor
according to the environmental conditions.
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.

5
Contents
Contents
Notice for This Monitor......................................... 3
Cleaning .................................................................... 4
To Use the Monitor Comfortably ............................ 4
Contents................................................................. 5
Chapter 1 Introduction....................................... 6
1-1. Features ......................................................... 6
●Large built-in high resolution 4K LCD
that is advantageous for video production...... 6
●Support for HDR (High Dynamic Range)
video................................................................ 6
●User-dened custom key function................... 6
●SelfCalibration function................................... 7
1-2. Controls and Functions ............................... 8
●Front ................................................................ 8
●Rear................................................................. 9
1-3. Setting the Resolution ................................10
●Windows 10....................................................10
●Windows 8.1 / Windows 7 ..............................10
●OS X Mavericks (10.9) or higher ....................10
Chapter 2 Basic Adjustments/Settings.......... 11
2-1. Switch Operation Method ...........................11
●Operation Guide Icons ...................................11
2-2. Switching Input Signals ..............................12
2-3. Switching the Display Mode (color
mode).............................................................12
●Display Modes................................................12
●Color Mode Setting Values ............................13
Chapter 3 SelfCalibration ................................ 14
●SelfCalibration functions ................................15
3-1. Setting targets..............................................17
3-2. Executing ......................................................17
●Executing regardless of a schedule...............17
●Executing by setting a schedule ....................17
●Activating SelfCalibration in Standard
Mode ..............................................................17
●Activating SelfCalibration in Calibration
Mode (CAL mode) ..........................................18
3-3. Checking results..........................................18
Chapter 4 Custom Key Settings...................... 19
4-1. Basic Operation of the Custom Keys ........19
4-2. Assigning a Function to a Custom Key.....19
●Functions that can be Assigned to
Custom Keys ..................................................21
Chapter 5 Advanced Adjustments/
Settings............................................ 22
5-1. Basic Operation of the Setting Menu ....... 22
5-2. Setting Menu Functions ............................. 23
●Signal ............................................................ 23
●Color.............................................................. 25
●SelfCalibration............................................... 30
●Screen ............................................................31
●Preferences................................................... 36
●Languages .................................................... 38
●Information .................................................... 38
Chapter 6 Administrator Settings................... 39
6-1. Basic Operation of the "Administrator
Settings" Menu............................................ 39
6-2. "Administrator Settings" Menu
Functions ..................................................... 40
Chapter 7 Troubleshooting.............................. 42
7-1. No Picture .................................................... 42
7-2. Imaging Problems....................................... 43
7-3. SelfCalibration Problems........................... 44
7-4. Other Problems........................................... 45
Chapter 8 Reference ........................................ 46
8-1. Attaching the Optional Arm....................... 46
8-2. Attaching/Detaching the Cable Holder .... 48
8-3. Connecting Multiple External Devices..... 50
8-4. Making Use of the USB Hub Function .......51
●Connection Procedure ...................................51
8-5. Specications ............................................. 53
●Accessories................................................... 54
Appendix.............................................................. 55
Trademark ............................................................... 55
License .................................................................... 55
FCC Declaration of Conformity ............................ 56

6Chapter 1 Introduction
Chapter 1 Introduction
This chapter describes the features of the monitor and the name of each control.
1-1. Features
●Large built-in high resolution 4K LCD that is advantageous for
video production
• 31.1-inch widescreen monitor with support for DCI 4K resolution (4096 × 2160)
Supports the digital cinema standard for DCI 4K resolution of 4096 × 2160. In addition to 4K videos,
which have a high resolution that is more than 4x greater than full HD, multiple full HD videos can
be displayed at the same time.
• Faithful reproduction of video colors with a wide color gamut display
98 % of DCI is covered, for a highly accurate color management environment.
• Built-in IPS LCD panel with 178° horizontal and vertical wide viewing angles
●Support for HDR (High Dynamic Range) video
• Complies with the international HDR standards for movies and broadcasts
Supports both the HDR "PQ format" for streaming and movie production, and the HDR "Hybrid
Log Gamma format" for broadcasts. The "PQ format" complies with the ITU-R BT.2100*1 and
SMPTE ST2084*2 international HDR standards, and the "Hybrid Log Gamma format" complies with
the ITU-R BT.2100 international HDR standard. This makes it possible to use the monitor for the
creation of a wide range of HDR content, such as movies and broadcasts.
*1 ITU-R is the International Telecommunication Union-Radio communication Sector.
*2 SMPTE is the Society of Motion Picture and Television Engineers.
• Built-in color mode function
Reproduces a color temperature, gamma, and color gamut compliant with ITU-R BT.2100 and other
standards.
See “Color Mode” (page 25).
●User-denedcustomkeyfunction
• Work efciency can be improved by assigning frequently used functions to the switches on the front
of the monitor. The functions that can be assigned to custom keys are the following:
- Input range
- Zoom
- REC709 Gamut Warning
- Luminance Warning
- Safe Area Marker
- Aspect Marker
- Prev. Color Mode
- Information
See “Chapter 4 Custom Key Settings” (page 19)

7
Chapter 1 Introduction
●SelfCalibration function
• The built-in calibration sensor enables the monitor to calibrate itself by using SelfCalibration.
By setting the calibration targets and execution schedule in advance, the calibration sensor
automatically operates and regularly calibrates the monitor. This function can be used with
Color Management Software "ColorNavigator 6" or "ColorNavigator NX" to calibrate monitor
characteristics and generate color proles.
You can set the calibration targets and execution schedule by using software (ColorNavigator 6 or
ColorNavigator NX) or the monitor's Setting menu.
You can check for the result of the SelfCalibration adjustment by using the monitor's Color menu.
See “Chapter 3 SelfCalibration” (page 14)
Attention
Be careful of the following points when using the built-in calibration sensor.
Do not touch the built-in calibration sensor.
It may reduce the measurement accuracy of the built-in calibration sensor, or result in
injury or equipment damage.
Attention
• A high temperature or high humidity environment may affect the measurement accuracy of the built-in
calibration sensor.
Avoid storing or using the sensor where it may be exposed to direct sunlight.
• Since the measurement result for the built-in calibration sensor may be affected, ensure that the level of
ambient light that enters the receiver part of the built-in calibration sensor does not change signicantly
during measuring.
- The use of a monitor hood is recommended.
- While measuring, do not bring your face or any objects close to the monitor, do not look into the
sensor.
- Set the monitor in the environment so that external light does not enter the sensor directly.

8Chapter 1 Introduction
1-2. Controls and Functions
●Front
1
432
1. Built-in calibration sensor Executes calibration for monitors. (SelfCalibration function)
2. Ambient light sensor Measures ambient light.
3. Operation switches Displays menus. Operate the switches according to the operation
guide.
Touch the switch to display its menu.
The switch indicators are lit white when you turn on the power.
4. Power switch Turns the power on or off.
Touch the switch to turn the power on.
The switch indicator is lit when you turn the power on. The indicator
color differs depending on the monitor's operation status.
White : Operating mode
Orange : Power saving mode
OFF : Power off
*1 See “5-1. Basic Operation of the Setting Menu” (page 22) for more information about how to use the
Setting menu.
Setting menu *1

9
Chapter 1 Introduction
●Rear
6
8
7
5
1110 1312
9
5. Transportation handle This handle is used for transportation.
Attention
• Firmly grasp and hold the monitor by the bottom while grabbing the
handle, and carefully convey the monitor so as not to drop it. Do not
hold the sensor section on the front side of the monitor.
6. USB downstream port Connects to a peripheral USB device.
port supports quick recharging.
7. Security lock slot Complies with Kensington's MicroSaver security system.
8. Stand*2 Adjusts the height and angle (tilt and swivel) of the monitor.
9. Cable holder Covers the monitor cables.
10. Main power switch Turns the main power on or off. : On, : Off
11. Power connector Connects the power cord.
12. Input signal connectors The following input connectors are located on the monitor rear in order
of left to right.
HDMI connector 1
HDMI connector 2
DisplayPort connector 1
DisplayPort connector 2
13. USB upstream port Connects to the USB cable when using software that requires a USB
connection, or when using the USB Hub function.
*2 An optional arm (or an optional stand) can be attached by removing the stand section.

10 Chapter 1 Introduction
1-3. Setting the Resolution
If the resolution is incorrect after connecting the monitor to a PC or if you want to change the resolution,
follow the procedure below.
●Windows 10
1. Right-click anywhere on the desktop except for on icons.
2. From the displayed menu, click "Display Settings".
3. In the "Customize your display" dialog box, click "Advanced display settings".
4. Select the monitor, and select the resolution from the "Resolution" pull-down menu.
5. Click "Apply".
6. When a conrmation dialog box appears, click "Keep changes".
●Windows 8.1 / Windows 7
1. For Windows 8.1, click the "Desktop" tile on the Start Screen to display the desktop.
2. Click the right mouse button anywhere on the desktop except for on icons.
3. From the displayed menu, click "Screen resolution".
4. Select the monitor in the "Screen Resolution" dialog box.
5. Click "Resolution", and select the resolution you want to change.
6. After selecting the resolution, click "OK".
7. When a conrmation dialog box is displayed, click "Keep changes".
Note
• When changing the size of the characters or other items that are displayed, select "Display" from the
control panel and change the scaling level.
●OS X Mavericks (10.9) or higher
1. Select "System Preferences" from the Apple menu.
2. When the "System Preferences" dialog box is displayed, click "Displays".
3. In the displayed dialog box, select the "Display" tab and click "Scaled".
4. Select the resolution you want to change from the list of possible resolution settings.
If the target resolution is not displayed in the list, press and hold the Option key on the keyboard
and select "Scaled".
5. Your selection will be reected immediately. When you are satised with the selected resolution,
close the window.

11
Chapter 2 Basic Adjustments/Settings
Chapter 2 Basic Adjustments/Settings
This chapter describes the basic functions that can be set by touching the switches on the front of the
monitor.
For advanced adjustment and setting procedures using the Setting menu, see “Chapter 5 Advanced
Adjustments/Settings” (page 22).
2-1. Switch Operation Method
1.
Displaying the operation guide
1. Touch any switch (except ).
The operation guide appears on the screen.
2.
Setting
1. Touch a switch for setting.
The Setting menu appears.
2. Use the switches to adjust/set the selected item, and then select to conrm.
3.
Exiting
1. Select to exit the menu.
2. When no menu is displayed, the operation guide will automatically disappear after a few seconds
if no switches are operated.
Note
• The contents of the guide will differ depending on the selected menu or status.
●Operation Guide Icons
Icon Description
Switches the input signal.
Switches the color mode.
Executes the function assigned to Custom Key 1.
Executes the function assigned to Custom Key 2.
Displays the Setting menu.
Returns to the previous screen.
Moves the cursor.
Executes the selected operation.
Turns the monitor's power on or off.

12 Chapter 2 Basic Adjustments/Settings
2-2. Switching Input Signals
When a monitor has multiple signal inputs, the signal to display on-screen can be changed.
2-3. Switching the Display Mode (color mode)
This function allows easy selection of a display mode according to monitor application.
●Display Modes
Color Mode Purpose
Standard Mode Adjust color using the monitor's Setting menu.
REC2020 See “Color Mode Setting Values” (page 13) for detailed setting values
for each color mode.
REC709
DCI
PQ_DCI
PQ_REC2100
HLG_REC2100
Adobe®RGB
sRGB
Calibration Mode (CAL mode) Adjusts the monitor's color using the monitor's SelfCalibration function or
color management software "ColorNavigator 6" or "ColorNavigator NX".
CAL1 Displays the screen adjusted by SelfCalibration, ColorNavigator 6, or
ColorNavigator NX.
CAL2

13
Chapter 2 Basic Adjustments/Settings
●Color Mode Setting Values
-: Cannot be changed
Item
Color Mode
REC2020 REC709 DCI PQ_
DCI
PQ_
REC2100
HLG_
REC2100
Adobe®
RGB sRGB
CAL1 /
CAL2
Brightness (cd/m2)100 100 48 300 300 300 120 120 -
Temperature REC2020 REC709 DCI DCI REC2020 REC2020 Adobe®
RGB sRGB -
Gamma REC1886 REC1886 DCI PQ PQ HLG Adobe®
RGB sRGB -
PQ / HLG Clipping (cd/m2)- - - 1000 1000 Off -- -
HLG System Gamma - - - - - 1.2 ---
Color Gamut REC2020 REC709 DCI DCI REC2020 REC2020 Adobe®
RGB sRGB -
Advanced Settings
Hue 0 0 0 0 0 0 0 0 -
Saturation 0 0 0 0 0 0 0 0 -
Gamut Clipping On Off Off Off On On Off Off -
XYZ Format - - Off Off - - - - -
Gain
Red
Calculated from color temperature
-
Green -
Blue -
Black Level
Red 0 0 0 0 0 0 0 0 -
Green 0 0 0 0 0 0 0 0 -
Blue 0 0 0 0 0 0 0 0 -
6 Colors Magenta
Hue 0 0 0 0 0 0 0 0 -
Saturation 0 0 0 0 0 0 0 0 -
Lightness 0 0 0 0 0 0 0 0 -
Red
Hue 0 0 0 0 0 0 0 0 -
Saturation 0 0 0 0 0 0 0 0 -
Lightness 0 0 0 0 0 0 0 0 -
Yellow
Hue 0 0 0 0 0 0 0 0 -
Saturation 0 0 0 0 0 0 0 0 -
Lightness 0 0 0 0 0 0 0 0 -
Green
Hue 0 0 0 0 0 0 0 0 -
Saturation 0 0 0 0 0 0 0 0 -
Lightness 0 0 0 0 0 0 0 0 -
Cyan
Hue 0 0 0 0 0 0 0 0 -
Saturation 0 0 0 0 0 0 0 0 -
Lightness 0 0 0 0 0 0 0 0 -
Blue
Hue 0 0 0 0 0 0 0 0 -
Saturation 0 0 0 0 0 0 0 0 -
Lightness 0 0 0 0 0 0 0 0 -
Note
• Use ColorNavigator 6 or ColorNavigator NX to set CAL1 / CAL2. These settings cannot be changed in the Setting
menu on the monitor.
• A color mode can be set for each input signal.
• See “Color” (page 25) for details about each item.
• You can disable specic color mode selections. For more information, see “Mode Skip” (page 37).

14 Chapter 3 SelfCalibration
Chapter 3 SelfCalibration
This product is equipped with a built-in calibration sensor. By setting the calibration targets and execution
schedule in advance, the calibration sensor automatically operates and regularly calibrates the monitor. This
automatic calibration function is called "SelfCalibration".
The adjustment content of SelfCalibration differs depending on the color mode that is executed.
• Calibration Mode (CAL mode: CAL1 / CAL2):
- When performing SelfCalibration on the monitor itself, calibrate the monitor to match the set
targets.
- When using ColorNavigator 6 or ColorNavigator NX, use a measurement device with the
software to maintain the calibrated state of the monitor.
• Standard Mode (color mode excluding CAL1 / CAL2): the monitor's color reproduction gamut is
updated and each display mode in Standard Mode is adjusted as follows:
- The temperature is adjusted so that it is as close as possible to the specied value.
- The gamut values are adjusted so that they are close to each specied value.
- Information on brightness is updated.
Note
• SelfCalibration can be executed 30 minutes after turning on the monitor.
• SelfCalibration can also be executed when there are no external device signals being input.
• To preserve adjustments that you set by using ColorNavigator 6 or ColorNavigator NX, it is recommended to execute
SelfCalibration.
• Because brightness and chromaticity will change as you use the monitor, it is recommended to calibrate the monitor
periodically.
• The measurement results from the built-in calibration sensor can be correlated with the measurement results from
the external measurement device that you want to use as a reference. For details, refer to the User's Manual of
ColorNavigator 6 or ColorNavigator NX.
You can set the calibration targets and execution schedule by using ColorNavigator 6 or ColorNavigator NX
or the monitor's Setting menu.
You can download the ColorNavigator 6 or ColorNavigator NX software and User's Manual from our web
site:
http://www.eizoglobal.com
Note
• When using the software, you will need to connect a PC to the monitor with the supplied USB cable.
• For details on the USB cable connection, see "Connection Procedure" (page 51).
• While using the software, do not operate the power switch or operation switches on the front side of the monitor.

15
Chapter 3 SelfCalibration
●SelfCalibration functions
Set the details for "SelfCalibration".
Function Adjustable
Range Description
Execute -SelfCalibration can be executed manually
regardless of the schedule.
Note
• After selecting "Execute", warming up
(after the power to the monitor is switched
on, leaving the monitor on for a certain
period of time until the display becomes
stable) may be executed before the built-
in calibration sensor comes out.
Settings
Mode Settings Standard Mode On
Off
Switch between enabling/disabling
SelfCalibration in Standard Mode.
Calibration
Mode
CAL1
CAL2
On
Off
Switch between enabling/disabling
SelfCalibration in each color mode.
Schedule Start time Power Save
Immediately
Application
Off
Select the timing to execute SelfCalibration upon
reaching the time set in the schedule.
• "Power Save"
To be executed under any of the following
conditions.
- When the monitor is in "Power Save" mode
or power is off at the set time.
- The monitor shifts to the power saving
mode or the power is turned off when the
set time in the schedule is exceeded.
• "Immediately"
SelfCalibration is executed immediately at
the set time.
• "Application"
Execute SelfCalibration according to the
timing set using ColorNavigator Network. For
details on ColorNavigator Network, refer to
our web site (http://www.eizoglobal.com).
• "Off"
SelfCalibration is not executed.
Frequency Daily
Weekly
Monthly
Quarterly
Biannually
Annually
Usage Time
Select the SelfCalibration execution cycle.

16 Chapter 3 SelfCalibration
Function Adjustable
Range Description
Settings
Schedule Timing Jan/Apr/Jul/Oct
Feb/May/Aug/Nov
Mar/Jun/Sep/Dec
Jan/Jul
Feb/Aug
Mar/Sep
Apr/Oct
May/Nov
Jun/Dec
Jan to Dec
Every 50 hours to
Every 500 hours
When the execution cycle is "Quarterly",
"Biannually", "Annually", or "Usage Time", select
the timing for executing SelfCalibration.
The setting range differs depending on the
execution cycle setting.
• "Quarterly":
Jan/Apr/Jul/Oct, Feb/May/Aug/Nov, Mar/Jun/
Sep/Dec
• "Biannually":
Jan/Jul, Feb/Aug, Mar/Sep, Apr/Oct, May/
Nov, Jun/Dec
• "Annually":
Jan to Dec
• "Usage Time":
Every 50 hours to Every 500 hours
Week 1st week
to 5th week
When the execution cycle is "Monthly",
"Quarterly", "Biannually", or "Annually", select the
week for executing SelfCalibration.
Note
• When no day has been selected for "Day" in
the selected week, the week of execution will
be as follows:
- When the selected week is "1st week":
2nd week
- When the selected week is "5th week":
4th week
Day Sunday to
Saturday
When the execution cycle is "Weekly", "Monthly",
"Quarterly", "Biannually", or "Annually", select the
day for executing SelfCalibration.
Time 0:00 to 11:55 PM When the execution cycle is "Daily", "Weekly",
"Monthly", "Quarterly", "Biannually", or "Annually",
select the time for executing SelfCalibration.
Clock Adjustment - Set the monitor date and time.
Note
• When the clock has not been set, the
schedule will not be applied.
• If the main power supply is
disconnected for an extended period
of time, the clock may need resetting.
• When ColorNavigator 6 or
ColorNavigator NX is started, the date
and time are automatically set.
Result -The SelfCalibration execution result is displayed.
Next Calibration -The next SelfCalibration scheduled execution
date is displayed.

17
Chapter 3 SelfCalibration
3-1. Setting targets
Set calibration targets for Calibration Mode. You can set targets by using ColorNavigator 6 or
ColorNavigator NX, or on the monitor itself.
When using the monitor itself, set the following functions in the "Color" menu.
• "Color Mode"
Select the color mode (CAL mode: CAL1 / CAL2) you want to set a target for.
• "Target Settings"
Set a calibration target for SelfCalibration.
3-2. Executing
SelfCalibration can be executed by setting a schedule or it can be executed regardless of a schedule.
You can set a schedule by using ColorNavigator 6 or ColorNavigator NX, or on the monitor itself.
When executing SelfCalibration by setting a schedule on the monitor itself, the method to set the
schedule differs depending on the type of color mode (Standard Mode or Calibration Mode).
Attention
• If there is a change in the video signal from the external device during SelfCalibration (the signal disappears, a
signal is input during a no-signal state, or other), SelfCalibration is automatically canceled.
●Executing regardless of a schedule
Manually execute SelfCalibration.
There are two methods for executing SelfCalibration, as follows.
• Execute from the "SelfCalibration" menu
In the "SelfCalibration" menu, select "Execute".
SelfCalibration is executed for all the color modes selected as "On" in "Settings" - "Mode Settings" of the
"SelfCalibration" menu.
• Executing from the "Color" menu
In "Color Mode" in the "Color" menu, select the color mode (CAL mode: CAL1 / CAL2) you want to execute,
and then select "Execute Calibration".
Execute SelfCalibration for the displayed color mode.
●Executing by setting a schedule
Set the calibration schedule for SelfCalibration.
In "Settings" in the "SelfCalibration" menu, set the calibration schedule and monitor date and time for
SelfCalibration.
Attention
• If a scheduled SelfCalibration is automatically canceled, it is executed again when the monitor transitions
to the power saving mode an hour or more after cancellation or when the monitor is turned off using .
SelfCalibration can also be executed regardless of the schedule.
●Activating SelfCalibration in Standard Mode
Execute SelfCalibration in Standard Mode.
In "Settings" in the "SelfCalibration" menu, set the following functions:
• "Mode Settings"
Set "Standard Mode" to "On".

18 Chapter 3 SelfCalibration
●Activating SelfCalibration in Calibration Mode (CAL mode)
Execute SelfCalibration in Calibration Mode (CAL mode).
In "Settings" in the "SelfCalibration" menu, set the following functions:
• "Mode Settings"
Select "Calibration Mode".
• "Calibration Mode"
Select the color mode (CAL mode: CAL1 / CAL2) you want to execute, and set "On".
3-3. Checking results
Check the SelfCalibration calibration results by using the monitor.
In the "Color" menu, set the following functions:
• "Color Mode"
Select the color mode (CAL mode: CAL1 / CAL2) for which you want to check the result.
• "Result"
Check the calibration result of SelfCalibration.

19
Chapter 4 Custom Key Settings
Chapter 4 Custom Key Settings
You can assign functions to the custom keys to easily start specied functions.
This chapter describes how to operate the custom keys and how to assign functions to the custom keys.
4-1. Basic Operation of the Custom Keys
1.
Displaying the operation guide
1. Touch any switch (except ).
The operation guide appears.
2.
Execute
1. Select or .
The function assigned to or is executed.
Note
• If you touch a custom key to which no function has been assigned, the menu for assigning a function to that
custom key appears.
4-2. Assigning a Function to a Custom Key
1.
Displaying the operation guide
1. Touch any switch (except ).
The operation guide appears.
2.
Setting
1. Select .
The Setting menu appears.

20 Chapter 4 Custom Key Settings
2. Use to select "Preferences", and then select .
The Preferences menu appears.
3. Use to select "Custom Key", and then select .
The Custom Key menu appears.
4. Use to select the custom key to which you want to assign a function, and then select .
The menu for assigning a function appears.
5. Use to select the function that you want to assign, and then select .
That function is assigned to the custom key.
3.
Exiting
1. Press several times.
The Setting menu exits.