Eizo ColorEdge CX241 User manual

Important
Please read PRECAUTIONS, this User’s Manual, and the Setup Guide
(separate volume) carefully to familiarize yourself with safe and
effective usage.
• Please refer to the Setup Guide for basic information ranging from
connection of the monitor to a PC or external device to using the
monitor.
• The latest software and User’s Manual are available for download
from our web site:
http://www.eizo.com
Cover

2
Location of Caution Statement
This product has been adjusted specically for use in the region to which it was originally shipped. If operated
outside this region, the product may not perform as stated in the specications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,
electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information condential unless prior
arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every effort has been
made to ensure that this manual provides up-to-date information, please note that EIZO monitor specications are
subject to change without notice.

3
Notice for this monitor
Notice for this monitor
Aside from general purposes like creating documents, viewing multimedia content, this product is also suited to
applications such as graphics creation and digital photo processing, where accurate color reproduction is a priority.
This product has been adjusted specically for use in the region to which it was originally shipped. If the product is
used outside the region, it may not operate as specied in the specications.
This product may not be covered by warranty for uses other than those described in this manual.
The specications noted in this manual are only applicable when the following are used:
· Power cords provided with the product
· Signal cables specied by us
Only use optional products manufactured or specied by us with this product.
It takes about 7 minutes (under our measurement conditions) for the performance of electrical parts to stabilize. Please
wait 7 minutes or more after the monitor power has been turned on, and then adjust the monitor.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and maintain a
stable display.
When the screen image is changed after displaying the same image for extended periods of time, an afterimage may
appear. Use the screen saver or power save function to avoid displaying the same image for extended periods of time.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer to
“Cleaning” (page 4)).
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may appear on
the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994% or higher.
The screen may have defective pixels or a small number of light dots on the screen. This is due to the characteristics of
the panel itself, and is not a malfunction of the product.
The backlight of the LCD panel has a xed lifetime. When the screen becomes dark or begins to icker, please contact
your local EIZO representative.
Do not press on the panel or edge of the frame strongly, as this may result in display malfunctions, such as interference
patterns, etc. If pressure is continually applied to the panel, it may deteriorate or damage your panel. (If the pressure
marks remain on the panel, leave the monitor with a black or white screen. The symptom may disappear.)
Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do not attempt
to brush with tissues as this may scratch the panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation may
occur on the interior and exterior surfaces of the monitor. In that case, do not turn the monitor on. Instead wait until
the dew condensation disappears, otherwise it may cause some damage to the monitor.

4Notice for this monitor
Cleaning
Attention
• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet or panel,
and also quality deterioration of the image.
• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel..
Note
• The optional ScreenCleaner is recommended for cleaning the cabinet and panel surface.
The stains on the cabinet and panel surface can be removed by using the provided cleaning cloth.
To use the monitor comfortably
• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor according to
the environmental conditions.
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.

5
CONTENTS
CONTENTS
Cover ...................................................................... 1
Notice for this monitor ......................................... 3
Cleaning .................................................................... 4
To use the monitor comfortably............................. 4
CONTENTS............................................................. 5
Chapter 1 Introduction....................................... 7
1-1. Features ......................................................... 7
1-2. Controls and Functions ............................... 9
●Front ................................................................ 9
●Rear................................................................10
1-3. EIZO LCD Utility Disk...................................11
●Disk contents and software overview ............11
●To use ColorNavigator / ColorNavigator
Elements ........................................................11
1-4. Basic Operations and Functions ...............12
●Basic Adjustment menu operations ...............12
●Showing Button Guide ...................................13
●Functions........................................................13
Chapter 2 Adjusting Screens .......................... 15
2-1. Setting Resolution.......................................15
●Compatible Resolutions/Formats...................15
●To switch signal formats (Only for HDMI
signal input) ....................................................16
●To set the display resolution for the OS .........16
●To select screen size......................................17
2-2. Adjusting Screens .......................................19
●Digital Signal Input .........................................19
●Analog Signal Input........................................19
2-3. To select the display mode (color mode). 23
2-4. Adjusting Color ........................................... 24
●To adjust brightness .......................................24
●To adjust the temperature ............................. 25
●To adjust gamma........................................... 25
●To set color gamut......................................... 26
●To perform advanced adjustments ............... 26
2-5. ConguringMovingImagePerformance. 30
2-6. Specifying Color Space ............................. 30
2-7. Expanding Signal Output Range ...............31
●To extend the output range ............................31
●To select the range of signals to extend ........31
2-8. Setting HDMI................................................ 32
●To reduce noise............................................. 32
Chapter 3 Setting Monitor ............................... 33
3-1. Setting Adjustment Menu .......................... 33
●Selecting the Language ................................ 33
●Setting Orientation ........................................ 33
●To change adjustment menu display position33
3-2. Skipping Unused Display Modes.............. 34
3-3. Showing and Hiding the EIZO Logo ......... 34
3-4. Locking Operation Buttons ....................... 34
3-5. Changing DUE (Digital Uniformity
Equalizer) Setting ....................................... 35
3-6. Setting Signal Bandwidth .......................... 35
3-7. Reset to default ........................................... 36
●To reset the color adjustments...................... 36
●To reset all adjustments to the default
settings.......................................................... 36
Chapter 4 SelfCorrection................................. 37
4-1. Setting Calibration Details..........................37
●To set the timing for SelfCorrection ...............37
●To enable/disable SelfCorrection for
Standard Mode...............................................37
●Setting SelfCorrection Schedule................... 38
4-2. Executing SelfCorrection .......................... 38
Chapter 5 Connecting Multiple External
Devices ............................................ 39
5-1. To switch among input signals ................. 40
5-2. To set input signal selection...................... 40
5-3. Skipping Unused Input Signals................. 40
5-4. Switching USB Port Automatically............41
Chapter 6 Power Saving Functions ................ 42
6-1. Setting Power Save..................................... 42
6-2. Enabling/Disabling Automatic
Brightness Adjustment .............................. 43
6-3. Adjusting the Brightness of Indicator...... 43
6-4. Checking the Power Saving Level ............ 43
6-5. Setting DisplayPort Power Save ............... 44
Chapter 7 Troubleshooting.............................. 45
7-1. No picture .................................................... 45
7-2. Imaging problems (for both digital and
analog).......................................................... 46
7-3. Imaging problems (for digital only) .......... 46
7-4. Imaging problems (for analog only) ..........47
7-5. Other problems ........................................... 48
7-6. Built-in correction sensor and
SelfCorrection problems ........................... 49
Chapter 8 Reference ........................................ 50
8-1. Attaching the Optional Arm....................... 50
8-2. Making Use of USB (Universal Serial
Bus)................................................................51
●System Requirement......................................51
●Procedure.......................................................51
8-3. Showing Monitor Information.................... 52

6CONTENTS
●Displaying signal information .........................52
●Displaying Monitor Information ......................52
8-4. Specications ............................................. 53
Chapter 9 Glossary .......................................... 57
Appendix.............................................................. 60
Trademark ............................................................... 60
License / Copyright................................................ 60
FCC Declaration of Conformity .............................61
Hinweise zur Auswahl des richtigen
Schwenkarms für Ihren Monitor........................... 62
Hinweis zur Ergonomie : ....................................... 62
LIMITED WARRANTY............................................. 63
Recycling Information ........................................... 72
China Measures for RoHS Compliance in
ChinaRoHS...............................................................76

7
Chapter 1 Introduction
Chapter 1 Introduction
1-1. Features
• 24.0″ wide format LCD
• Wide color gamut (Adobe® RGB coverage: 99%)
• Supports a resolution of 1920 × 1200.
• IPS panel with 178˚ horizontal and vertical viewing angles
• Frame synchronization mode supported (23.75 - 30.5Hz, 47.5 - 61.0Hz)
• 3 signal input terminals (DVI-I × 1, HDMI × 1, DisplayPort × 1)
- DisplayPort connector (applicable to 8 bit and 10 bit)*1
- HDMI connector (applicable to 8 bit, 10 bit, and 12 bit)*1,*2
Can handle PC signals in HDMI input
*1 Not applicable to audio signals.
*2 The maximum screen display is 10 bits.
• Color Mode function
Reproduces a color temperature, gamma, and gamut compliant with the following standard.
-Adobe®RGB / sRGB
The Paper mode reproduces a printed paper effect on the monitor.
See “2-3. To select the display mode (color mode)” (page 23).
• Attaching the “Adjustment Certicate”, which describes the factory measurement results of the grayscale and
uniformity characteristics for each monitor
• Portrait/Landscape display available (rotate 90˚ clockwise)
• This product is equipped with a built-in correction sensor, and supports SelfCorrection in which the monitor
executes display correction independently.
See “Chapter 4 SelfCorrection” (page 37).
• The “ColorNavigator” Color Management Software enables you to calibrate monitor characteristics and
generate color proles*3
*3 The Color Management Software “ColorNavigator” is on the CD-ROM for the ColorNavigator Licensed models.
See “1-3. EIZO LCD Utility Disk” (page 11).
• Supports Photo Color Matching Software “ColorNavigator Elements”*4
This software enables you to adjust the color of the monitor easily while comparing it with a printed picture.
*4 Stored on the CD-ROM for the ColorNavigator non-licensed models. See “1-3. EIZO LCD Utility Disk” (page 11).
• Power saving function
Suppressing the power consumption reduces the carbon dioxide emissions. This product is equipped with power saving
function.
- 0 W power consumption when the main power is off
Equipped with main power switch.
When the monitor is not required, the power supply can be shut off using the main power switch.
- Auto EcoView function
The ambient light sensor on the front side of the monitor detects the environmental brightness to adjust the screen
brightness automatically and comfortably. Excessively high brightness may increase power consumption and cause
unwanted environmental effects. It may also lead to fatigue of your eyes. Use the Auto EcoView to reduce the
brightness.
See “6-2. Enabling/Disabling Automatic Brightness Adjustment” (page 43).
• Displays HDCP (High-bandwidth Digital Protection) protected contents.

8Chapter 1 Introduction
Attention
Be careful of the following points when using the built-in correction sensor.
Do not touch the built-in correction sensor.
It may reduce the measurement accuracy of the built-in correction sensor, or result in injury
or equipment damage.
Attention
• A high temperature or high humidity environment may affect the measurement accuracy of the built-in correction
sensor. We suggest storing and using the monitor under the following conditions.
- Temperature 30˚C or less
- Humidity 70% or less
Avoid storing or using the sensor where it may be exposed to direct sunlight.
• Since adjustment accuracy of the monitor by the build-in sensor may be affected, leave the level of ambient light that
enters the sensor part of the built-in sensor unchanged largely while measuring.
- The use of the monitor hood is recommended.
- While measuring, do not bring the face or the object close to the monitor, do not look into the sensor.
- Set the monitor in the environment so that the light outside does not enter the sensor part directly.
Note
• This monitor supports both portrait and landscape format. You can change the orientation of the Setting menu when
using the monitor screen in vertical display position. (see “Setting Orientation” (page 33))
• When using the monitor screen in a portrait position, the graphics board supporting portrait display is required. When
placing the monitor in a portrait position, the settings of your graphics board need to be changed. Refer to the User’s
Manual of the graphics board for details.

9
Chapter 1 Introduction
1-2. Controls and Functions
●Front
1
7 8 92 4 53
6
Adjustment menu*1
1. Built-in correction sensor Executes display correction for an independent monitor. SelfCorrection function
(page 37)
2. Ambient Light Sensor Measures ambient light.
3. button Switches input signals for display (page 40).
4. button Changes Color Mode (page 23).
5. button Cancels the setting/adjustment and exits the Adjustment menu.
6. button • Provides the menu selection as well as the adjustment and setting of a function.
• Displays the Brightness menu (page 24).
7. button Displays the Adjustment menu, determines an item on the menu screen, and saves
values adjusted (page 12).
8. button Turns the power on or off.
9. Power Indicator
Indicates the monitor’s operation status.
Blue: Operating
Flashing blue (2 times for each): Indicates that display correction is required if the
SelfCorrection schedule(page 38) is set.
Orange: Power saving mode
OFF: Main power/Power off
*1 For details, see “1-4. Basic Operations and Functions” (page 12).

10 Chapter 1 Introduction
●Rear
16
17
15
10 11 12 13 14
10. Main power switch Turns the main power on or off.
11. Power connector Connects the power cord.
12. Input signal connectors Left: DVI-I connector / Center: HDMI connector / Right: DisplayPort connector
13. USB upstream port Connects the USB cable to use the software that needs USB connection, or to use
USB hub function (page 51).
14. USB downstream port Connects a peripheral USB device.
15. Stand*2 Used to adjust the height and angle of the monitor screen.
16. Security lock slot Complies with Kensington’s MicroSaver security system.
17. Cable holder Covers the monitor cables.
*2 An optional arm (or an optional stand) can be attached by removing the stand section (see “8-1. Attaching the Optional Arm”
(page 50)).

11
Chapter 1 Introduction
1-3. EIZO LCD Utility Disk
An “EIZO LCD Utility Disk” (CD-ROM) is supplied with this product. The following table shows the disk contents
and the overview of the software programs.
●Disk contents and software overview
The disk includes application software programs for adjustment, and User’s Manual. Refer to “Readme.txt” or
the “read me” le on the disk for software startup procedures or le access procedures.
Contents Overview Windows Macintosh
A “Readme.txt” or “read me” le √ √
ColorNavigator*1 Software for calibrating monitor characteristics
and generating ICC proles (for Windows) and
Apple ColorSync proles (for Macintosh).
(A PC must be connected to the monitor with
the supplied USB cable.)
√ √
ColorNavigator Elements*2 Software for adjusting the color and brightness
of the monitor while comparing a picture
displayed on the monitor with a printed picture.
(A PC must be connected to the monitor with
the supplied USB cable.)
√ √
Screen adjustment pattern les Used when adjusting the image of the analog
signal input manually. √-
User’s Manual of this monitor (PDF le) √ √
*1 Only ColorNavigator Licensed models
*2 Only ColorNavigator Non-Licensed models
●To use ColorNavigator / ColorNavigator Elements
Attention
• A license is necessary to use ColorNavigator. If “ColorNavigator License” in the monitor information window (page 52)
is “Not Registered”, the ColorNavigator license must be purchased and registered to the monitor.
• ColorNavigator Elements can be used without a license.
Refer to the corresponding User’s Manual on the CD-ROM disk in order to install and use the software.
When using this software, you will need to connect a PC to the monitor with the supplied USB cable. For
details of the USB cable connection, see “8-2. Making Use of USB (Universal Serial Bus)” (page 51).

12 Chapter 1 Introduction
1-4. Basic Operations and Functions
●Basic Adjustment menu operations
1. Displaying Adjustment Menu
1. Press . The Adjustment menu appears.
Current mode
Menu title
Setting
Menu
Item
2.
Adjusting/Setting
1. Choose a menu to adjust/set with , , and then press .
2. Choose an item to adjust/set with , , and then press .
3. Adjust/set the selected item with , , and then press .
3.
Exiting
1. Press a few times. The Adjustment menu nishes.

13
Chapter 1 Introduction
●Showing Button Guide
When you press the front buttons (except the button), the button guide appears next to the button.
Note
• The button guide will continue to appear while the Adjustment menu or Mode menu is showing.
• The button guide is displayed differently depending on the selected menu or status.
• In CAL mode, the brightness cannot be adjusted even though the button guide is displayed above the and buttons.
●Functions
The following table shows the menus for adjustment and setting items of each menu.
Main Menu Item Reference
Color*1 Brightness “2-4. Adjusting Color” (page 24)
Temperature
Gamma
Color Gamut
Advanced
Settings
Hue
Saturation
Clipping
Gain
6 Colors
Color Reset “3-7. Reset to default” (page 36)
SelfCorrection Execute “4-2. Executing SelfCorrection” (page 38)
Standard Mode SelfCorrection “To enable/disable SelfCorrection for
Standard Mode” (page 37)
Schedule Starting Time “Set the timing at which SelfCorrection is
executed.” (page 37)
Interval “Setting SelfCorrection Schedule” (page 38)

14 Chapter 1 Introduction
Screen Screen Size “To select screen size” (page 17)
Overdrive “2-5. Conguring Moving Image
Performance” (page 30)
Color Space “2-6. Specifying Color Space” (page 30)
Range Extension Range Extension “2-7. Expanding Signal Output Range” (page
31)
Super White
HDMI Settings*2 Noise Reduction “2-8. Setting HDMI” (page 32)
Analog Adjustment Auto Adjustment “2-2. Adjusting Screens” (page 19)
Range Adjustment
Clock
Phase
Hor. Position
Ver. Position
Power
Manager
Power Save “6-1. Setting Power Save” (page 42)
Auto EcoView “6-2. Enabling/Disabling Automatic
Brightness Adjustment” (page 43)
Indicator “6-3. Adjusting the Brightness of Indicator”
(page 43)
EcoView Index “6-4. Checking the Power Saving Level”
(page 43)
Menu Settings Language “Selecting the Language” (page 33)
Orientation “Setting Orientation” (page 33)
Menu Position “To change adjustment menu display
position” (page 33)
Tools Input Selection “5-1. To switch among input signals” (page 40)
Input Skip “5-3. Skipping Unused Input Signals” (page
40)
Mode Skip “3-2. Skipping Unused Display Modes”
(page 34)
USB Selection “5-4. Switching USB Port Automatically”
(page 41)
Signal Info “8-3. Showing Monitor Information” (page 52)
Monitor Info
All Reset “3-7. Reset to default” (page 36)
*1 Functions available for adjustment and setting in Standard Mode (page 23) are displayed.
*2 This function is available with HDMI signal input.

15
Chapter 2 Adjusting Screens
Chapter 2 Adjusting Screens
2-1. Setting Resolution
●Compatible Resolutions/Formats
The monitor supports the following resolutions.
When using PC signal input (DVI-I, DisplayPort, HDMI: PC*1)
Resolution Vertical scan frequency
640×480 60 Hz
720×400 70 Hz
800×600 60 Hz
1024×768 60 Hz
1280×960 60 Hz
1280×1024 60 Hz
1600×1200 60 Hz
1680×1050 60 Hz
1920×1080 60 Hz
1920×1200*2 60 Hz
*1 When displaying PC signals by HDMI signal input, change the monitor’s setting in advance (see “To switch signal
formats (Only for HDMI signal input)” (page 16)).
*2 Recommended resolution
When using Video signal input
Format Vertical scan
frequency
Resolution Scan Type DVI DisplayPort
HDMI
Analog Digital Video*1 PC*2
480p 59.94 Hz / 60 Hz 640×480 Progressive -√*3 √*3 √ √*3
480i 59.94 Hz / 60 Hz 720×480 Interlace - - - √-
480p 59.94 Hz / 60 Hz 720×480 Progressive - - √*3 √-
576i 50 Hz 720×576 Interlace - - - √-
576p 50 Hz 720×576 Progressive - - - √-
720p 50 Hz 1280×720 Progressive -√*3 √*3 √ √*3
720p 59.94 Hz / 60 Hz 1280×720 Progressive -√*3 √*3 √ √*3
1080p 23.976 Hz / 24 Hz 1920×1080 Progressive -√*3 √*3 √ √*3
1080p 25 Hz 1920×1080 Progressive -√*3 √*3 √ √*3
1080p 29.97 Hz / 30 Hz 1920×1080 Progressive -√*3 √*3 √ √*3
1080i 50 Hz 1920×1080 Interlace -√*3 √*3 √ √*3
1080p 50 Hz 1920×1080 Progressive -√*3 √*3 √ √*3
1080i 59.94 Hz / 60 Hz 1920×1080 Interlace -√*3 √*3 √ √*3
1080p 59.94 Hz / 60 Hz 1920×1080 Progressive √ √*3 √*3 √ √*3
*1 The color difference signal is supported.
*2 Change the monitor’s setting in advance.
*3 The output device must be dened. Refer to the User’s Manual of the output device for further details.

16 Chapter 2 Adjusting Screens
●To switch signal formats (Only for HDMI signal input)
The monitor’s displayable resolution can be changed. Use this when displaying PC signals by HDMI signal
input.
Adjustable Range
Video / PC
Procedure
1. Press to turn off the monitor.
2. Holding down, press for at least two seconds to turn on the monitor.
The “Optional Settings” menu appears.
3. Choose “Signal Selection” from “Optional Settings”, and press .
4. Choose the input signal to set with or , and press .
5. Select “Signal Format” with the selected input signal and press .
6. Switch the signal format with or .
7. Select “Finish” with or .
8. Press .
●To set the display resolution for the OS
When you connect the monitor to the PC and nd that the resolution is improper, or when you want to change
the resolution, follow the procedure below.
Windows 8 / Windows 7
1. For Windows 8, click the “Desktop” tile on the Start Screen to display the desktop.
2. Right-click the mouse anywhere on the desktop except for icons.
3. From the displayed menu, click “Screen resolution”.
4. On the “Screen Resolution” dialog box, select the monitor.
5. Click “Resolution” to select the desired resolution.
6. Click the “OK” button.
7. When a conrmation dialog box is displayed, click “Keep changes”.
Windows Vista
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Personalize”.
3. On the “Personalization” window, click “Display Settings”.
4. On the “Display Settings” dialog box, select the “Monitor” tab and select desired resolution in the
“Resolution” eld.
5. Click the “OK” button.
6. When a conrmation dialog box is displayed, click “Yes”.
Windows XP
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Properties”.
3. When the “Display Properties” dialog box is displayed, click the “Settings” tab and select desired resolution
for “Screen resolution” under “Display”.
4. Click the “OK” button to close the dialog box.

17
Chapter 2 Adjusting Screens
Mac OS X
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” dialog box is displayed, click “Displays” for “Hardware”.
3. On the displayed dialog box, select the “Display” tab and select desired resolution in the “Resolutions” eld.
4. Your selection will be reected immediately. When you are satised with the selected resolution, close the
window.
●To select screen size
The image with the resolution other than the recommended resolution is displayed in full screen automatically.
You can change the screen size by using the “Screen Size” function from “Screen”.
When using PC signal input
Settings Function
Full Displays an image in full screen. Images are distorted in some cases because the vertical
rate is not equal to the horizontal rate.
Enlarged Displays an image in full screen. In some cases, a blank horizontal or vertical border
appears to equalize the vertical rate and the horizontal rate.
Normal Displays images with the specied resolution.
Example: Image size 1280 × 1024
Full Enlarged Normal
1920 × 1200 1500 × 1200 1280 × 1024
Procedure
1. Choose “Screen” from the Adjustment menu, and press .
2. Choose “Screen Size” from “Screen”, and press .
3. Select “Full”, “Enlarged”, or “Normal” with or .
4. Press to exit.

18 Chapter 2 Adjusting Screens
When using video signal input
●When displaying HD signals (720p, 1080i, 1080p)
Settings Function
Enlarged Images are enlarged to full screen without changing the aspect ratio. Blank borders may
appear at the top and bottom of the screen to maintain the aspect ratio.
Dot by Dot Displays images with the specied resolution.
Example: 720p
Enlarged Dot by Dot
Procedure
1. Choose “Screen” from the Adjustment menu, and press .
2. Choose “Screen Size” from “Screen”, and press .
3. Select “Enlarged”, or “Dot by Dot” with or .
4. Press to exit.
●When displaying SD signals (640x480, 480i, 480p, 576i, 576p)
Settings Function
Auto The monitor automatically changes the screen size according to the aspect ratio sent from
the auto input signal.
4:3 Displays images in a 4:3 format screen.Black bars appear on both sides of the screen.
16:9 images are horizontally compressed.
Letter Box Displays 16:9 letterboxed images in full screen.
Images other than the letterboxed ones are partly cut on top and bottom.
16:9 Displays the entire 16:9 image in full screen. Black bars appear on the top and bottom of
the screen.
4:3 images are horizontally expanded.
Example: 480i/480p (16:9)
Auto 4:3 Letter Box 16:9
Procedure
1. Choose “Screen” from the Adjustment menu, and press .
2. Choose “Screen Size” from “Screen”, and press .
3. Select “Auto”, “4:3”, “Letter Box”, or “16:9” with or .
4. Press to exit.

19
Chapter 2 Adjusting Screens
2-2. Adjusting Screens
●Digital Signal Input
When digital signals are input, images are displayed correctly based on the preset data of the monitor, but if
you perform more advanced adjustment, see “2-4. Adjusting Color” (page 24) and subsequent pages.
●Analog Signal Input
Attention
• It takes about 7 minutes (under our measurement conditions) for the performance of electrical parts to stabilize. Please
wait 7 minutes or more after the monitor power has been turned on, and then adjust the monitor.
• The Self Adjust (automatic screen adjustment) function does not work for the images under the resolution of 800 × 600
(SVGA).
• The self adjustment and auto adjustment functions work correctly when an image is fully displayed over the Windows
or Macintosh display area. They do not work properly in the cases below:
- When an image is displayed only on a part of the screen (command prompt window, for example)
- When a black background (wallpaper, etc.) is in use
Also, these functions cannot work properly in some graphic boards.
The monitor screen adjustment is used to suppress ickering of the screen or adjust screen position and screen
size correctly according to the PC to be used.
Note
• The self adjustment function works when all of the following conditions are satised:
- When a signal is input into the monitor for the rst time or when a resolution or vertical/horizontal scan frequency not
used before is set
If the screen is not displayed correctly even after performing the self adjustment operation, adjust the screen
according to the procedures on the following pages to use the monitor comfortably.
How to Set
1. Prepare to use analog screen adjustment patterns.
Load the “EIZO LCD Utility Disk” to your PC, and then open the “Screen adjustment pattern les”.
Note
• For details and instructions on opening the “Screen adjustment pattern les”, refer to the Readme.txt le.

20 Chapter 2 Adjusting Screens
2.
Perform the auto adjustment with the analog screen adjustment pattern
displayed.
●Toadjustickering,screenposition,andscreensizeautomatically
Procedure
1. Display Pattern 1 in full screen on the monitor using the “Screen adjustment pattern les”.
2. Choose “Screen” from the Adjustment menu, and press .
3. Choose “Analog Adjustment” from “Screen”, and press .
4. Choose “Auto Adjustment” from “Analog Adjustment”, and press .
Flickering, screen position, and screen size are corrected by the auto-adjustment function.
If the screen is not displayed correctly even after performing Auto Adjustment, perform the adjustments
according to the procedures on the following pages. If the screen is displayed correctly, go to “2-4.
Adjusting Color” (page 24).
3.
Choose “Screen” from the Adjustment menu to perform advanced
adjustments.
Adjust the clock, phase and position, in this order.
●To eliminate vertical bars
Procedure
1. Choose “Analog Adjustment” from “Screen”, and press .
2. Choose “Clock” from “Analog Adjustment”, and press .
The “Clock” menu appears.
3. Adjust the clock with or to eliminate vertical bars.
Press or slowly so as not to miss the adjustment point.
4. Press to exit.
When blurring, ickering or bars appear on the screen after adjustment, proceed to “To remove ickering or blurring”.