Eizo DuraVision FDF2305W User manual

Important
Please read PRECAUTIONS, this User’s Manual, and the Setup Guide
(separate volume) carefully to familiarize yourself with safe and
effective usage.
• Please refer to the Setup Guide for basic information ranging from
connection of the monitor to a PC to using the monitor.
• The latest User’s Manual is available for download from our web site:
http://www.eizo.com
Color LCD Monitor
User’s Manual

2
Location of Caution Statement
<For USA-California Only>
CR Coin Lithium Battery contains Perchlorate Material - special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate.
This product has been adjusted specically for use in the region to which it was originally shipped. If
operated outside this region, the product may not perform as stated in the specications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information condential unless
prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every
effort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specications are subject to change without notice.

3
Notice for this monitor
Notice for this monitor
This product is suited for displaying surveillance camera images.
This product has been adjusted specically for use in the region to which it was originally shipped. If the
product is used outside the region, it may not operate as specied in the specications.
This product may not be covered by warranty for uses other than those described in this manual.
The specications noted in this manual are only applicable when the following are used:
· Power cords provided with the product
· Signal cables specied by us
Only use optional products manufactured or specied by us with this product.
It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more
after the monitor power has been turned on, and then adjust the monitor.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and
maintain a stable display.
When the screen image is changed after displaying the same image for extended periods of time, an
afterimage may appear. Use the screen saver or power save function to avoid displaying the same image for
extended periods of time.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer
to “Cleaning” (page 4)).
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may
appear on the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994% or higher.
The backlight of the LCD panel has a xed lifetime. When the screen becomes dark or begins to icker,
please contact your EIZO representative.
Do not press on the panel or edge of the frame strongly, as this may result in display malfunctions, such
as interference patterns, etc. If pressure is continually applied to the panel, it may deteriorate or damage
your panel. (If the pressure marks remain on the panel, leave the monitor with a black or white screen. The
symptom may disappear.)
Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do
not attempt to brush with tissues as this may scratch the panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew
condensation may occur on the interior and exterior surfaces of the monitor. In that case, do not turn the
monitor on. Instead wait until the dew condensation disappears, otherwise it may cause some damage to the
monitor.

4Notice for this monitor
Cleaning
Attention
• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet
or panel, and also quality deterioration of the image.
• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel.
Note
• The optional ScreenCleaner is recommended for cleaning the cabinet and panel surface.
The stains on the cabinet and panel surface can be removed by moistening part of a soft cloth with water.
To use the monitor comfortably
• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor
according to the environmental conditions.
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.

5
CONTENTS
CONTENTS
Notice for this monitor ......................................... 3
Cleaning .................................................................... 4
To use the monitor comfortably ............................. 4
CONTENTS............................................................. 5
Chapter 1 Introduction....................................... 7
1-1. Features ......................................................... 7
1-2. Controls and Functions ............................... 8
●Before Using Remote Control ......................... 9
1-3. EIZO LCD Utility Disk...................................10
●Disk contents and software overview ............10
1-4. Basic Operations and Functions ...............11
●Basic operation of the Setting menu..............11
●Functions........................................................12
Chapter 2 Adjusting Screens .......................... 13
2-1. Compatible Resolutions/Formats..............13
●Analog Input (D-Sub) .....................................13
●Digital Input (DVI-D, HDMI: PC signal) ..........13
●Digital Input (HDMI: video signal) ..................13
2-2. Setting the Resolution ................................14
2-3. Adjusting Color ............................................15
●To select the display mode (Color Mode).......15
●To perform advanced adjustments ................16
●Adjustable settings in each mode ..................16
●To adjust brightness .......................................17
●Adjusting the brightness and color of
black “Black Level”.........................................17
●To adjust contrast ...........................................17
●To adjust the color saturation.........................18
●To adjust hue..................................................18
●To adjust color temperature ...........................19
●To adjust gamma............................................19
●To adjust gain ................................................ 20
●To set the enhancement ratio of
ContrastEnhancer ......................................... 20
●Enabling Overdrive.........................................21
2-4. Screen Adjustment ..................................... 22
●Digital Signal Input ........................................ 22
●Analog Signal Input....................................... 22
2-5. Screen Size Changing................................ 26
●Analog Input (D-Sub)/Digital Input
(DVI-D, HDMI: PC signal) ............................. 26
●Digital Input (HDMI: video signal) ................. 27
Chapter 3 Setting Monitor ............................... 28
3-1. Adjusting Volume........................................ 28
●To turn the volume up/down.......................... 28
●To mute the sound temporarily...................... 28
3-2. Switching sound source for HDMI signal
input ............................................................. 29
3-3. To adjust the sound level ........................... 29
3-4. Enabling/Disabling DDC/CI
communication ........................................... 29
3-5. Locking Operation Buttons ....................... 30
3-6. Showing and hiding the EIZO logo ........... 30
3-7. Setting Language........................................ 30
3-8. Changing the authentication method for
HDMI signal input.........................................31
3-9. Resetting the Monitor to the Default
Settings.........................................................31
●To reset the color adjustments.......................31
●To reset all adjustments to the default
settings.......................................................... 32
Chapter 4 Using Smart Function .................... 33
4-1. Using Smart Function “Smart Detection”
“Smart Resolution” “Smart Insight” ........ 33
Chapter 5 Power Saving Functions ................ 36
5-1. Setting Power Saving ................................. 36
●Monitor .......................................................... 36
●To change the exiting method from the
power saving mode ........................................37
●Audio Output ..................................................37
5-2. Setting Power Indicator.............................. 38
5-3.
Enabling/Disabling Automatic Brightness
Adjustment “Auto EcoView”
........................... 38
5-4. Reducing Glare “EcoView Optimizer”...... 38
5-5. Checking the power saving level .............. 39
5-6. Enabling/Disabling Auto Power-OFF “Off
Timer”........................................................... 39
Chapter 6 Connecting Cables ......................... 40
6-1. Connecting Multiple External Devices..... 40
●To switch among input signals ...................... 40
6-2. Connecting External Speaker ....................41
Chapter 7 Troubleshooting.............................. 42
7-1. No picture .................................................... 42
7-2. Imaging problems
(for both digital and analog)...................... 43
7-3. Imaging problems (for digital only) .......... 43
7-4. Imaging problems (for analog only) ......... 44
7-5. Other problems ........................................... 45
Chapter 8 Reference ........................................ 46
8-1. How to Attach the Optional Arm ............... 46
8-2. Detaching/Attaching Stand Base...............47
8-3. Attaching/Detaching Cable Holder........... 49

6CONTENTS
8-4. Displaying Monitor Information ................ 50
8-5. Specications ..............................................51
8-6. Preset Timing .............................................. 54
Chapter 9 Glossary .......................................... 55
Appendix.............................................................. 58
Trademark ............................................................... 58
License / Copyright................................................ 58
FCC Declaration of Conformity ............................ 59
LIMITED WARRANTY............................................. 60
Recycling Information ........................................... 69
China Measures for RoHS Compliance in
ChinaRoHS.............................................................. 73

7
Chapter 1 Introduction
Chapter 1 Introduction
Thank you very much for choosing an EIZO color LCD monitor.
1-1. Features
• 23″ wide format LCD
• Supports a resolution of 1920 × 1080
• HDMI connector × 2
• A Color Mode function that provides optimal display modes for video captured by surveillance
cameras
See “To select the display mode (Color Mode)” (page 15).
• EIZO’s unique “Smart” technology
- Smart Insight function
This function analyzes the image and corrects the brightness for each pixel to make dark area of
images visible.
- Smart Resolution function
This function adjusts the perceived resolution of the images so that the blurs are reduced and images are
displayed vividly and clearly.
- Smart Detection function
This function allows the user to change the area on the screen to which the Smart Resolution or Smart
Insight function is applied (only animated images or whole screen).
See “Chapter 4 Using Smart Function” (page 33).
• Remote control enables easy operation, setting and adjustment of the monitor.
See “1-2. Controls and Functions” (page 8).
• Standard VESA mounting holes
Wall mounting is also supported.
• Displays HDCP (High-bandwidth Digital Content Protection) protected contents.
• A 2-year long-term warranty for 24-hour continuous use.

8Chapter 1 Introduction
1-2. Controls and Functions
Monitor
Setting menu*1 13 14
15
1 2 3 4 5 6 117 8 9 12
16
10
1. Auto EcoView sensor Detects ambient brightness (Auto EcoView function (page 38), EcoView Optimizer
function (page 38)).
2. Remote control
detector Receives the signal from the remote control.
3. button Switches input signals for display (page 40).
PC1 (DVI) → PC2 (D-SUB) → HDMI1 → HDMI2
4. / button Displays the volume adjustment menu to volume up or down.
5. button Turns the power on or off.
6. Power indicator
Indicates the monitor’s operation status.
Blue: Operating
Orange: Power saving mode
Red Power off
OFF: Main power off
7. Main power switch Turns the main power on or off.
8. Power connector Connects the power cord.
9. Input signal connector
(Left: HDMI connector × 2 (HDMI1, HDMI2) / Center: DVI-D connector /
Right: D-Sub mini 15-pin connector)
Connects external devices such as a PC.
10. Line input connector (Stereo mini jack)
Connects external devices such as a PC.
11. Line output connector (Stereo mini jack)
Connects a speaker with built-in amplier (page 41).
12. Headphone jack Connects the headphones.
13. Speaker Outputs audio source.
14. Security lock slot Complies with Kensington’s MicroSaver security system.
15. Stand*2 Adjusts the height and angle (tilt and swivel) of the monitor.
16. Handle
Handle used for transportation
Attention
• Firmly grasp and hold the monitor by the bottom while grabbing the handle, and
carefully convey the monitor so as not to drop it.
*1 See “Basic operation of the Setting menu” (page 11) for how to use.
*2 An optional arm (or an optional stand) can be attached by removing the stand (see “8-1. How to Attach the
Optional Arm” (page 46)).

9
Chapter 1 Introduction
Remote Control
1. PC/HDMI
Switches input signals for display.
• PC: PC1 (DVI) ←→ PC2 (D-SUB)
• HDMI: HDMI1 ←→ HDMI2
2. MODE Changes the color mode.
3. MENU Displays/Exits the Setting menu.
4. EcoView Displays/Exits “EcoView Menu”.
5. SIZE Changes the screen size.
6. Smart Displays/Exits the “Smart Functions” menu.
7. POWER Turns the power on or off.
8. OFF TIMER Sets the time until the monitor power-off.
9. / / /
• Provides the menu selection as well as the
adjustment and setting of a function.
• / : Displays the brightness adjustment menu
(page 17).
10. ENTER Determines an item on the menu screen, and saves
values adjusted.
11. RETURN Returns to the previous menu in menu operation.
12. VOLUME +/- Adjusts the volume.
13. MUTE Mutes sound temporarily.
●Before Using Remote Control
How to install battery
1. On the back of the remote control, slide the battery
cover off in the direction of an arrow.
2. Insert a battery with the positive side up. (Battery model
number: CR2025)
3. Reattach the cover.
Receivable Range of Remote Control
Use the remote control inside of the range as below.
5m
5m
20°
20°
7m
5m
30°
30°
7m
5m
12
7
8
11
13
1
2
4
6
5
9
10
3

10 Chapter 1 Introduction
1-3. EIZO LCD Utility Disk
An “EIZO LCD Utility Disk” (CD-ROM) is supplied with this product. The following table shows the disk
contents and the overview of the software programs.
●Disk contents and software overview
The disk includes software programs for adjustment, and User’s Manual. Refer to Readme.txt le on
the disk for software startup procedures or le access procedures.
Item Overview Windows
Macintosh
Screen adjustment pattern les Used when adjusting the image of analog
signal input manually.
√ √
User’s Manual of this monitor (PDF le) √ √
A Readme.txt le √ √

11
Chapter 1 Introduction
1-4. Basic Operations and Functions
●Basic operation of the Setting menu
1. Displaying the Setting menu
1. Press on the remote control. The Setting menu appears.
2.
Adjusting/Setting
1. Choose a menu to adjust/set with , , and then press . The Sub menu appears.
2. Choose an item to adjust/set with , , and then press . The adjustment/setting menu
appears.
3. Adjust/set the selected item with , , , , and then press .
3.
Exiting
1. Press .
Note
• To go back to the previous menu, press .

12 Chapter 1 Introduction
●Functions
The following table shows the Setting menu and setting items of each menu.
Main menu Setting Reference
Color*1 Color Mode “2-3. Adjusting Color” (page 15)
(Regarding “Smart Functions”, see
“Chapter 4 Using Smart Function”
(page 33).)
Brightness
Black Level
Contrast
Saturation
Hue
Temperature
Advanced Settings Gamma
Gain
ContrastEnhancer
Smart Functions
Overdrive
Color Reset “3-9. Resetting the Monitor to the
Default Settings” (page 31)
Screen Auto Screen Adjust*2 “2-4. Screen Adjustment” (page 22)
Auto Range Adjust*2
Clock*2
Phase*2
Position*2
Color Space*3
Smoothing
Sound Source*3 “3-2. Switching sound source for
HDMI signal input” (page 29)
Sound Level “3-3. To adjust the sound level” (page
29)
Power Save “5-1. Setting Power Saving” (page
36)
PowerManager Power Save
Monitor Settings DDC/CI “3-4. Enabling/Disabling DDC/CI
communication” (page 29)
Key Lock “3-5. Locking Operation Buttons”
(page 30)
Logo “3-6. Showing and hiding the EIZO
logo” (page 30)
Power Indicator “5-2. Setting Power Indicator” (page
38)
Language “3-7. Setting Language” (page 30)
Reset “3-9. Resetting the Monitor to the
Default Settings” (page 31)
Information “8-4. Displaying Monitor Information”
(page 50)
*1 The adjustment/settings available on the “Color” menu depend on the selected Color mode. The above
table shows the sub menus when the Day or Night mode is selected.
*2 These functions can be adjusted with analog input.
*3 This function is available with HDMI signal input.

13
Chapter 2 Adjusting Screens
Chapter 2 Adjusting Screens
2-1. Compatible Resolutions/Formats
The monitor supports the following resolutions and signal format.
●Analog Input (D-Sub)
Resolution Vertical Scan Frequency
640 × 480 up to 75 Hz
720 × 400 70 Hz
800 × 600 up to 75 Hz
1024 × 768 up to 75 Hz
1280 × 720 60 Hz
1280 × 960 60 Hz
1280 × 1024 up to 75 Hz
1680 × 1050 60 Hz
1920 × 1080*1 60 Hz
●Digital Input (DVI-D, HDMI: PC signal)
Resolution Vertical Scan Frequency
640 × 480 60 Hz
720 × 400 70 Hz
800 × 600 60 Hz
1024 × 768 60 Hz
1280 × 720 60 Hz
1280 × 960 60 Hz
1280 × 1024 60 Hz
1680 × 1050 60 Hz
1920 × 1080*1 60 Hz
*1 Recommended resolution
●Digital Input (HDMI: video signal)
• Video signal
Formats Vertical Scan Frequency
50 Hz 60 Hz
VGA -√
480p -√
480i -√
576p √-
576i √-
720p √ √
1080p √ √
1080i √ √
• Audio signal
- 2ch linear PCM (32 kHz / 44.1 kHz / 48 kHz)

14 Chapter 2 Adjusting Screens
2-2. Setting the Resolution
When you connect the monitor to the PC and nd that the resolution is improper, or when you want to
change the resolution, follow the procedure below.
Windows 8.1 / Windows 8 / Windows 7
1. For Windows 8.1 / Windows 8, click the “Desktop” tile on the Start Screen to display the desktop.
2. Right-click the mouse anywhere on the desktop except for icons.
3. From the displayed menu, click “Screen resolution”.
4. On the “Screen Resolution” dialog box, select the monitor.
5. Click “Resolution” to select the desired resolution.
6. Click the [OK] button.
7. When a conrmation dialog box is displayed, click [Keep changes].
Windows Vista
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Personalize”.
3. On the “Personalization” window, click “Display Settings”.
4. On the “Display Settings” dialog box, select the “Monitor” tab and select desired resolution in the
“Resolution” eld.
5. Click the [OK] button.
6. When a conrmation dialog box is displayed, click [Yes].
Mac OS X
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” dialog box is displayed, click “Displays” for “Hardware”.
3. On the displayed dialog box, select the “Display” tab and select desired resolution in the
“Resolutions” eld.
4. Your selection will be reected immediately. When you are satised with the selected resolution,
close the window.

15
Chapter 2 Adjusting Screens
2-3. Adjusting Color
●To select the display mode (Color Mode)
This function allows easy selection of a desired mode according to monitor application.
Display Modes
Mode Purpose
Day Suitable for displaying common video captured by surveillance cameras.
Night Suitable for displaying monochrome video such as that captured at night by surveillance
cameras.
sRGB Suitable for color matching with sRGB compatible peripherals.
Displays the current mode.
Procedure
1. Press on the remote control.
The mode name appears at the center of the screen.
2. The mode among the list is highlighted in turn each time is pressed.
You can switch the current mode with or while the mode menu is being displayed.
→Day←→Night←→sRGB←
Note
• The Setting menu and the Mode menu cannot be displayed at the same time.

16 Chapter 2 Adjusting Screens
●To perform advanced adjustments
The “Color” menu of the Setting menu allows you to set and save the independent color adjustment
for each mode.
Attention
• It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more
after the monitor power has been turned on, and then adjust the monitor.
• Perform the range adjustment rst when adjusting color for analog signals (see “To adjust color gradation
automatically” (page 25)).
• The same image may be seen in different colors on multiple monitors due to their monitor-specic
characteristics. Make ne color adjustment visually when matching colors on multiple monitors.
●Adjustable settings in each mode
The adjustable settings depend on the mode. (Non-adjustable or non-settable function cannot be
selected.)
For instructions on how to adjust or set each function, refer to subsequent pages.
(Regarding “Smart Functions”, see “Chapter 4 Using Smart Function” (page 33).)
√: Adjustable -: Not adjustable
Function Color Mode
Day Night sRGB
Brightness √√√
Black Level √ √ -
Contrast √ √ -
Saturation √ √ -
Hue √ √ -
Temperature √ √ -
Advanced Settings Gamma √ √ -
Gain √ √ -
ContrastEnhancer √ √ -
Smart Functions
√ √ -
Smart Detection
Smart Resolution
Smart Insight
Overdrive √ √ -
Color Reset √√√

17
Chapter 2 Adjusting Screens
●To adjust brightness
The screen brightness is adjusted by changing the brightness of the backlight (light source from the
LCD back panel).
Adjustable range
0 to 100
Procedure
1. Press or .
The Brightness menu appears.
2. Use or for adjustment.
3. Press to exit.
Note
• If you feel that the image is too dark even if the brightness is set to 100, adjust the contrast.
• Alternatively, you can use “Brightness” under “Color” in the Adjustment menu to adjust it.
●Adjusting the brightness and color of black “Black Level”
You can adjust the brightness and chromaticity of black by adjusting the black level of red, green, and
blue respectively. Please use a black test pattern or background for adjustment of the black level.
Adjustable range
0 to 100
Procedure
1. Choose “Color” in the Setting menu, and press .
2. Choose “Black Level” in the “Color” menu, and press .
The “Black Level” menu appears.
3. Use or for adjustment.
4. Press to exit the adjustment.
Note
• After completing black level adjustment, readjust the contrast as appropriate.
●To adjust contrast
The brightness of the screen is adjusted by varying the video signal level.
Adjustable range
0 to 100
Procedure
1. Choose “Color” in the Setting menu, and press .
2. Choose “Contrast” in the “Color” menu, and press .
The “Contrast” menu appears.
3. Use or for adjustment.
4. Press to exit the adjustment.
Note
• In the contrast of 50, every color gradation is displayed (for PC input signal only).
• When adjusting the monitor, it is recommended to perform the brightness adjustment which may not lose the
gradation characteristics, prior to the contrast adjustment.
• Perform the contrast adjustment in the following cases.
- When you feel the image is too dark even if the brightness is set to 100 (Set the contrast to higher than 50.)

18 Chapter 2 Adjusting Screens
●To adjust the color saturation
This function allows you to adjust color saturation.
Adjustable range
-50 to 50
Procedure
1. Choose “Color” in the Setting menu, and press .
2. Choose “Saturation” in the “Color” menu, and press .
The “Saturation” menu appears.
3. Use or for adjustment.
4. Press to exit the adjustment.
Attention
• Using this function may make some color gradations unavailable for display.
Note
• The minimum value (-50) changes the screen to monochrome.
●To adjust hue
This function allows you to adjust hue.
Adjustable range
-50 to 50
Procedure
1. Choose “Color” in the Setting menu, and press .
2. Choose “Hue” in the “Color” menu, and press .
The “Hue” menu appears.
3. Use or for adjustment.
4. Press to exit the adjustment.
Attention
• Using this function may make some color gradations unavailable for display.

19
Chapter 2 Adjusting Screens
●To adjust color temperature
Color temperature can be adjusted.
The color temperature is normally used to express the hue of “White” and/or “Black” by a numerical
value. The value is expressed in degrees “K” (Kelvin).
The screen becomes reddish at a low color temperature, and bluish at a high color temperature, like
the ame temperature. A gain preset value is set for each color temperature setting value.
Adjustable range
Off, 4000K-10000K (specied by every 500K unit, including 9300K)
Procedure
1. Choose “Color” in the Setting menu, and press .
2. Choose “Temperature” in the “Color” menu, and press .
The “Temperature” menu appears.
3. Use or for adjustment.
4. Press to exit the adjustment.
Note
• The value shown in “K” is available only as reference.
• “Gain” allows you to perform more advanced adjustment (see “To adjust gain” (page 20)).
• If you set to “Off”, the image is displayed in the preset color of the monitor (Gain: 100 for each RGB).
• When gain is changed, the color temperature is changed to “Off”.
●To adjust gamma
Gamma can be adjusted. The brightness of the monitor varies depending on the input signal,
however, the variation rate is not proportional to the input signal. To keep the balance between the
input signal and the brightness of the monitor is called as “Gamma correction”.
Adjustable range
1.8, 2.0, 2.2, 2.4, 2.6, 2.8, Power
Procedure
1. Choose “Color” in the Setting menu, and press .
2. Choose “Advanced Settings” in the “Color” menu, and press .
3. Choose “Gamma” in the “Advanced Settings” menu, and press .
The “Gamma” menu appears.
4. Use or for adjustment.
5. Press to exit the adjustment.
Note
• Choosing “Power” will help to sharpen halftone images by increasing their contrast.

20 Chapter 2 Adjusting Screens
●To adjust gain
The brightness of each color component red, green, and blue is called “Gain”. You can change the
hue of “white” by adjusting gain.
Adjustable range
0 to 100
Procedure
1. Choose “Color” in the Setting menu, and press .
2. Choose “Advanced Settings” in the “Color” menu, and press .
3. Choose “Gain” in the “Advanced Settings” menu, and press .
The “Gain” menu appears.
4. Adjust gain with or for each of red, green, and blue.
5. Press to exit the adjustment.
Attention
• Using this function may make some color gradations unavailable for display.
Note
• The value of gain changes with that of color temperature.
• When gain is changed, the color temperature is changed to “Off”.
●To set the enhancement ratio of ContrastEnhancer
This function allows you to automatically adjust the contrast according to the darkness or brightness
of an image and change in scenes. You can set the level of the adjustment.
Adjustable range
Enhanced, Standard, Off
Procedure
1. Choose “Color” in the Setting menu, and press .
2. Choose “Advanced Settings” in the “Color” menu, and press .
3. Choose “ContrastEnhancer” in the “Advanced Settings” menu, and press .
The “ContrastEnhancer” menu appears.
4. Use or for adjustment.
5. Press to exit the adjustment.
Attention
• Using this function may make some color gradations unavailable for display.