Elan EL-4KM-V44-18G User manual

EL-4KM-V44-18G QUICK REFERENCE GUIDE
© 2022 ELAN®is a registered trademark of Nortek Security & Control LLC. All rights reserved. RevA3_QRG_ELAN_EL-4KM-V44-18G_PrintReady
Panel Description
RS-232 Configuration
The RS-232 port is used for configuration and control of the product, as well as pass through of RS-232 commands to a compatible ELAN HDBaseT receiver / matrix device.
The default RS-232 communication settings are:
Baud Rate: 57600
Data Bit: 8
Stop Bit: 1
Parity Bit: none
For a complete RS-232 command list please see the EL-4KM-V44-18G user manual - available to download from www.elancontrolsystems.com
The ELAN®4x4 HDBaseT matrix offers unprecedented performance and value for the custom installation market. The EL-4KM-V44-18G is a
HDMI 2.0 4K 60Hz 4:4:4 HDCP 2.2 matrix utilizing CSC technology to deliver HDMI, bi-directional IR and PoC up to lengths of 70m over a single
CAT cable. The matrix also provides advanced features including simultaneous HDBaseT / HDMI on output 1, video down conversion on HDBaseT
outputs and a web browser interface module for control and configuration of the matrix.
EL-4KM-V44-18G
Quick Reference Guide
Rear
1IR Receiver - Built in IR sensor for IR pass through
2Output LCD - Shows the currently selected output
3Output Up / Down Button - Press to adjust the selected output up or down
4Input Up / Down Button - Press to adjust the selected input up or down / Press and hold Input Up to power the matrix on or off
5Input LCD - Shows the currently selected input
Please note: Press and hold Output Up and Input Down for 10 seconds to factory reset the matrix.
EL-4KM-V44-18G
OUTPUTS
OUTPUTS
INPUTS
INPUTS
®
1
Front
2 3 4 5
IR CTRL TCP/IP
INPUTS
IR OUTPUTS
OUTPUTS
IR INPUTS 100-240VAC IN
1234 1234
HDMI 1 HDMI 2 HDMI 3 HDMI 4HDMI 1 HDBT 1 HDBT 2MIRRORED
RS-232
HDBT 3 HDBT 4
1 3 42 5
6 7 8 9
1IR Control Input - 3.5mm stereo connector to connect to
ELAN 5V 3.5mm IR receiver for IR control of the matrix
2TCP/IP - RJ45 connector for TCP/IP and Web GUI control
of the matrix
3RS-232 - DB9 connector for RS-232 control of the matrix
4IR Receiver Output - 3.5mm mono connector to connect to
ELAN 5V 3.5mm IR emitter. Used for local Source control
5IR Receiver Input - 3.5mm stereo connector to connect to
ELAN 5V 3.5mm IR receiver or Control Processor. Used to
extend IR from Matrix to HDBaseT Outputs 1-4
6HDMI Inputs - Connect to source devices
7HDMI Output - Connect to display device
8HDBaseT Outputs - RJ45 HDBaseT port to connect to
the HDBaseT input port of the compatible ELAN HDBaseT
receiver
9IEC Power Socket - Use supplied IEC power cable
RevA3_QRG_ELAN_EL-4KM-V44-18G_Working.indd 1RevA3_QRG_ELAN_EL-4KM-V44-18G_Working.indd 1 25/02/2022 11:0925/02/2022 11:09

EL-4KM-V44-18G QUICK REFERENCE GUIDE
© 2022 ELAN®is a registered trademark of Nortek Security & Control LLC. All rights reserved. RevA3_QRG_ELAN_EL-4KM-V44-18G_PrintReady
Package Contents:Specifications:
• 1 x EL-4KM-V44-18G
• 1 x Rack mounting kit
• 1 x Remote control
• 4 x IR emitters
• 5 x IR receivers
• 1 x RS-232 control cable
• 1 x IR control cable - 3.5mm-3.5mm cable
• 1 x Quick Reference Guide
• 4 x IEC Power cables (US, UK, EU & AU)
FCC Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION - changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
CANADA, INDUSTRY CANADA (IC) NOTICES
This Class B digital apparatus complies with Canadian ICES-003.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
CORRECT DISPOSAL OF THIS PRODUCT
This marking indicates that this product should not be disposed with other household wastes. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material
resources. To return your used device, please use the return and collection systems or contact the retailer where the product was
purchased. They can take this product for environmentally safe recycling.
Certifications
Tech Support:
[email protected]
Main:
1 [phone] - US
1 [phone] - International
1 [phone] - Fax
Web:
elancontrolsystems.com
Video Input Connectors: 4 x HDMI Type A, 19-pin, female
Video Output Connectors: 1 x HDMI Type A, 19-pin, female, 4 x
HDBaseT™ RJ45 connectors
RS-232 Serial Port: 1 x 3-pin Phoenix conenctor
IR Input Ports: 5 x 3.5mm stereo jack
IR Output Ports: 4 x 3.5mm mono jack
Rack Mountable: 1U rack height, rack ears included
Casing Dimensions (W x H x D): 437mm x 44mm x 377mm (without feet)
Dimensions (W x H x D): 437mm x 53mm x 384mm
Shipping Weight: 6.25kg
Operating Temperature: 32°F to 104°F (-5°C to +55°C)
Storage Temperature: -4°F to 140°F (-25°C to +70°C)
Power Supply: Internal 100-240V AC 3A
HDBT Power Output: 12V DC 0.8A Per Port
RevA3_QRG_ELAN_EL-4KM-V44-18G_Working.indd 2RevA3_QRG_ELAN_EL-4KM-V44-18G_Working.indd 2 25/02/2022 11:0925/02/2022 11:09

EL-4KM-V44-18G QUICK REFERENCE GUIDE
© 2022 ELAN®is a registered trademark of Nortek Security & Control LLC. All rights reserved. RevA3_QRG_ELAN_EL-4KM-V44-18G_PrintReady
Information
A. Read these instructions – All the safety and operating instructions should be read before this product is operated.
B. The apparatus should be connected to a mains socket outlet with a protective earthing connection.
C. The socket-outlet shall be installed near the equipment and shall be easily accessible.
D. Do not ingest battery, Chemical Burn Hazard
E. This product contains a coin / button cell battery. If the coin / button cell battery is swallowed, it can cause severe internal burns in
just 2 hours and can lead to death.
F. Keep new and used batteries away from children.
G. If the battery compartment does not close securely, stop using the product and keep it away from children.
H. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
I. WARNING: Please refer the information on exterior bottom enclosure for electrical and safety information before installing or
operating the apparatus.
A. Lisez ces instructions - Toutes les instructions de sécurité et d’utilisation doivent être lues avant d’utiliser ce produit.
B. L’appareil doit être raccordé à une prise de courant avec une mise à la terre de protection.
C. La prise de courant doit être installée à proximité de l’appareil et doit être facilement accessible.
D. Ne pas ingérer la batterie, risque de brûlure chimique
E. Ce produit contient une pile bouton. Si la pile bouton est avalée, elle peut provoquer de graves brûlures internes en seulement 2
heures et peut entraîner la mort.
F. Conservez les piles neuves et usagées hors de portée des enfants.
G. Si le compartiment à piles ne ferme pas correctement, cessez d’utiliser le produit et tenez-le hors de portée des enfants.
H. Si vous pensez que des piles ont pu être avalées ou placées à l’intérieur d’une partie du corps, consultez immédiatement un
médecin.
I. AVERTISSEMENT : Avant d’installer ou d’utiliser l’appareil, veuillez vous référer aux informations figurant sur le boîtier inférieur
extérieur pour les informations relatives à l’électricité et à la sécurité.
RevA3_QRG_ELAN_EL-4KM-V44-18G_Working.indd 3RevA3_QRG_ELAN_EL-4KM-V44-18G_Working.indd 3 25/02/2022 11:0925/02/2022 11:09

EL-4KM-V44-18G QUICK REFERENCE GUIDE
© 2022 ELAN®is a registered trademark of Nortek Security & Control LLC. All rights reserved. RevA3_QRG_ELAN_EL-4KM-V44-18G_PrintReady
RS-232
HDMI
IR
CAT
Network Connection
Maximum of 4 x 4K 60Hz 4:4:4 Sources
Example Schematic
EL-4KM-V44-18G
12V PoC
HDMI
IR
RS-232
SOURCE 01 SOURCE 02 SOURCE 03 SOURCE 04
1 2 3 4
L/R OUTOPT OUTHDMI OUTIR OUTIR INRS-232
HDBT
IN
12V 1A
TX RX
L/R OUTOPT OUTHDMI OUTIR OUTIR INRS-232
HDBT
IN
12V 1A
TX RX
AVR
4K Projector
4K Display
IR Emitter
Link to Source
70m Max @ 1080p and 40 @ 4K 70m Max @ 1080p and 40 @ 4K
Control Processor
Max 4 x 4K
Displays via
HDBaseT™
EL-4KHDBT-RX-40-18G EL-4KHDBT-RX-40-18G
IR CTRL TCP/IP
INPUTS
IR OUTPUTS
OUTPUTS
IR INPUTS 100-240VAC IN
1234 1234
HDMI 1 HDMI 2 HDMI 3 HDMI 4HDMI 1 HDBT 1 HDBT 2MIRRORED
RS-232
HDBT 3 HDBT 4
RevA3_QRG_ELAN_EL-4KM-V44-18G_Working.indd 4RevA3_QRG_ELAN_EL-4KM-V44-18G_Working.indd 4 25/02/2022 11:0925/02/2022 11:09