ELBRO ST-SK1 User manual

I N S T A L L A T I O N
M A N U A L
GSM
Alarm Security System™ ST-SK1

3
Features
- GSM transmiter
- Supports up to 10 remote controls, 99 wireless accessories and 50 RFID tags
- Can store up to 5 phone numbers, 5 SMS numbers.
a Central Monitoring System)
- Arm / disarm the system by SMS, phone call, or App (on iOS or Android)
- Can be disarmed by RFID tag
- Built-in siren (110dB)
- Call function from the panel
- SMS alerts for power failure, power recovery and low battery
- Audio surveillance of the site from distance
- 2 x 800mAh lithium batteries included (8h battery life in standby mode)
Speci ications
Product name
ST-SK1
SKU
ST-SK1
Control panel power supply
Input: AC 110-240V / 50-60 Hz
Output: DC 12V / 800 A
GSM working frequency
850 / 900 / 1800 / 1900 mHz
Radio-frequency
433.92MHz (±75KHz)
Transmission distance
80m in open space
Standby current
80ma
Alarm current
300mA
Backup batteries
Lithium Baeries: 3.7V / 800 mAh x 2 (BL-5B)
(8h baery life in standby mode)
Internal siren
95dB
Housing material
ABS plasc
Operating conditions
Temperature: -10°C~55°C
Humidity: ≤ 80% (non-condensing)
Control panel dimensions (L x W x H)
188 x 125 x 25 mm
Boxcontent
SS1 Control Panel x1
Moton Detectors x1
Door / Window Contacts x1
Remote Controls x2
RFID Tags x2
AC Adaptor x1
Documentaon x1
Boxcontent
Call
Clear
RFID Reader
Home Mode
LCD Display
Disarm
Record
Arm
SOS
ControlPanelLayout(Back)
Power On/O
Adapter interface
24h Zone
Electronic lock
Wired siren
GND
SPK
LOCK
Z1
+12V
GND
Monitoring MIC
Speaker
Power Supply Interface
Tamper Switch
Power Switch
Telephone Interface
Battery
Compartment
SIM Card Slot

54
QuickStart-upGuide
ConnectyourSystem
UsingtheGSMtransmier(SIMcard)
Open the baery compartment at the back of the control panel and insert a SIM card in the
control panel.
Important
Before using the SS1 in GSM mode, you need to purchase a SIM card that works on the GSM
network with 850 / 900 / 1800 / 1900 MHz frequency. We recommend you to subscribe to a
plan with unlimited texts and one hour of voice. For more informaon, please contact your local
reseller.
Important
Make sure the SIM card does not require any PIN code. For more informaon, please contact
your local reseller.
TurningyourSystemon
1.
Plug the AC adaptor to an AC socket.
2.
Plug the output connector of the AC adaptor into the
adaptor interface in the baery compartment at the back
of the control panel.
3. Turn the power switch to "ON" (in the
battery compartment at the back of the control panel).
MounttheControlPanel
                

Fix the wall-mounng bracket on the wall with screws. Wedge the panel on the bracket, make sure
they t well.
BasicOperations
ArmtheSystem
Press the Arm button " " on the control panel. The control panel beeps once: the system is
armed. The LCD display indicates "Armed" and the Arm icon on the control panel is lit.
Note
If the Entry / Exit Delay is acvated, all zones except the 24h zone will be armed aer the delay set
(refer to the instrucons on page 10 of this manual “Entry / Exit Delay”).
DisarmtheSystem
Type your user code and press the Disarm button " " on the control panel. The control
panel beeps twice: the system is disarmed.
HomeMode
Press the Home buon " " on the control panel. The control panel beeps once: the system is armed
in Home Mode.
All the sensors assigned to the Normal zone are armed. The sensors assigned to the Home zone
are disarmed.
EmergencyMode
Hold the “#SOS” button for 3 seconds. The alarm is triggered immediately and the siren rings out.
At the same time, the control panel dials the stored phone numbers.

6
SpeedDial
Press the Call button “ ” on the control panel for 3 seconds: the panel auto-dials the first
stored phone number. Press the Call button “ ” to end the call.
Hands-freePhoneCallfromthePanel
ThroughGSM
Press the Call button“ ” on the control panel,type the phone number you wish to call and press
the Call button “ ”again.
Record/PlayaVoiceMemo
Long press the Record Voice Memo buon to record a 10-second voice message. The Play Voice Memo Buon
blinks when a message has been recorded. Push the center of the RFID reader in the control panel to listen to the
voice memo. The LED indicator turns o when the voice memo is being played. Touch it again to replay the memo.
HardReset
Turn the control panel on. Press the tamper switch at the back of the control panel 5 mes
wirthin 5 seconds aer having turned it on.
Sengs will be restored to default values. Stored phone numbers and connected accessories
will be cleared.
7
Setupfromthecontrolpanel
The SS1 must be set up before using for the rst me. During the setup of the system, the control
panel can be powered either by the AC power adapter or by the backup baeries.
Defaultcodes
- Admin code (necessary to set up your system): 123456
- User code (necessary to disarm your system or stop the alarm): 1234
- Duress code: 0000 (enables you to trigger a duress alarm)
- Open door code: 8888 (enables you to open an electronic door lock plugged to your
control panel and disarm your system or stop the alarm)
  

The control panel of your alarm system features an LCD display that enables you to navigate
through the menu of the control panel and set up your alarm system.
To enter the setng menu, In disarm status, then ( + Enter)on the control panel.
In the table on the next page, each column represents a menu or a sub menu. Each menu or
submenu will be displayed on one of the two lines of the LCD display. On the LCD display, the
current menu, submenu, or seng is shown on the line at the boom, while the previous menu
or submenu is shown on the line at the top.
Navigate and select the setting you wish to modify with the keys “ ”or “ ”, and enter
each menu or sub menu by pressing “Enter”.
How to use the keyboard
“*“ = delete
“ ” = move forward
“ ” = move backward
“Enter” = select / confirm
“Esc” = back / previous step in the menu / cancel
The tables on the next pages summarize all the sengs that can be accessed and modied on
the control panel.

98
Main Menu Sub Menu 1 Sub Menu 2 Sub Menu 3 Comments
Phone numbers
Phone[1~5] is:
-
Select the phone or SMS number you want to edit, type in the phone number and confirm with the key "Enter".
Use the key *" " to clear.
5 phone numbers and 5 SMS numbers can be stored in the control panel.
SMSNum[1~5]Is:
Accessories Remote&Keypad
Add a new 01/10 30
The LCD screen displays “01/10” (at the left), which indicates the number of the remote control you are about to
connect (01 is the current remote control, 10 is the total number of remote controls you can connect), and
"30" (at the right), which indicates the time remaining to connect the remote control. Press any key on the
keypad or remote control, you hear one beep: the connection is successful.
Once the remote control has been added, the countdown starts over from 30 so that you can register another
remote control in control panel (up to 10 remote control can be registered in the control panel). Press Esc to exit.
Delete All 1=YES 0=NO
Delete a Remote Input 01-10: Enter the number of the Remote Control you wish to delete and press "Enter".
Accessories RFIDTag
Add a new 01/50 30
The LCD screen displays “01/50” (at the left), which indicates the number of the RFID tag you are about to
connect (01 is the current RFID tag, 50 is the total number of tags you can connect), and "30" (at the right), which
indicates the time remaining to connect the RFID tag. Swipe the RFID tag in front of the RFID reader, you hear
one beep: the connection is successful.
Once the RFID tag has been added, the countdown starts over from 30 so that you can register another RFID tag in
control panel (up to 50 tags can be registered in the control panel). Press Esc to exit.
Delete all 1=YES 0=NO
Delete a Tag Input 01-50: Enter the number of the RFID tag you wish to delete and press "Enter".
Accessories Wireless
Sensors
Add a new
Home Zone
Delay Zone
Normal Zine
24-H Zone
Select the sensor type you wish your sensor to be assigned to (Normal Sensor, 24 Hour Sensor, Delay Sensor,
or Home Sensor), press “Enter” to confirm. For more information on zone setup, please refer to page 14 of
this manual.
The LCD screen displays “01/99” (at the left), which indicates the number of the sensor you are about to connect
(01 is the current sensor, 99 is the total number of sensors you can connect), and "30" (at the right), which
indicates the time remaining to connect the sensor. Trigger the sensor, you hear one beep: the connection is
successful.
Once the sensor has been added, the countdown starts over from 30 so that you can register another sensor in
control panel (up to 99 sensors can be registered in the control panel). In such case, the sensor will be added to
the same zone. Press Esc to exit.
Delete all? 1=YES 0=NO
Delete a Sensor Input 01-99: Enter the number of the sensor you wish to delete and press "Enter".
Accessories TestMode -
Trigger the sensors you have previously connected to the control panel. You hear 1 beep, the LCD screen displays
the signals that have been respectively sent by each sensor triggered. Make sure all the sensors you have
triggered are mentioned on the LCD screen. Press “Esc” to exit the test mode.
This mode enables you to test if the sensors have been connected successfully to the control panel.

1110
Main Menu Sub Menu 1 Sub Menu 2 Sub Menu 3 Comments Note
System Seng DateandTime YYYY-MM-DD TIME 
System Seng DateFormat
System Seng EntryExitDelay
Entry Delay 000-300 This funcon can be used if you do not want to bring a remote con-
trol or RFID tag with you. When the system is armed, you hear one
beep every second to remind you to leave. The beep rhythm speeds
up during the last 10 seconds. If an intruder is detected, the alarm
will be delayed accordingly.
Time is calculated in seconds. The Entry and Exit Delay can be set
from 0 to 300 seconds.
The entry and exit delays only work
for sensors connected as Delay Zone
accessories (see "Wireless" on page 8).
The EntryDelay gives you me to disarm
the system on the control panel without
triggering an alarm.
The ExitDelay gives you me to arm the
system on the control panel and leave your
home without triggering an alarm.
Exit Delay 000-300
System Seng AutoArm/Disarm
Auto Arm Time <00:00>
You can set up the system to arm and disarm automacally at a
dened me every day.
Seng Auto Arm and Auto Disarm to
the exact same me will deacvate the
funcon.
Auto Disarm Time <00:00>
ON or OFF?
System Seng ControlbyPhone ON or OFF? -
You can acvate or deacvate the control of your system by phone
call. Acvang the control by phone call enables you to arm and
disarm the system and monitor your home by phone call.
See instrucons on page 14 for more
informaon on the control of the system
by phone call.
System Seng GSMFailAlarm ON or OFF? Nocaon of SIM/ GSM signal problem. Deacvate this funcon if you want to
use the alarm system in PSTN mode only.
System Seng Keypadtones ON or OFF? - Acvate or deacvate the sound when typing on the keyboard of the
control panel.
System Seng Accesscode
Admin Code 123456 Your admin code enables you to enter the setup menu.

It is recommended to change all codes
before using your system for the rst
me and to keep your codes secret
User Code 1234
Your user code enables you to disarm the system on the control
panel. The user code is the access code requested when you call the
control panel.

Duress Code 1111
In case of emergency, when you are requested to disarm the system
by force, it is recommended to disarm your system with your Duress
Code. The panel will silently dial the stored phone numbers.

Open Door Code 8888 You can open electronic doors using this code. The door must be
wired to the [LOCK] interface on the back of the control panel.

1312
Main Menu Sub Menu 1 Sub Menu 2 Sub Menu 3 Comments Note
System Sengs RingTimes <1-9>: 5 -
Enter the value (from 1 to 9) and confirm with "Enter".
This funcon enables you to determine the number of mes the control
panel will ring before taking your call (for control by phone call).
System Sengs SirenAlertTime <1-9Min>: 3
Enter the value (from 1 to 9) and confirm with "Enter".
This funcon enables you to determine for how long the siren rings out
in case of alarm.
System Sengs BacklightTime <0-120s>: 30 - Enter the value (from 0 to 120) and confirm with "Enter".
Default seng is 30 seconds.
System Sengs SirenSetup
Wired Siren
Siren Switch
ON/OFF
Enable / Disable the siren.
Default seng: On Wired siren refers to a siren connected
to the control panel by wire.
Arm/Disarm Tone
ON/OFF
Arm / Disarm silently.
Default seng: On
Built-in Siren
Siren Switch
ON/OFF
Enable / Disable the siren.
Default seng: On Built-in siren refers to the siren featured
in the control panel.
Arm/Disarm Tone
ON/OFF
Arm / Disarm silently.
Default seng: On
Wireless Siren
Siren Switch
ON/OFF
Enable / Disable the siren.
Default seng: On Wireless siren refers to a siren connect-
ed to the control panel by radio-fre-
quency.
Arm/Disarm Tone
ON/OFF
Arm / Disarm silently.
Default seng: On
System Sengs
UserID On / O -When Disarm Upload is on, the system will upload the history of
arm/disarm events to the to the CMS.
DisarmUpload On / O -
System Sengs CallRecycle <1-9>: 3
When the alarm is triggered, the control panel dials the numbers
you have stored. If you do not disarm the system, the control panel
will call you again (up to 9 mes). The “Call Recycle” funcon en-
ables you to dene the number of mes the control panel aempts
to call you. Default seng: 3 mes.
System Sengs Language - - Select the language you wish to choose and confirm with "Enter". Languages available may vary depending
on the version of your product.
System Sengs Reset 1=YES 0=NO -All system sengs will be restored to default seng.
Stored phone numbers and connected accessories will be cleared.
System Sengs About About Jun 4 2014 -
History -- - Choose the event log you need to track, press “Enter”. The control panel keeps in record the
latest 150 event logs.

1514
Zonesetupofaccessories
Every detector can be assigned to 4 dierent categories of zones: Home Zone, Delay Zone, Normal
Zone and 24-H Zone. To assign a detector to a zone, follow the instrucons on page 8 of this
manual (the zone will be assigned at the me of connecon of the accessory).
Normalzone
When the system is armed, if a sensor is triggered, the siren rings out. When the system is disarmed,
sensors do not trigger an alarm.
24hzone
Regardless the system is armed or disarmed, sensors assigned to the 24h zone can trigger an alarm.


Delayzone
If you want to set up the entry and exit delay funcons, corresponding sensors must be assigned to
the Delay zone. Once the delay me has been set up, the sensors will not trigger the alarm during
the delay set. Refer to the instrucons “Entry and Exit Delay” on page 10 of this manual.  

Homezone
When the system is armed in Home Mode, the sensors assigned to the Home zone do not trigger an
alarm. 

Controlbyphonecall


Method 1
When an alarm has been triggered, the control panel dials the stored phone numbers. When you
pick up the phone, follow the voice instrucons to control t he p anel from distance (refer to the
instrucons in the table below).
Method 2
1. Dial the telephone number of your control panel (either the number of the SIM card in your
control panel or the number of the landline to which your panel is connected). Aer geng through,
the voice instrucons will guide you to enter your access code.
2. Enter your user code, followed by ”#”.
3. A voice gives you the opons you can select.
4. Select the operaons to control the panel (see instrucons in the table below).
Note
The call will end automacally if you do not send any command within 30 seconds.
Tableofcommandsforcontrolbyphonecall
Command Function Comment
Press “1“ Arms the system
Press “0“
-Disarms the system and turns the
siren o
-Stops monitoring without hanging up
- Stops the phone call funcon without
hanging up
Press “3“ Phone call with control panel
Press "*"
- Starts audio monitoring mode (not
limited in me)
- Stops the built-in siren and the wire-
less siren (if connected to the control
panel)
-
Press “6“ Turns all sirens o -
Press “9“
- Turns the built-in siren on (whether
the siren ringing sengs is ON or
OFF)
- Turns the wireless siren on (if con-
nected to the control panel)
-
Press “#“
- Turns all sirens o
- Exits control by phone call
- Stops call recycles
-
Note
In GSM mode, the audio monitoring is not limited in me.

1716
SetupbySMS
IMPORANT:BEFORE USINGFOR THEFIRST TIME
Insert a SIM card in the control panel before starng SMS operaons.
Make sure the SIM card does not require any PIN code.
SAVE A SMS NUMBER IN THE CONTROL PANEL (using the control panel).
Only stored numbers can control and congure the system.

Each SMS operaon dened in this user manual will be illustrated as follows:
You send:
SMS Command
The control panel replies:
Control panel’s reply
       

       
.
      

        

The system is in English by default. To change the system language, refer to the instrucons
on page 22 of this manual.
Important
When replying to the control panel by SMS, make sure no space follows punctuaon marks like "."
or ":". For examples, to store SMS numbers, your SMS must be formaed as follows:
SMS numbers:
1.067890033
2.067890022
3.067890011
4.067890000
5.
No space aer "1."
Disarmthe System
Send:
System disarmed.
ArmtheSystem
Send:
System armed.
HomeMode
Send:
System in home mode.
SettingsEnquiry
Send:
System:Disarmed
AC power:on
Note
The values indicated hereinabove will change
aer having set up the system.
0
1
2
00

1918
StorePhoneNumbers
Send:
5
Phone numbers:
1.
2.
3.
4.
5.
Copy, paste, then edit
(case sensive):
Phone numbers:
1. 067890033
2. 067890022
3. 067890011
4. 067890000
5.
Ok
StorePhoneNumbersforSMS Notifications
Send:
SMS numbers:
1.
2.
3.
4.
5.
Copy, paste, then edit
(case sensive):
Ok
Note
The rst SMS number will receive SMS
nocaons when the system is disarmed by
RFID tag. To start receiving these nocaons,
you must rename the RFID tags. Up to 4 RFID tags
can be renamed. Other tags will be aributed a
number based on the order of registraon to
the control panel. Refer to the instrucons on
page 8 to learn how to register an RFID tag
in the control panel.
RenameZones
Send "91~99". For example for zone 1,
send:
91
Zones names:
1.
Copy, paste, then edit
(case sensive):
Zones names:
1.Entrance door sensor
Ok
Note
Zones 1 to 9 can be renamed. The name of
the zone cannot consist of more than 30
Latn characters. Zones 10 to 99 cannot be
renamed.
SMSAlertforAccessoryLowBattery
(available for two-way acessories such as Motion
Detectors)
For accessories assigned to zones that have
been renamed, an SMS will be sent
under the format “Zone name + low
battery”.
Bedroom PIR low baery
For accessories assigned to zones that have
not been renamed, an SMS will be sent
under the format “Zone number + low
battery”.
Zone 10 low baery.
SMSAlertforAccessoryTamper
Alarm
(available for two-way acessories such as Motion
Detectors)
For accessories assigned to zones that have
been renamed, an SMS will be sent
under the format “Zone name + tamper
alarm”.
Bedroom PIR tamper alarm.
For accessories assigned to zones that have
not been renamed, an SMS will be
sent under the format “Zone number +
tamper alarm”.
Zone 10 tamper alarm.
6
2. 067890022
3. 067890011
4. 067890000
5.
SMS numbers:
1. 067890033

2120
RenameRFIDTag
Send:
Rename RFID tag names:
1.
2.
3.
4.
Copy, paste, then edit
(case sensive):
Rename RFID tag names:
1. Tom
2. Nurse
3. Nancy
4. David
Ok
Note
The rst SMS number will receive SMS
nocaons when the system is disarmed
by RFID tag. To start receiving these
nocaons, you must rename the RFID
tags. Up to 4 RFID tags can be renamed.
Other tags will be aributed a number based
on the order of registraon to the control
panel. Refer to the instrucons on page 8
to learn how to register an RFID tag in the
control panel.
EntryandExitDelayTime
Send:
Entry delay me(0-300sec):0
Exit delay me(0-300sec):0
Copy, paste, then edit
(case sensive):
Ok
Note
This funcon can be used if you do not want to bring
a remote control or a RFID tag with you.
When you arm the system, the system will be
armed aer the delay set. When you disarm the
system, the system will be disarmed aer the
delay set.
When arming the system, you hear one beep
every second to remind you to leave. The beep
rhythm speeds up during the last 10 seconds.
If an intruder is detected, the alarm will be
delayed accordingly.
SirenVolumeandRingingTime
Send:
Siren volume(0=Mute,1=High):1
Siren ringing me(1-9min):3
Copy, paste, then edit
(case sensive):
Ok
DisarmPassword
Send:
Disarm password (4 digits):
1234
Copy, paste, then edit
(case sensive):
Disarm password (4 digits):
4321
Ok
131210 11
Entry delay me(0-300sec):10

Exit delay me(0-300sec):20
Siren volume(0=Mute,1=High):0

Siren ringing me(1-9min):5

2322
ChangeSystemLanguage
Send the code corresponding to the
language you want to set. For example,
for English, send “0001”.
0001
Ok
Refer to the table below for the full list of
languages:
0001 English
0002 French
0003 German
0004 Italian
Languages available may vary depending on
the version of your product.
RestoreSystemtoFactorySettingsbySMS
Send:
Ok
The sengs will be restored to default values.
Stored phone numbers and connected
accessories will not be deleted.
Note
Only stored numbers can send the SMS to
restore factory sengs.
Accessories
WirelessRemoteControl
Home Mode
Arm
SOS
Disarm
LED indicator
Armthesystem
Press the Arm button " " to arm the alarm
system. The LED indicator lights up (the
control panel beeps once). The system is
armed.
If an intruder is detected, the siren rings out.
(The siren turns o aer 5 minutes as per
default sengs.) In the meanme, the system
dials the stored phone numbers automacally.
Disarmthesystem
Press the Disarm button " " to disarm the
alarm system. The LED indicator turns off (the
control panel beeps twice). The system is
disarmed.
HomeMode
Press the Home Mode buon " " on the
remote control. The system state LED is on.
All the sensors in regular zones are armed
except those in the Home Mode zone.
The sensors in the Home Mode zone are
disarmed so that users can move inside their
home.
0000

2524
MuteMode
Press the Home Mode buon " " and
then the Arm " " or Disarm " " buon
immediately aer. Doing so, the control
panel does not beep when you arm or disarm
your system.
EmergencyMode
Regardless the status of the system, the
alarm is triggered when the SOS button "SOS"
is pressed on the remote control.
At the same time, the control panel sends a
notification by SMS ("RC-01 SOS", 01 being
the remote control's number) and dials the
pre-stored phone numbers.
Registerinthecontrolpanel
Refer to the instructions in the table on page 8 of this manual "Remote & Keypad".
Specicaons
Power supply
DC 3V (CR2025 buon baery x1)
Static current
≤10 uA
Operating current
≤7 mA
Transmission distance
≤ 80 m (in open area)
Radio-frequency:
433MHz (±75KHz)
Housing material
ABS plasc
Operating conditions
Temperature: -10°C ~ +55°C
Relave Humidity: ≤80%
(non-condensing)
Dimensions
57 x 31 x 11 mm
WirelessMotionDetector
Design
3
1
2
1. LED indicator
2. Detecon window
3. Bracket
LEDindicaons
Blinksconnuously: self-tesng
Blinksonce: an intruder is detected
Blinks twice: self-tesng is complete;
entering working mode.
Blinks once every 3 seconds: under-
voltage indicaon, the baeries must be
replaced. (You will be informed by SMS
when the baeries are low if the moon
detector is registered in the control panel.)
PCBLayout
Alarm zone
setup
Tamper
switch*
Infrared
sensor**
AA 1.5V LR6
Antenna
LED working
indicator
* Tamper switch
When the alarm system is armed, the tamper switch will trigger the alarm if the case is opened.
**Infrared sensor
Detects the infrared rays released by human body moon. Do not touch the surface. Keep the surface
clean.

2726
Usage
Open the case and remove the baery acvaon
strip. Self-tesng will start for 30 seconds.
When the sensor is in operaon, if it is triggered
more than twice within 3 minutes, it will switch
to standby mode to save power. If no movement
is detected within the next 3 minutes, the sensor
goes back to working mode.
Connect Button
Registerinthecontrolpanel
Navigate through the menu of the control panel and reach "ADD A NEW" (Wireless Sensor).
Press the Connect button at the back of the motion sensor or trigger the sensor (by moving in
front of it) to register the detector in the control panel.
Installaon
Avoid mounng the detector close to windows, air condioner, heater, refrigerator, oven,
sunshine and places where the temperature changes fast or where the air stream ows
frequently.
If two detectors are installed in the same detecon scope, adjust the locaon to avoid interferences
and false alarms.
Fix the bracket on the wall with
screws and aach the detector to the
bracket. Adjust the bracket to change
the detecon distance and angle. It is
recommended to mount the detector
2.2 m from the ground.
Top
Boom
Ground
2.2 m
The detector is more sensive to cross
movements than vercal movements.
Side view
Top view
Tesng
A. Aer the installaon, turn the detector on. Aer one minute of self-tesng, press the test
buon, walk in the scope of detecon and watch the LED indicator to make sure the detector
is working.
B. The LED indicator blinks once when body movement is detected.
C. Adjust the detector angle to achieve the best detecon performance.
Specicaons
Power supply
DC 3V (AA 1.5V LR6 Baeries x 2)
Static current
≤ 30uA
Alarm current
≤ 15 mA
Detection scope
8m / 110°
Transmission distance
≤ 80m (in open area)
Radio-frequency
433 MHz (±75 KHz)
Housing material
ABS plasc
Operating conditions
Temparature: -10°C~55°C
Relave humidity: ≤ 80% (non-condensing)
Detector dimensions (L x W x H)
107 x 53 x 32 mm
Bracket dimensions (L x W x H)
52 x 30 x 26.5 mm
DeteconScope
110°
Top view
0m 2m 4m 6m 8m
2m
0m
Side view

2928
WirelessDoor/WindowContact
Features
This Door / Window Contact can be installed on doors, windows, and any other objects that
open and close. The sensor sends a signal to the control panel when the magnet is separated
from the transmier.
Thanks to the tamper switch, any aempt to remove the cover of the Door / Window Contact
will trigger the alarm.
Design
Magnet
Transmitter
LED indicator
PCB Layout
LED working indicator
Zone setting
A23 12V battery
Tamper switch
LEDindicaons
Blinksonce: the door or window is open and the transmier sends a signal to the control panel.
Blinksquickly: Low power indicaon, the baeries must be replaced.
Registerinthecontrolpanel
Navigate through the menu of the control panel and reach "ADD A NEW" (Wireless Sensor).
Then separate the magnet from the transmitter to register the detector in the control panel.
To check if the registraon is complete, arm the system and separate the magnet from the
transmier again by opening the door or window on which it is installed. If the siren rings out,
the registraon is successful.
Installaon
- Open the case and remove the baery acvaon strip.
-Mount the sensor on the door and the magnet on the
door frame.
-Make sure the magnet is placed above the transmier.
-Mount the magnet max. 1 cm away from the transmier
and secure the transmier and magnet with double-sided
tape or screws.
-Avoid mounng the sensor in areas with a large amount of
metal or electrical wiring such as a furnace or ulity room.
Specicaons
Power supply
DC 12V (A23 12V Baery x 1)
Static current
≤ 30 uA
Alarm current
≤ 15 mA
Transmitting distance
≤80 m (in open area)
Radio-frequency
433 MHz (±75 KHz)
Housing material
ABS plasc
Operating conditions
Temparature: -10°C~55°C
Relave humidity: ≤ 80% (non-condensing)
Transmitter dimensions (LxWxH)
60 x 45 x 18 mm
Magnet dimensions (LxWxH)
45 x 19 x 17.5 mm

3130
RFIDTag
Features
The RFID tag enables you to disarm your system or unlock electronic door locks.
Registerinthecontrolpanel
Refer to the instructions in the table page 8 of this manual (“RFID TAG”).
Specicaons
Dimensions
45 x 30 x 7 mm
Troubleshootingandmaintenance
FAQ
Issue Cause of malfunction Solution
No response following
interacon with the
control panel
The control panel is switched o Open the baery compartment and
turn the power on
Electricity grid failure Contact your electricity provider
Backup baeries are empty Plug the AC adapter to an AC socket
Accessories cannot
connect to the control
panel
The control panel is not in
Connecon mode
Make sure the control panel is in
Connexion mode
Accessories have not been
triggered for connecon
Make sure the accessory is triggered so
to send a signal to the control panel
When aempng the
connecon, the control panel
beeps twice
The accessory has already been
connected
Make sure you do not trigger any
other accessory when connecng one
accessory to the control panel (e.g. do
not stay in the detecon scope of a
moon detector if it is not the one you
want to connect)
No response from the
control panel following
commands from the
remote control
The remote control has not been
connected to the control panel
Follow the instrucons in this manual
to connect the remote control to the
panel
Remote control is too far from
the control panel
Transmission distance of the remote
control: 80 m (in open area)
A signal repeater can be installed to
increase the transmission distance
RFID tag fails to disarm
the system
RFID tag has not been connected
to the control panel
Follow the instrucons in this manual
to connect the RFID tag to the control
panel
Impossible to access
sengs from the control
panel
You are not in the setup menu of
the LCD display
Enter your admin code followed
by “Enter“ to enter the setup
menu

3332
Precautions
For a safer use of the product and to opmize the lifespan of the product, we recommend you
to follow the precauons below:
- The wireless accessories must be connected to the control panel.
- Low power voltage may affect transmission distance.
- Do not press the SOS key on the remote control if it is unnecessary to avoid
disturbing neighborhood.
- Check the system regularly to make sure the system works properly.
- The control panel is neither waterproof nor moisture-proof, install it in a shady,
cool and dry place.
- The case of the control panel is made of ABS plastic. Keep away from bright light for
a longer lifespan.
- The control panel is not explosion-proof. Keep away from fire and flames.
- Install the control panel away from objects such as heater, air conditioner,
microwave oven etc. that generate heat or electromagnetic fields.
- Dispose of the batteries according to local regulations.
- Dismantling of this product must be done by professional personnel only.
Standards
This product bears the selecve sorng symbol for waste electrical and electronic equipment
(WEEE). This means that this product must be handled pursuant to European Direcve
2002/96/EC in order to be recycled or dismantled to minimize its impact on the environment.
For further informaon, please contact your local or regional authories.
Electronic products not included in the selecve sorng process are potenally dangerous for the
environment and human health due to the presence of hazardous substances.
In compliance with European laws. This product is in compliance with the essenal requirements
and other relevant provisions of Direcve 1999/5/EC.
This product was designed and manufactured in compliance with Direcve 2002/95/EC of the
European Parliament and of the Council on the restricon of use of certain hazardous substances
in electrical and electronic equipment (RoHS Direcve - RoHS) and is deemed to comply with
the maximum concentraon values set by the European Technical Adaptaon Commiee (TAC).
Manufactured in China.
ST-SK1-C-UM-EN20141120-1.0-W

ELBRO AG, Gewerbestrasse 4,
CH-8162 Steinmaur,
Switzerland
www.elbro.com