ADT Safewatch Plus Enterpreneur Security Systems User manual

ADT-1090-INT 7/25/00 3:12 PM Page 1

ADT-1090-INT 7/25/00 3:12 PM Page 2

Table of Contents
*
System Reference .................................................
2
Operating Your System
.........................................
3
ARMING
.......................................................................................
3
Arming The System Prior To Leaving
..................................... 3
Arming The System Without Leaving
..................................... 3
System Will Not Arm (Ready Light Off)
.................................. 4
DISARMING
...................................................................................... 5
Disarming Upon Entering The Premises
................................ 5
ALARM CONDITIONS
...................................................................... 6
What To Do If An Alarm Occurs
.............................................. 6
False Alarms
............................................................................. 6
THE EMERGENCY KEYPAD PANIC ALARMS
.............................. 7
Emergency Alarm Activation
................................................... 7
Resetting The Emergency Alarm
............................................
7
SPECIAL FEATURES
...................................................................... 8
Chime Mode
.............................................................................. 8
Force Arming
............................................................................ 8
Bypassing Zones
......................................................................
9
Key Switch Operation
............................................................ 10
Access
..................................................................................... 10
The Reset Key
.............................
..” ........................................ 10
Remote Programming
............................................................ 10
Audible Zone Testing
.............................................................
11
FIRE DETECTION
.......................................................................... 12
What To Do If The Fire Alarm Sounds
..................................
12
Fire Supervlsoryflrouble (Resetting Smoke Detectors).
..
..12
Emergency Evacuation Plan
............................... 13
Fire Prevention and Escape
.................................................. 14
Fire Protection
........................................................................ 15
Glossary
...............................................................
17
Index .....................................................................
18
1

Zone Identification Card
Space is provided for
recording the areas of
protection which are
;“““““““““‘““““““““’
: lndlvldual Zone Status
i
Ready status
If lighted, zone is not secure.
i
; /flight& the system is ready to be armed.
Chedc doors, windows, etc.
If not Iighted, one or more zones are faulted.
i
!
H not lighted, zone is secure.
i
, Indicator(s) of zonekl at fault will be lighted.
assigned to each zone. i___~bll~~~~~_~~~~_~_bypassed. !.
,.
,
Depending upon the
,
I
installation, this card pulls
1
,
\
out from the left or right
!
,
I
\ Armed Status
If lighted, the system is
armed.
condition exists.
Contact your security
representative.
side of the control station.
Trouble Indicator
/f /ighted, a trouble
Alarm Co:
Police:
Fire:
If not lighted, the
system is disarmed.
If b/inking, time is being
provided to exit the
building, after which the
system will be armed.
Alarm Indicator
If lighted, an alarm
has occurred.
Emergency Panic Keys
PANIC A =
PANIC B =
PANIC C =
NOTE: The Emergency Panic Keys may
or may not be active. Check with your
security representative for details.

Operating Your System
ARMING
Before the control can be armed, all of the intrusion zones must be secure as
indicated by the green READY indicator. If the READY indicator is off, one or
more zones are faulted. The indicator(s) corresponding to the faulted zone(s) will
light. Use the pull out zone I.D. card on the control station to determine the areas of
protection which are assigned to each of the six (6) zones, thencheckthe appropriate
doors and windows to see that they are closed.
1. Verify that the READY indicator is on.
2. Enter your User Code.
3. The control station will begin beeping and the red ARMED indicator will blink
to indicate that arming will take place after the exit time expires. (The ARMED
indicator will light steady after the system arms).
4. Leave the building immediately.
The control is programmed with an exit delay time which allows a specific amount
of time to leave through any delay defined intrusion detection zone without causing
an alarm. Be sure that you have been informed on routes to enter and exit from
without causing an alarm. If too much time is taken to exit, the beeping tone will
change to a steady tone, indicating the start of entry delay. Disarm the control and
start over to avoid a false alarm.
Your security system is divided into two areas of protection:
1.
2.
PERIMETER-Thefirstlineofdefense. Consistsofoneormorezoneswhich
detect intrusion through doors and windows.
INTERIOR - The backup or second line of defense. Consists of one or more
zones that detect intruders that have already entered the building. Interior
detection devices usually consist of motion detection devices, interior door
contacts, and under carpet sensors, designed to surprise the intruder.
prior to arming the control, you may first choose to turn off the interior protection,
allowing free movement within the building when armed.
3

;I Turning Off the lnterlor Zones and Entrance Delay
Control station key 4 may be used to turn the interior zones off prior to arming. This
will allow the system to alarm instantly if the entrance door is opened, while armed.
1. Press the 4 key and hold for three seconds.
2. When interior defined zones are turned off, the corresponding Zone indicators
will flash. The flashing will stop 30 seconds after the system is armed.
3. Arm the system by entering your User Code.
Note: Upon disarming, the interior zones automatlcally w-enable unless
your Installer has altered this feature through programming.
Q Automatic Interior Off/Delay Off
Your system may have been programmed to automatically turn the interior zones
off if you arm and do not leave the premises before the exit delay time expires. The
entrance delay may also be programmed to automatically turn off at this time. When
the system is disarmed, the interior and delay wilI return to their normal on or off
state. See your security representative for details.
Q Two Digit Arming
Your system may have been programmed with an abbreviated arming feature.
When this feature is enabled, only the first two digits of your User Code will be
required to arm the system and perform other features. Disarming however, will still
require the entire code sequence.
If the READY indicator is off, one or more detection devices such as a door or
window has been left open. The system cannot be armed. One or more of the six
ZONE indicators will also be lighted indicating the area of protection that is at fault.
Use the pull out zone I.D. card on the control station to define the area of protection
assigned to each zone.
NOTE: If an attempt Is made to arm the system with the READY light off,
a three second error tone wilt be emltted to alert you that the system did
not arm.
4

DISARMING
Your system is programmed with one or more entrance delay zones which allow
time to enter the premises without causing an alarm. Each delay door may be
programmed with a different entry time. Be sure to check with your installer.
Note: If your system has the “Interior Follower” feature enabled, all
interior designated zones automatically become delay zones whenever
you first enter through a delay zone. This allows you to walk In front of
motion detectors on the way to the control station after you enter.
1.
After entering the premises through a delay zone, the control station will sound
a continuous tone to remind you to disarm the system.
CAUTION: If the ALARM indicator is lighted, an alarm has occurred.
Leave the premises immediately and go to the nearest phone to contact
the appropriate authorities. Do not procede into the premises.
2. Enter your User Code.
3.
The red armed light should turn off indicating that the system is disarmed.
Testing the Burglar and Fire Alarm Audibles
UL listed burglar and fire alarm systems which have separate audible
sounding devices require a weekly test. Notify the Central Station or the
appropriate authorities before and after conducting the test. Use the
following procedures.
Burglar alarm
1.
Arm the system by following the instructions on the preceding pages.
2.
Upon expiration of the exit delay open a non-delayed door, window, or
motion detector. The sounding device will activate. To reset, follow the
instructions on disarming the system.
Fire alarm
1.
Follow the procedure for activation of the auxiliary alarms as outlined on
page 7 of this manual.
5

ALARM CONDITIONS
Whenever an alarm occurs, the ALARM indicator will light, the audible alarm will
sound (if applicable), and the control wilI communicate with the central station (if
this option was purchased).
NOTE: If upon returning to the premises it 1s discovered that an alarm has
occurred, DO NOT ENTER THE PREMISES.
Leave immediately and go to
the nearest phone and contact the appropriate authorities.
0 To reset the alarm:
1.
2.
Enter your User Code to reset the alarm.
The ALARM indicator will remain lighted.
If the alarm was activated through one of the six “hardwire” zones, the corre-
sponding ZONE indicator(s) will also be lighted, identifying the specific area
that was violated. Use the zone I.D. card to determine the area of protection
which corresponds to each zone.
If the alarm was activated manually by pressing one of the emergency keys, no
zone indicators will be lighted.
Press the “ * ” key to extinguish the ALARM indicator after determining the
type of alarm that occurred and area of protection involved.
A history of the alarm condition will be stored in the control’s memory and may be .
recalled at any time. See “Special Fkatures” for more information.
If for any reason a false alarm occurs, perform the following steps:
1.
2.
3.
4.
Enter your User Code.
The armed light should turn off.
Notify the appropriate authorities of the alarm immediately.
Press the “ * ”
key to extinguish the ALARM light. Use the zone I.D. card to
detemine the area of protection assigned to each zone.
6

THE EMERGENCY KEYPAD PANIC ALARMS
Your system may have been purchased with up to three emergency keypad panic
alarms. These may be used to activate an alarm in the event of a Fire, Hold-up, or
other emergency condition, as programmed by your installer. Each alarm is
activated by pressing the appropriate emergency panic key (located below the
numeric keys). Each alarm may be audible or silent. It may also be programmed
to report the condition to a central monitoring station. Check with your security rep-
resentative to determine the characteristics of your system.
Each of the three emergency panic keys (from left to right: A, B, and C) can initiate
a specific type of alarm as programmed and labeled by your installer.
To activate an Emergency Alarm:
1. Press the appropriate emergency panic key. The Emergency Alarm will
activate.
NOTE: Your lnstalter may have progmmmed the panic zones to ignore
momentaty key presses and to activate only by pressing and holding
pressed for three seconds (or pressing at least twice within three sec-
onds). Checkwlthyoutsecurttyrepresentatlveforthespeclflccharacter-
istlcs of your system
When an Emergency Alarm is activated, the ALARM indicator will be lighted
(unless your installer has programmed the alarm for silent or no control station in-
dication). To reset the alann:
1. Enter your User Code. Pressing the “ * ” key will extinguish the ALARM
indicator, if lighted.
Ahistoryofthelastalarmwillbestoredinthecontrol’smemoryandmayberecalled
if desired. (See “Special Features”).
7

SPECIAL FEATURES
The CHIME mode allows audible monitoring of zones while the system is
disarmed. When the CHIME mode is active, the control station sounder will beep
whenever a perimeter burglar defined zone (door, window, etc.) indicator is opened.
For example, the CHIME feature will cause the control station to beep two times
whenever the front door has been opened. Many businesses use this type of signal
to announce that a customer has entered. In a residential application, the CHIME
is useful for monitoring opening of doors by children.
0
1.
2.
3.
cl
1.
To Turn CHIME On
The system must be disarmed.
Press the “6” key and hold for three seconds. The control station will beep three
times to signify that the CHIME has been turned on.
The control station will now beep two times when any burglar zone is opened.
Note: The CHIME feature does not annunciate lntertor zones.
To Turn The CHIME Off
Press the “6” key and hold for three seconds. The control station will beep two
times to signify that the CHIME has been turned off.
Your system may be programmed for quick arming even with one or more zones
faulted. In this condition, when an attempt is made to arm the system with faulted
zones (READY light off), the control station will emit a three second error tone,
indicating that the system refused to arm. If a second attempt to arm is made within
eight seconds after the tone quits, all faulted zones will automatically be bypassed
and the system will Force Arm. Depending upon how your system was pro
grammed at the time of installation, force armed zones will either be permanently
bypassed until disarming or may return to operation when or if they become
operable.
8