Eldat Easywave RCP09 Series User manual

GB Power Plug Radio Call Detector RCP09
Models
Scope of Delivery
Safety Advice
Concept of Operations
The device may only be operated indoors as
acoustic signaller for notifications of alarm
signals and indicates the battery condition of
the tranmitters (evaluation undervoltage
telegram).
The outlet can only be used for mains voltage
consumers.
The manufacturer will not be liable for damage
caused by improper or inappropriate use.
Intended Use
Function
Function/Chapter
Operation
[press the button]
LED-view RCP09
Further actions
Teaching in the
call transmitter
1. button R (>1,6 s)
2. call transmitter
R
button
button
button flashes
button light up
R
R 4 s
after 20 s operation mode
teaching in furthertransmitter
cancel
Teaching in
acknowledgement
transmitter
1. Q (>1,6 s)
2. acknowl. transmitter
Q
button
button
button
button flashes
button light up
Q
Q 4 s
after 20 s operation mode
teaching in furthertransmitter
cancel
Selecting the
melody
button
button
button
R
R
R
1. Westminster
2. March
3. Ringing Bell
default settings
Setting the
volume/
flashlight
button
button
button
button
button
Q
Q
Q
Q
Q
1.
2.
3.
4. Quiet
5. Loud
Quiet and flashing light
Loud and flashing light
Muted (only flashing light)
default settings
Acknowledging
a call
button button
acknowl. transmitter
R, Q or
Deleting
individual
transmitters
1. R + Q (>1,6 s)
2. call- or acknowledgement
transmitter
R or Q
button button
button button
button flash
button R and Q light up
R and Q
4 s
after 20 s operation mode
cancel
deleting further
transmitters
Reset to Default
Settings
(RESET)
1. R + Q (>1,6 s)
2. R + Q (>1,6 s)
button R or button Q
button button
button button
button R and Q flash
button R and Q light up 4 s
after 20 s operation mode
cancel
default settings
Wall outlet
Loudspeaker
Button Q
Button R
Flashlight
RCP09 5001-12 868.30 MHz GB
RCP09 5001-14 868.30 MHz F/B
E
E
Power plug call signaller RCP09, operating
instruction
Please read these instructions
carefully before using the device!
We do not accept any liability for personal
injury or damage to property caused by
incorrect handling or non-observance of the
safety instructions!
Observe the valid laws and regulations as
well as the manufacturer's instructions for the
devices to be operated!
Frequency: 868.30 MHz
Modulation: FSK
: 230 V AC / 50 Hz
Current consumtion: max. 7 mA
Power consumption: approx. 0.3 W (stand by
: IP 20
: -20°C to +35°C
: 60%
:
122 x 50 x 75 mm
: 190 g
Operating voltage
Loudness: Distance 30 cm:
quiet: 75 dB, loud: 82 dB
Degree of protection
Operating
temperature
Max. relative air
humidity
Mains output Power plug
(non switchable)
Max. contact load:
GB 13 A / 230 V AC
F/B (PL) 16 A / 230 V AC
Dimensions (HxWxD):
Weight
Technical Details
Attention! Observe the admissible supply
voltage and the maximum contact load of the
wall outlet (see „Technical Details“)!
Do not plug one Call Detector into another.
The Call Detector is only de-energized when
it is disconnected from the mains supply.
The Call Detector must be easily accessible.
Have malfunctioning devices checked by the
manufacturers!
Do not open the appliance's casing!
Do not make any unauthorized alterations or
modifications to the unit!
The call signaller RCP09 serves for acoustic and
optic signalling of care requests. The call is
triggered by a handheld radio transmitter.
Þ
ringing tone Þ
The outlet of the call signaller can be used as an
outlet for any electric devices.
The melodies "Westminster", "March" or "Ring
tone" can be selected. By default, the call
signaller plays the "Westminster" melody.
Cyclic call signalling:
1. 1.5 min ringing tone 3 min break,
2. 1.5 min 3 min break,
3. 1.5 min 10 min break,
4. 1.5 min timeout.
The optic signal by the flashlight (if activated)
continues until the call is acknowledged. The call
can be acknowledged directly on the call
signaller or with an acknowledgement transmit-
ter.
It is also possible to evaluate an undervoltage
telegram indicating a low battery status of the
radio transmitters RT26, RT27 and RT28.
The weak battery status is indicated by the
alternate blinking of the buttons and can be
deactivated by pressing one of the two buttons.
ringing tone Þ
ringing tone Þ
Altogether 64 send codes can be programmed in
the call signaller (32 request codes and 32
acknowledgement codes).
Start-up
1. Plug the call detector into a
properly functioning earthed
outlet. You will hear a brief
acknowledgement signal.
2. Teach the coding of the call transmitter into
the call detector (see section "Teaching in the
call transmitter").
3. Teach the coding of the acknowledgement
transmitter into the call detector (see section
"Teaching in the acknowledgement trans-
mitter").
4. Select a new melody if desired.
5. Change the volume/flashlight combination if
desired.
Attention! Ensure an interference-free wireless
connection. Do not install the device in a
distribution box, metal housings or close to large
metal objects.
R
Q
GB F/B (PL)
Max. Contact load of sockets:
13 A 16 A

You can delete the code of a call or acknowledge-
ment transmitter you no longer need from the call
signaller as follows:
1. Keep both buttons on the call signaller
depressed at the same time until these start
blinking rapidly and the device will play an
acknowledgement signal.
2. Press the button of the transmitter until both
buttons are lit on the call signaller and the
acknowledgement beep sounds. The
transmitter was deleted. Proceed accordingly
to delete additional transmitters. If you do not
push a transmitter button within 20 seconds,
the call signaller switches automatically to
standby.
If you want to delete all saved transmitters,
proceed as described in the section "Restoring
the factory settings".
or
or
Reset to Default Settings
(RESET)
> 1,6 s
within
20 s
within
20 s
This function serves to transmit the coding of an
acknowledgement transmitter to the call
signaller.
1. Press the button Q until it blinks and the
device will play an acknowledgement signal.
If you want to cancel the teach-in process,
briefly press the button Q again.
2. Press the button of the acknowledgement
transmitter which you want to use to
acknowledge the call within 20 seconds until
the button Q of the call signaller lights up.
After approx. 4 seconds, you can teach in
additional acknowledgement transmitters.
If there is no input within 20 seconds, the call
signaller switches automatically to standby.
You can save at most 32 acknowledgement calls.
If all 32 memory slots are occupied, you will hear
a warning sound for approx. 2 seconds when
receiving another send code.
In case of a call by a call transmitter that was
already taught in, the teach-in process cannot be
activated.
Attention! It is not possible to teach in an already
taught in acknowledgement transmitter as call
transmitter.
Teaching in acknowledgement transmitter
You can turn off (acknowledge) the call signal
and the flashlight with the buttons R or Q or by
pressing a button on the acknowledgement
transmitter.
Acknowledging a call
Selecting the melody
This function serves to transmit the coding of the
call transmitter to the call signaller.
1. Press the button R until it blinks and the
device will play an acknowledgement signal. If
you want to cancel the teach-in process,
briefly press the button R again.
2. Press the button of the call transmitter within
20 seconds. If there is no input within 20
seconds, the call signaller switches
automatically to standby
If the coding was transferred, the button R is lit
for approx. 4 seconds. Afterwards you can
teach in additional call transmitters
In case of a call by a call transmitter that was
already taught in, the teach-in process cannot be
activated.
Attention! It is not possible to teach in an already
taught in call transmitter as acknowledgement
transmitter.
You can save at most 32 call transmitters. If all 32
memory slots are occupied, you will hear a
warning sound for approx. 2 seconds when
receiving another send code.
Teaching in the call transmitter
> 1,6 s
4 s 4 s
Setting the volume/flashlight
1. Briefly (<1.6 s) press the button Q. The
currently selected melody is played back at
the current volume.
2. Press the button Q again once the melody
has stopped. Now the device switches to the
next volume/flashlight combination.
If you do not press the button Q once again,
the selection is applied once the ring tone and
the blinking stop.
Loud +
flashing
light
Mute
Quiet
(no flashing
light)
Loud (no
flashing
light)
Quiet +
flashing
light
< 1,6 s
Press the
button Q
repeatedly
until the
desired
combination is
played.
Select the desired melody by pressing the button
R repeatedly
You have to wait until the selected melody stops
before you can select the next melody.
ca. 1,6 s
Attention! With a RESET all memorized call
and acknoledgement transmitters
1.
2.
as well as all
relevant settings are deleted and factory settings
are activated.
Keep both buttons on the call signaller
depressed at the same time until these start
blinking rapidly and the device will play an
acknowledgement signal.
Press both buttons again. It sounds the
acknowledgement beep and both bottuns
lights approx. 4 seconds. The call signaller
was return to factory settings.
> 1,6 s
> 1,6 s
To cancel press a button
To cancel press a button
1.
2.
3.
Westminster
March
Ring Bell
Deleting individual transmitters
Troubleshooting
Press the button
R repeatedly
until the desired
melody is
played.
1. Westminster
- The button R or Q blinks rapidly and the
warning beep sounds for 2 seconds: You have
tried to teach in an already taught in call
transmitter as acknowledgement transmitter or
an already taught in acknowledgement
transmitter as call transmitter.
- Warning beep for 2 seconds when teaching in a
call or acknowledgement transmitter: All
memory slots are occupied. Delete individual
transmitters and repeat the teaching in
process.
Disposal
Conformity
Customer Service
Put the packaging material into the
recycling bins for cardboard, paper and
plastics.
Dispose of the waste product via a collec-
tion point for electronic scrap or via your
specialist dealer.
Waste electrical products should not be
disposed of with household waste!
Hereby, ELDAT GmbH declares that the radio
equipment type RCP090 is in compliance with
Directive 2014/53/EU.
The full text of the EU declaration of conformity
is available at the following internet address:
www.eldat.de
For use in: EU/CH/FL/IS/N
Warranty
We will remedy defects on the device based on
material or production errors within the statutory
warranty period or exchange the device.
Any unauthorized tampering with, or modifica-
tions to, the product shall render this warranty null
and void.
General Information
If the device does not work properly despite
proper handing or in case of damage, please
contact your retailer.

You can delete the code of a call or acknowledge-
ment transmitter you no longer need from the call
signaller as follows:
1. Keep both buttons on the call signaller
depressed at the same time until these start
blinking rapidly and the device will play an
acknowledgement signal.
2. Press the button of the transmitter until both
buttons are lit on the call signaller and the
acknowledgement beep sounds. The
transmitter was deleted. Proceed accordingly
to delete additional transmitters. If you do not
push a transmitter button within 20 seconds,
the call signaller switches automatically to
standby.
If you want to delete all saved transmitters,
proceed as described in the section "Restoring
the factory settings".
or
or
Reset to Default Settings
(RESET)
> 1,6 s
within
20 s
within
20 s
This function serves to transmit the coding of an
acknowledgement transmitter to the call
signaller.
1. Press the button Q until it blinks and the
device will play an acknowledgement signal.
If you want to cancel the teach-in process,
briefly press the button Q again.
2. Press the button of the acknowledgement
transmitter which you want to use to
acknowledge the call within 20 seconds until
the button Q of the call signaller lights up.
After approx. 4 seconds, you can teach in
additional acknowledgement transmitters.
If there is no input within 20 seconds, the call
signaller switches automatically to standby.
You can save at most 32 acknowledgement calls.
If all 32 memory slots are occupied, you will hear
a warning sound for approx. 2 seconds when
receiving another send code.
In case of a call by a call transmitter that was
already taught in, the teach-in process cannot be
activated.
Attention! It is not possible to teach in an already
taught in acknowledgement transmitter as call
transmitter.
Teaching in acknowledgement transmitter
You can turn off (acknowledge) the call signal
and the flashlight with the buttons R or Q or by
pressing a button on the acknowledgement
transmitter.
Acknowledging a call
Selecting the melody
This function serves to transmit the coding of the
call transmitter to the call signaller.
1. Press the button R until it blinks and the
device will play an acknowledgement signal. If
you want to cancel the teach-in process,
briefly press the button R again.
2. Press the button of the call transmitter within
20 seconds. If there is no input within 20
seconds, the call signaller switches
automatically to standby
If the coding was transferred, the button R is lit
for approx. 4 seconds. Afterwards you can
teach in additional call transmitters
In case of a call by a call transmitter that was
already taught in, the teach-in process cannot be
activated.
Attention! It is not possible to teach in an already
taught in call transmitter as acknowledgement
transmitter.
You can save at most 32 call transmitters. If all 32
memory slots are occupied, you will hear a
warning sound for approx. 2 seconds when
receiving another send code.
Teaching in the call transmitter
> 1,6 s
4 s 4 s
Setting the volume/flashlight
1. Briefly (<1.6 s) press the button Q. The
currently selected melody is played back at
the current volume.
2. Press the button Q again once the melody
has stopped. Now the device switches to the
next volume/flashlight combination.
If you do not press the button Q once again,
the selection is applied once the ring tone and
the blinking stop.
Loud +
flashing
light
Mute
Quiet
(no flashing
light)
Loud (no
flashing
light)
Quiet +
flashing
light
< 1,6 s
Press the
button Q
repeatedly
until the
desired
combination is
played.
Select the desired melody by pressing the button
R repeatedly
You have to wait until the selected melody stops
before you can select the next melody.
ca. 1,6 s
Attention! With a RESET all memorized call
and acknoledgement transmitters
1.
2.
as well as all
relevant settings are deleted and factory settings
are activated.
Keep both buttons on the call signaller
depressed at the same time until these start
blinking rapidly and the device will play an
acknowledgement signal.
Press both buttons again. It sounds the
acknowledgement beep and both bottuns
lights approx. 4 seconds. The call signaller
was return to factory settings.
> 1,6 s
> 1,6 s
To cancel press a button
To cancel press a button
1.
2.
3.
Westminster
March
Ring Bell
Deleting individual transmitters
Troubleshooting
Press the button
R repeatedly
until the desired
melody is
played.
1. Westminster
- The button R or Q blinks rapidly and the
warning beep sounds for 2 seconds: You have
tried to teach in an already taught in call
transmitter as acknowledgement transmitter or
an already taught in acknowledgement
transmitter as call transmitter.
- Warning beep for 2 seconds when teaching in a
call or acknowledgement transmitter: All
memory slots are occupied. Delete individual
transmitters and repeat the teaching in
process.
Disposal
Conformity
Customer Service
Put the packaging material into the
recycling bins for cardboard, paper and
plastics.
Dispose of the waste product via a collec-
tion point for electronic scrap or via your
specialist dealer.
Waste electrical products should not be
disposed of with household waste!
Hereby, ELDAT GmbH declares that the radio
equipment type RCP090 is in compliance with
Directive 2014/53/EU.
The full text of the EU declaration of conformity
is available at the following internet address:
www.eldat.de
For use in: EU/CH/FL/IS/N
Warranty
We will remedy defects on the device based on
material or production errors within the statutory
warranty period or exchange the device.
Any unauthorized tampering with, or modifica-
tions to, the product shall render this warranty null
and void.
General Information
If the device does not work properly despite
proper handing or in case of damage, please
contact your retailer.

UM119969A 0617 GB
ELDAT GmbH
Im Gewerbepark 14
15711 Königs Wusterhausen
Germany
Phone: + 49 (0) 33 75 / 90 37-0
Fax: + 49 (0) 33 75 / 90 37-90
Internet: www.eldat.de
E-Mail: [email protected]