Eldat Easywave SM01 User manual

Technical Details
Frequency: 868.0 MHz
Radiated power: 0.49 mW
Modulation: FSK
Coding: Easywave A/B
Radio range: approx. 150 m in
 freeeldconditions
Detection angle: 180°
Detection area: crosswise: max. 12 m
frontal: max. 5 m
Installation height: 2 m to 4 m
Creep-under protection: yes
Brightnesssettingrange: 5to1000/∞Lux
Switching period range: 1 s to 20 min
Operating voltage: 230 V AC, +10 % to15 % 50 Hz
Power consumption: 0.8 W (standby)
Permissible ambient
temperature: max. -25 °C to +45 °C
Protection class: II
Degree of protection: IP55
Dimensions (l/w/h): 127/85/100 mm
Weight: 220 g
Contact load:
Switching capacity: 10 A (cosϕ= 1.0)
6 A (cosϕ= 0.6)
3 AX (cosϕ= 0.3)
Min. switching capacity: 10 mA
Switching contact: µ-contact 230 V AC
LEDlamps>2W<8W 90W
LEDlamps>8W 100W
Incandescent and
halogen lamp load: 2,300 W
Low-voltagehalogen
lamps: 2,300 VA
Fluorescent lamps
(low-loss series devices)
uncorrected: 400 VA
series corrected: 400 VA
parallel-corrected: 400VA(42μF)
Fluorescent lamps: 600 VA
(electronic series devices)
Compactuorescent
tubes: 150 W
(electronic series devices)
SM01 Motion detector
GB
Function
The SM01 is a wireless motion detector and wi-
red motion detector for automatic lighting control
based on movement and brightness. It is suitable
for wall mounting outdoors.
If a movement is detected while the measured
brightness is below the set threshold value, the
non-oating230Vrelayoutputofthemotionde-
tector switches ON for the set time.
In addition, a radio telegram (Easywave code A,
ON) is transmitted, which can be taught-in to Ea-
sywave receivers.
After the set time has elapsed, the relay output of
the motion detector switches OFF and Easywave
code B (OFF) is transmitted.
The device can be activated manually using a
break switch. After releasing the button (voltage
recovery), the device switches on (for at least 40
seconds, or for the time set on the device).
The motion detector has two potentiometers on
the underside of the sensor, which are used to ad-
just the time (minutes) and brightness (lux), etc.
The motion detector’s detection range is 12 m x
5 m, with a detection angle of 180°.
3m
5 m
12 m
180°
6 m
2-4 m
START UP
Mounting instructions
- The recommended mounting height is bet-
ween 2 metres and 4 metres.
- The sensor reacts to changing heat radiati-
on. The motion detector should therefore not
be mounted near heat sources, air currents
or moving objects.
- Do not direct motion detectors at objects
withhighlyreectivesurfaces(e.g.mirrors,
windows, etc.).
- Obstacles (e.g. walls, glass panes etc.) do
not radiate heat.
- Make sure that the wireless connection bet-
ween motion detector and receiver is unim-
peded. Avoid installing in the near of large
metallic objects.
Scope of Delivery
Motion detector, base, drilling template, moun-
ting kit, operating manual
Intended Use
Only use the device as a motion detector for swit-
ching Easywave radio receivers or for switching
directly connected electrical loads.
The manufacturer shall not be liable for any da-
mage caused by improper or non-intended use!.
Safety Advice
Before using the motion detector, care-
fully read through the operating instruc-
tions!
Caution! Electrical installation may
only be carried out by a qualied
electrician; otherwise there is a risk
of electric shock or re.
Also note the operating instructions of the
receiver(s)!
Donotmakeanymodicationstothedevice!
Have faulty devices checked by the manufac-
turer.
Only intended for installation out of arm‘s reach.
Sensor
Potentiometer for set-
ting brightness (lux) Potentiometer for
setting time (min)
Model
SM01E5001A01

Electrical connection Dismantling
- Disconnect the system from voltage and
secure it against being switched on again.
- Use a screwdriver to carefully loosen the side
locking hook and pull the device forward to
remove it.
230V
230V
Ø
6 mm
60 mm
230V
Click!Click!
A
Zeit (min)
Helligkeit (lux)
P
START UP
g. 3
230 V AC
Installation (seegure3)
Disconnect the system from voltage and
secure it against being switched on again.
Drillthexingholes(Ø6mm)intothewall
following the drilling template.
Remove the back of the motion detector (see
“Disassembly”) and pierce the membrane for
the cable throughput.
With no power running through them, run the
connection cables for the motion detector
and external button, if necessary through the
seals. Securely screw the back of the motion
detector to the wall.
Connect the connecting cables according to
thewiringdiagram(seegure2).
Place the motion detector on the base and
click it into place.
Set the Easywave receiver to learning mode
for the ON/OFF operating type, 2-button ope-
ration (see receiver operating instructions).
The receiver remains in learning mode for a
few seconds.

Switch the power supply for the motion detec-
tor back on while the receiver is still in learning
mode. The SM01 sends Easywave transmis-
sion code Aand is now taught-in to the recei-
ver.
Conduct a walking test (see “Adjusting the de-
tection zone”) and set your preferred time and
brightness settings (see “Settings”).
Do not start the walking test until the moti-
on detector has switched o󰀨!
Please note that after the power supply
has been switched on, the motion de-
tector remains switched on for at least
40 seconds, or for the time set on the
motion detector.
push button
(optional)
ON
g. 2
OFF
OFF
Time (min)
Brightness (lux)

Select brightness and time values
SET BRIGHTNESS (lux)
Youcansetdi󰀨erentbrightnessvalues(lux)with
the potentiometer.
If you wish to change the preset brightness
(15 lux default):
- Set potentiometer to desired brightness
(5 – 1000 lux).
or
Wish a specic brightness value to be learned
using the teach-in function:
- When the brightness is at your preferred
level, set the potentiometer to .
The value will be learned after 15 seconds.
- Leavepotentiometeratposition .
15 100
7
1
1
1
0
0
0
lux
teach-in 1000 Lu
x
5 Lux500 Lux
7 Lux100 Lux
10 Lux15 Lux50 Lux
15 Lux
SET TIME (min)
If the motion detector detects no further move-
ment,itswitcheso󰀨afterthesettime.
If you wish to change the preset time (2 min de-
fault):
- Set potentiometer to preferred
time (0.5 s – 20 min).
or
If you want to use the pulse function (e.g. for a
staircase light time switch):
- Set potentiometer to position . The motion
detectorisswitchedonfor<1s,theno󰀨for9
s. If it detects a movement again, it switches
on again for 1 s.
210
20
30s
test
min
test 20 min
1 s 15 mi
n
30 s 10 min
1 min 2 min 5 min
2 min
Adjust detection zone
WALK TEST
The walk test is used to test the detection range
and to restrict it if necessary.
After switching on the power supply,
the motion detector is switched on for
at least 40 seconds or for the set time.
Do not start the walking test until the
motion detector has switched o󰀨!
1. Set the potentiometer time (min) to test.
The motion detector now only reacts to move-
ment (independent of brightness).
Test
210
20
30s
test
min
2. Walk across to the detection area. After the
motion detector has detected a movement, it
switches on for 2 s. Note direction of motion
during the test.
0
2
Sec
2 sec
3. If you wish to adjust the detection range to
your requirements, realign the sensor head.
ALING THE SENSOR HEAD
The sensor head can be tilted down by 30°
30
30
and left and right by 90°.
90
90
Disposal
Waste electronic equipment must not be
disposed of with household waste!
Dispose of the waste product via collec-
tion facilities for electronic scrap or via
your specialist dealer.
Dispose of packaging material in the
recycling bins for cardboard, paper and
plastic.
Warranty
Within the statutory warranty period we undertake
to rectify free of charge by repair or replacement
any product defects arising from material or pro-
duction faults. Any unauthorized tampering with,
ormodications to, the productshall render this
warranty null and void.
Conformity
Hereby, ELDAT GmbH declares that the radio
equipment type ST01 is in compliance with Direc-
tive 2014/53/EU.
The full text of the EU declaration of conform-
ity is available at the following web address:
www.eldat.de
Customer service
If the device does not work properly despite
proper handling, or in the event of damage, please
contact the manufacturer or your retailer.
SETTINGS GENERAL INFORMATION

UM177147 1019 EN
ELDAT GmbH
ImGewerbepark14
15711 Königs Wusterhausen
Deutschland
Telefon: + 49 (0) 33 75 / 90 37-310
Telefax: + 49 (0) 33 75 / 90 37-90
Internet: www.eldat.de
E-Mail: [email protected]