eldoLED LINEARdrive 720D User manual

© 2016 eldoLED. All rights reserved. V4.1
More product documentation and eldoLED’s terms and conditions are available at www.eldoled.com.
Quick Start Guide LINEARdrive 720D (LIN720D3)
Connecting and configuring LINEARdrive 720D
ARemoving the cover
B Removing the strain reliefs
C Mounting the LINEARdrive
LINEARdrive
Intelligent LED Driver/Controller
IEC61347
EN55015, IEC61003, EN61547
130M
VDC in: SELV equivalent
: 99% typ.
T
a: -20°C to + 50°C
: +65°C
Tc
LINEARdrive 180D
Ext in +
Ext in
DMX in +
DMX in -
DMX in shield
LedSync thru +
LedSync thru -
LedSync shield
-
TC
1
2
3
Group
Group
Group
Group
LED supply +
4
12-28V / 6A Direct voltage controlled LED driver
TC
Group 1
LINEARdrive 720D
Group 1 GND
Group 2
Group 2 GND
Group 3
Group 3 GND
Group 4
Group 4 GND
Ext in +
Ext in
DMX in +
DMX in -
DMX in shield
LedSync out +
LedSync out -
LedSync shield
-
DALI out -
DALI out +
DALI in -
DALI in +
12-28V / 24A Direct voltage controlled LED driver
ø 4.2 mm / 0.17”
10 mm / 0.39”
30 mm / 1.18”
21.5 mm / 0.85”
110 mm / 4.33”
D Making the wire connections
M
2
1
0.2-1.5 mm
2
2
1
9 mm
0.35 inch
0.5-1.5 mm
2
AWG 20-16
9 mm
0.35 inch
AWG 24-16
VDC and LED connectors: Other connectors:
DMX in shield
DMX in +
DA +
DA
-
DA +
DA
-
DMX in -
Ext in +
Ext in -
{
12 -48VDC IN
-+
LedSync shield
LedSync out +
LedSync out -
LED groups
Power
supply
RR
R
R
LINEARdrive 720D
12-28V / 24W Direct voltage controlled LED driver
TC
Group 1
Group 1 GND
Group 2
Group 2 GND
Group 3
Group 3 GND
Group 4
Group 4 GND
Ext in +
Ext in -
DMX in +
DMX in -
DMX in shield
LedSync out +
LedSync out -
LedSync shield
DA -
DA +
DA -
DA +
EFastening the strain reliefs F Configuring the LINEARdrive
G Replacing the cover
LINEARdrive 180D
Ext in +
Ext in
DMX in +
DMX in -
DMX in shield
LedSync thru +
LedSync thru -
LedSync shield
-
TC
1
2
3
Group
Group
Group
Group
LED supply +
4
12-28V / 6A Direct voltage controlled LED driver
LINEARdrive
Intelligent LED Driver/Controller
IEC61347
EN55015, IEC61003, EN61547
130M
VDC in: SELV equivalent
: 99% typ.
T
a: -20°C to + 50°C
: +65°C
Tc
CAUTION: The device may only be connected and installed by a qualified electrician. All applicable regulations, legislation and building
codes must be observed. Incorrect installation of the device can cause irreparable damage to the device and the connected LEDs.

eldoLED B.V. Science Park Eindhoven 5125 5692 ED Son The Netherlands T [phone] [email protected]
eldoLED America. One Lithonia Way Conyers, GA 30012 USA T [phone] [email protected]
Quick Start Guide LINEARdrive 720D (LIN720D3)
Manual configuration
1. Select mode of operation
2. Set LED groups
3. Standalone Standalone Networked
operation or operation or operation
- Colour*- - Show - - DMX or DALI -
* The colour menu depends on the LED
group settings you have selected in step 2.
M
display off
SHOW
COLR
DMX
DALI
(5 sec)
M
+-
/
Set mode
MODE
SET
RGB
RGBW
RGBA
RRGB
RGGB
CCWW
CWWW
1-1L
2-2L
3-3L
4-4L
2-4L
1-4L
M
M
+
+-
/
LED groups
LED
+
OFF
POTM
10V
SWIT
display off
M
+-
/
External input
EXT INP
+-
/
LOG
LIN
Dimming curve
M
DIM CURV
+-
/
OFF
VID
COLR
WHIT
GLOW
M
M
M
M
+-
/
+-
/
1...512
Network resolution
DMX address
8 BT
16 BT
ADDR
DMX
RES
NETW
Interpolation
+-
/
AUTO
MANU
display off
M
NETW
Network setup
SET
+-
/
YES
NO
DMX termination
TERM
M
INTERPOL
00...20
M
display off
SHOW
M
M
M
-99...99
0...255
+-
/
+-
/
+-
/
Intensity
Speed
Show
SPD
INT
M
HUE
M
HUE
White
WHIT
M
M
+-
/
Intensity
0...255
INT
display off
+-
/
0...1535
+-
/
0...255
M
ADDR
NO
SETADDR
MM
display off
Nr. of ballasts
No address Address set
X BAL
M
Other features
Visual test run
Locking the configuration
Reset to factory defaults
M
display off
TEST
-
+
Test
++
R 1 sec
G 1 sec
B 1 sec
W 1 sec
RGBW 1 sec
R 1 sec
G 1 sec
B 1 sec
W 1 sec
RGBW 1 sec
+-
/
display off
M
LOCK
M
+
Lock driver
+(5 sec)
NO
SOFT
HARD
M
display off
RE - SET
-
+
Reset
++
M
(5 sec)
Press menu
PRES MENU