eldoLED LINEARdrive 100/A User manual

© 2012 eldoLED. All rights reserved. V1.5 1/4
M
370 mm / 14.57”
361 mm / 14.21”
ø 5.0 mm / 0.2”
41 mm
1.61”
30 mm / 1.18”
M
230 mm / 9.06”
15 mm / 0.59”
50 mm / 1.97”
15 mm / 0.59”
219.5 mm / 8.64”
ø 5.0 mm / 0.2”
80 mm
3.15”
30 mm / 1.18”
M
388 mm / 15.27”
42 mm
1.65”
354 mm / 13.94”
ø 5.0 mm / 0.2”
30 mm / 1.18”
Tech sheet LINEARdrive 100 ACSeries
Electrical Specifications
Input
• Voltage: 220 - 250 VAC, 50-60Hz
UL approved: 120 - 277 VAC, 50-60Hz
• Current, max: 1.05A at 120V/60Hz, 0.5A at 230V/50Hz,
0.45A at 277V/60Hz
Output
• Load per output:
RGBW @ 12V: 2.08A per output / RGBW @ 24V: 1A per output
RGB @ 12V: 2.76A per output / RGB @ 24V: 1.33A per output
For UL Class 2: RGBW @ 12V: 1.25A per output
RGB @12V: 1.66A per output
Absolute max for US: 5A common anode
• Power, max: 100W
General
• Standby power: < 0.5W
• Inrush current: 35A 240μs at 120V/60Hz,
67A 240μs at 230V/50Hz, 75A 240μs at 277V/60Hz
• Surge protection: 3kV (L to N), 4kV (L/N to GND)
• Power factor: > 0.94
• THD at 100% load, max: <10%
• DMX / RDM: USITT DMX512A and ANSI E1.20 (explore & address)
• DALI: IEC 62386-207
Use cases for 12V and 24V LED strips
12V RGB strip
3 LED outputs,
per output:
24V RGB strip
3 LED outputs,
per output:
12V RGB + white strip
4 LED outputs
per output:
24V RGB + white strip
4 LED outputs,
per output:
2 12V cool white + 2 warm white strips
4 LED outputs
per output:
Power, max: 100W 33W 33W 25W 25W 25W
Voltage, 12V or 24V 12V 24V 12V 24V 12V
Current, max 2.77A 1.33A 2A 1A 2A
Dimensions and weight
LINEARdrive 100/A
Weight: 890 g, 31.4 oz
LINEARdrive 100/S
Weight: 895 g, 31.6 oz
LINEARdrive 100/M
Weight: 770 g, 27.2 oz

© 2012 eldoLED. All rights reserved. V1.5 2/4
In Europe, use a H03V 0.75mm2power cable for
the 100/A and apply following strip lengths:
+
-
+
-
DALI
{
N
L
VAC
120-277
{
M
12V / 24V DIP switch
24V 12V
Non functional
4 LED groups, 4 control channels
RR
WRBG
R
R
Common anode
DMX in shield
DMX in
-
DMX in +
LedSync out shield
LedSync out
-
LedSync out +
Ext in
-
Ext in +
2
1
0.2-1.5 mm
2
2
1
9 mm
0.35 inch
0.5-1.5 mm
2
AWG 20-16
9 mm
0.35 inch
AWG 24-16
+
-
+
-
DALI
{
N
LVAC
120-277
{
2
1
0.2-1.5 mm
2
12V / 24V DIP switch
24V 12V
Non functional
RR
WRBG
R
R
Common anode
DMX in shield
DMX in
-
DMX in +
LedSync out shield
LedSync out
-
LedSync out +
Ext in
-
Ext in +
2
1
4 LED groups, 4 control channels
9 mm
0.35 inch
0.5-1.5 mm
2
AWG 20-16
9 mm
0.35 inch
AWG 24-16
12V / 24V DIP switch
24V 12V
Non functional
4 LED groups, 4 control channels
RR
WRBG
R
R
Common anode
DMX in shield
DMX in
-
DMX in +
Ext in
-
Ext in +
N
L
VAC
120-277
{
+
-
+
-
DALI
{
2
1
0.2-1.5 mm
2
2
1
9 mm
0.35 inch
0.5-1.5 mm
2
AWG 20-16
9 mm
0.35 inch
AWG 24-16
LedSync out shield
LedSync out
-
LedSync out +
Tech sheet LINEARdrive 100 ACSeries
Wiring data
• Wire type: solid or stranded copper
• Wire strip length: 9mm, 0.35 in.
• Wire core cross section:
0.5 - 1.5 mm2, AWG 20 - 16
• Maximum LED wiring length:
AWG value 20 19 18 17 16
Distance (m) 14 18 22 28 36
Distance (ft) 46 59 72 92 118
LINEARdrive 100/A
LINEARdrive 100/S
LINEARdrive 100/M
WARNING: Risk of electrical shock. May result in serious injury or death. Disconnect power before servicing or installing.
CAUTION: The device may only be connected and installed by a qualified electrician. All applicable regulations, legislation and build-
ing codes must be observed. Incorrect installation of the device can cause irreparable damage to the device and the connected LEDs.
CAUTION: Pay attention when connecting the LED groups: polarity reversal results in no light output and often damages the LEDs.
15 mm 6 mm

© 2012 eldoLED. All rights reserved. V1.5 3/4
Tech sheet LINEARdrive 100 ACSeries
Other information
Thermal
• Ta range: -40 ºC ... +50 ºC / -40 ºF ... +122 ºF
• Tc max: LINEARdrive 100/A 90 ºC / 194 ºF
LINEARdrive 100/M 85 ºC / 185 ºF
LINEARdrive 100/S 85 ºC / 185 ºF
• Typical self-rise of 30 ºC / 83 ºF at maximum load in free air
without heat sink
Certifications
• IEC 61347-1, IEC 61347-2-13, IEC 62384 + A1, EN 55015 + A1,
EN 55022 + A1, IEC 61000-3-2, IEC 61547, IEC 62386-207
•CE
• ENEC by VDE
• UL: Recognized Component for US and Canada (file no. E333135),
according to UL1310, UL8750. Class 2 output for US and Canada.
• Class A sound rating
• FCC: Title 47CFR Part 15 Class B
• The wiring inside electrical enclosures shall comply with
the 600V/105 ºC or higher.
Lifetime data
Life vs Ta
• Life expectancy of 50K hours at Ta of lower or equal to
50 ºC / 122 ºF
• MTBF: 480,000 hours
All measurements have been carried out at maximum load in
free air without heat sink.
All lifetime-related figures are the result of simulations.
Actual lifetime tests are ongoing.
30
60 55 50
45 40 35
86
140 131 122
113
104
95
30
35
40
45
50
55
60
Ta
Life [kHours]
ºC
ºF
Power factor data
Power factor vs Vout at Ta 25 ºC / 77 ºF
0
60 50 40 30 20 10
0.70
0.75
0.80
0.85
0.90
0.95
1.00
1.05
Vout [V]
120V - 60Hz
230V - 50Hz
277V - 60Hz
Pf
Europe, Rest of World North America
eldoLED Europe bv eldoLED America, Inc.
Luchthavenweg 18a 1762 Technology Drive #226
NL-5657 EB Eindhoven San Jose, CA 95110
The Netherlands USA
T: [phone] T: [phone]
F: [phone] F: [phone]
E: [email protected]
Sales support US/Canada: [email protected]
Sales support Rest of the World: [email protected]
Other documentation and support
Visit www.eldoled.com/ACsupport for further documentation such as
quick start guide, wiring diagram, tech sheet and 3D IGES files.
Warranty
eldoLED represents and warrants that for a period of 3 (three) years, as
of the date of invoice, Products materially meet the specifications and
specifically agreed upon quality, both as stated in the applicable
datasheet and/or written design-in specifications, or as stated in writing
otherwise by eldoLED, provided that these specifications are explicitly
designated by eldoLED as "warranted specifications".
For the complete warranty text, visit www.eldoled.com/terms.

© 2012 eldoLED. All rights reserved. V1.5 4/4
Tech sheet LINEARdrive 100 ACSeries
Notes