Electrolux Professional Lagoon TD6-7 User manual

Installation manual
Tumble dryer
TD6–7 Lagoon
Type N1...
Original instructions
438905990/EN
2022.09.09

Contents
Contents
1 Safety Precautions ..............................................................................................................................5
1.1 Gas heated tumble dryer ............................................................................................................7
1.2 General information ...................................................................................................................7
1.3 Commercial use only..................................................................................................................7
1.4 Ergonomics certification .............................................................................................................8
1.5 Symbols....................................................................................................................................8
2 Warranty terms and exclusions.............................................................................................................9
3 Technical data...................................................................................................................................10
3.1 Electric heated machines..........................................................................................................10
3.1.1 Drawing.........................................................................................................................10
3.1.2 Technical data................................................................................................................ 11
3.2 Gas heated machines ..............................................................................................................12
3.2.1 Drawing.........................................................................................................................12
3.2.2 Technical data................................................................................................................13
3.3 Machines with heat pump .........................................................................................................14
3.3.1 Drawing.........................................................................................................................14
3.3.2 Technical data................................................................................................................15
4 Setup ...............................................................................................................................................16
4.1 Unpacking...............................................................................................................................16
4.2 Recycling instruction for packaging ...........................................................................................17
4.3 Wheels ...................................................................................................................................18
4.4 Siting ......................................................................................................................................18
4.5 Drain connection (only for machines with heat pump) .................................................................19
4.6 Mechanical installation .............................................................................................................19
5 Evacuation system ............................................................................................................................20
5.1 Air principle .............................................................................................................................20
5.1.1 Electric- and Gas heated machines..................................................................................20
5.1.2 Machines with heat pump................................................................................................21
5.2 Fresh air..................................................................................................................................22
5.3 Exhaust duct ...........................................................................................................................22
5.4 Shared exhaust duct ................................................................................................................23
5.5 Exhaust dimensioning ..............................................................................................................23
5.6 Adjusting the air flow (not valid for tumble dryers with heat pump)................................................24
6 Electrical connection..........................................................................................................................28
6.1 Electrical installation ................................................................................................................28
6.2 Single-phase connection ..........................................................................................................28
6.3 Three-phase connection...........................................................................................................29
6.4 Electrical connections ..............................................................................................................29
7 Gas connection .................................................................................................................................30
7.1 Fasten the label .......................................................................................................................30
7.2 General...................................................................................................................................30
7.3 Gas installation........................................................................................................................31
7.4 Table of pressure and adjustment..............................................................................................31
7.5 Test run...................................................................................................................................32
7.6 Converting instructions.............................................................................................................33
7.7 Data label................................................................................................................................34
8 Reversing the door ............................................................................................................................35
9 At first power up ................................................................................................................................41
9.1 Select language.......................................................................................................................41
9.2 Set time and date.....................................................................................................................41
10 Function check..................................................................................................................................41
11 Disposal information..........................................................................................................................43
11.1 Disposal of appliance at end of life ............................................................................................43
11.2 Disposal of packing..................................................................................................................43
The manufacturer reserves the right to make changes to design and component specifications.

Installation manual 5
1 Safety Precautions
• Servicing shall be carried out only by authorized personnel.
• Only authorized spare parts, accessories and consumables shall be used.
• The machine is not to be used if industrial chemicals have been used for cleaning.
• Do not dry unwashed items in the machine.
• Items that have been soiled with substances such as cooking oil, acetone, alcohol, pet-
rol, kerosene, spot removers, turpentine, waxes and wax removers should be washed
in hot water with an extra amount of detergent before being dried in the machine.
• Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber
backed articles and clothes or pillows fitted with foam rubber pads should not be dried
in the machine.
• Fabric softeners or similar products should be used as specified by the fabric softener
instructions.
• The final part of a drying cycle occurs without heat (cool down cycle) to ensure that the
items are left at a temperature that ensures that the items will not be damaged.
• Remove all objects from pockets such as lighters and matches.
• WARNING. Never stop the machine before the end of the drying cycle unless all items
are quickly removed and spread out so that the heat is dissipated.
• Adequate ventilation has to be provided to avoid the back flow of gases into the room
for appliances burning other fuels, including open fires.
• Exhaust air must not be discharged into a flue which is used for exhausting fumes from
appliances burning gas or other fuels.
• The machine must not be installed behind a lockable door, a sliding door or a door with
a hinge on the opposite side to that of the machine in such a way that a full opening of
the machine is restricted.
• If the machine has a lint trap this has to be cleaned frequently.
• The lint must not be accumulated around the machine.
• DO NOT MODIFY THIS APPLIANCE.
• When performing service or replacing parts, the power must be disconnected.
• When the power is disconnected, the operator must see that the machine is discon-
nected (that the plug is removed and remains removed) from any point to which he has
access. If this is not possible, due to the construction or installation of the machine, a
disconnection with a locking system in the isolated position shall be provided.
• In accordance with the wiring rules: mount a multi-pole switch prior to the machine to
facilitate installation and service operations.
• WARNING: The appliance must not be supplied through an external switching device,
such as a timer, or connected to a circuit that is regularly switched on and off by a utility.
• If different rated voltages or different rated frequencies (separated by a /) are stated at
the machine data plate, instructions for adjusting the appliance for operation at the re-
quired rated voltage or rated frequency are stated in the installation manual.
• Stationary appliances not fitted with means for disconnection from the supply mains
having a contact separation in all poles that provide full disconnection under overvolt-
age category III, the instructions state that means for disconnection must be incorpo-
rated in the fixed wiring in accordance with the wiring rules.
• The openings in the base, shall not be obstructed by a carpet.

6Installation manual
• Oil-affected items can ignite spontaneously, especially when exposed to heat sources
such as in a tumble dryer. The items become warm, causing an oxidation reaction in
the oil. Oxidation creates heat. If the heat cannot escape, the items can become hot
enough to catch fire. Piling, stacking or storing oil-affected items can prevent heat from
escaping and so create a fire hazard.
• If it is unavoidable that fabrics that contain vegetable or cooking oil or have been conta-
minated by hair care products be placed in a tumble dryer they should first be washed
in hot water with extra detergent – this will reduce, but not eliminate, the hazard.
• Maximum mass of dry cloth: 8.0 kg (for gas heated tumble dryers).
• Maximum mass of dry cloth: 9.0 kg (for heat pump and electric heated tumble dryers).
• A-weighted emission sound pressure level at working stations: 70 dB(A).

Installation manual 7
1.1 Gas heated tumble dryer
• Before installation, check that the local distribution conditions, nature of gas and pres-
sure and the adjustment of the appliance are compatible.
• The machine is not to be installed in rooms containing cleaning machines with per-
chloroethylene, TRICHLOROETHYLENE or CHLOROFLUOROCONTAINING HY-
DROCARBONS as cleaning agents.
• If you can smell gas:
– Do not switch on any equipment
– Do not use electrical switches
– Do not use telephones in the building
– Evacuate the room, building or area
– Contact the person responsible for the machine
• Additional requirements for the following countries; AT, BE, BG, HR, CY, CZ, DK, EE,
FI, FR, DE, GR, HU, IS, IE, IT, LV, LT, LU, MT, NL, NO, PL, PT, RO, SK, SI, ES, SE, CH,
TR, UK:
– The appliance can be used in public areas.
– This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and knowl-
edge if they have been given supervision or instruction concerning use of the appliance
in a safe way and understand the hazards involved. Children shall not play with the ap-
pliance. Cleaning and user maintenance shall not be made by children without
supervision.
• Additional requirements for other countries:
– This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety. Children should be supervised to ensure that they
do not play with the appliance.
1.2 General information
Conditions for storage and transportation of the appliance should fulfil a temperature between -20℃/ + 70℃and
max Humidity of 95% RH.
In order to prevent damage to the electronics (and other parts) that may occur as the result of condensation, the ma-
chine should be placed in room temperature for 24 hours before being used for the first time.
Electric power supply should follow:
• Max range for each country rated voltage: -15% / +10%.
• Max range for each country rated frequency: ± 3 Hz.
• Dips/Interruption: 5 Dips/day (100% voltage lost, with 3-4 minutes duration).
A stable power supply is always the best. Fluctuations gives stress and additional load on all electric and electronic
components.
1.3 Commercial use only
The machine/machines covered by this manual is/are made for commercial and industrial use only.

8Installation manual
1.4 Ergonomics certification
The human body is designed for movement and activity but physical stress injuries as a result of static and repetitive
movements or unfavorable working postures may occur.
The ergonomic features of your product, the ones which may influence your physical and cognitive interaction with it,
have been assessed and certified.
A product which exhibits ergonomic features, in fact, shall fulfil specific ergonomic requirements, belonging to three
different areas: Polytechnic, Biomedical and Psychosocial (usability and satisfaction).
For each of these areas, specific tests with real users have been performed. The product was therefore compliant
with the ergonomic acceptability criteria requested by the standards.
In case several machines are managed by the same operator the repetitive movements will increase and as a conse-
quence of this the related biomechanical risk will increase exponentially.
The possible postural risks are the interaction with the door handle both in case the machine is placed directly on the
floor without a base and in case the machine is placed on top of a washing machine.
Follow the below recommendations to avoid, as much as possible, operators acquiring bodily injury.
• Place the machine on a base instead of directly on the floor so that the operator does not need to bend his/her
back unnecessarily when loading and unloading.
Minimum suggested height of bases is 300 mm.
• Move the control panel to the lower position in case the machine is placed on top of a washing machine.
• Make sure there are suitable trolleys or baskets for loading, unloading and transportation.
• Organize job rotation in the working place in the case several machines are managed by the same operator.
1.5 Symbols
Caution
Caution, hot surface
Caution, high voltage
Read the instructions before using the machine

Installation manual 9
2 Warranty terms and exclusions
If the purchase of this product includes warranty coverage, warranty is provided in line with local regulations and sub-
ject to the product being installed and used for the purposes as designed, and as described within the appropriate
equipment documentation.
Warranty will be applicable where the customer has used only genuine spare parts and has performed maintenance
in accordance with Electrolux Professional user and maintenance documentation made available in paper or elec-
tronic format.
Electrolux Professional strongly recommends using Electrolux Professional approved cleaning, rinse and descaling
agents to obtain optimal results and maintain product efficiency over time.
The Electrolux Professional warranty does not cover:
• service trips cost to deliver and pick up the product;
• installation;
• training on how to use/operate;
• replacement (and/or supply) of wear and tear parts unless resulting from defects in materials or workmanship re-
ported within one (1) week from the failure;
• correction of external wiring;
• correction of unauthorized repairs as well as any damages, failures and inefficiencies caused by and/or resulting
from;
– insufficient and/or abnormal capacity of the electrical systems (current/voltage/frequency, including spikes and/
or outages);
– inadequate or interrupted water supply, steam, air, gas (including impurities and/or other that does not comply
with the technical requirements for each appliance);
– plumbing parts, components or consumable cleaning products that are not approved by the manufacturer;
– customer’s negligence, misuse, abuse and/or non-compliance with the use and care instructions detailed within
the appropriate equipment documentation;
– improper or poor: installation, repair, maintenance (including tampering, modifications and repairs carried out
by third parties not authorized third parties) and modification of safety systems;
– Use of non-original components (e.g.: consumables, wear and tear, or spare parts);
– environment conditions provoking thermal (e.g. overheating/freezing) or chemical (e.g. corrosion/oxidation)
stress;
– foreign objects placed in- or connected to- the product;
– accidents or force majeure;
– transportation and handling, including scratches, dents, chips, and/or other damage to the finish of the product,
unless such damage results from defects in materials or workmanship and is reported within one (1) week of deliv-
ery unless otherwise agreed;
• product with original serial numbers that have been removed, altered or cannot be readily determined;
• replacement of light bulbs, filters or any consumable parts;
• any accessories and software not approved or specified by Electrolux Professional.
Warranty does not include scheduled maintenance activities (including the parts required for it) or the supply of
cleaning agents unless specifically covered within any local agreement, subject to local terms and conditions.
Check on Electrolux Professional website the list of authorized customer care.

10 Installation manual
3 Technical data
3.1 Electric heated machines
3.1.1 Drawing
BDG
H
3
I
J
4
A
1
2
C
E
F
fig.X01022
1 Operating panel
2 Door opening, ⌀392 mm
3 Electrical connection
4 Exhaust connection
ABCDE
mm 600 845 1050 580 385
F G H I J
mm 295 80 50 100 120

Installation manual 11
3.1.2 Technical data
Weight, net kg 97
Drum volume liters 135
Drum diameter mm 575
Drum depth mm 500
Drum speed, medium load rpm 53
Rated capacity, filling factor 1:18 (Max. load) kg 7.5
Rated capacity, filling factor 1:22 (Recommended load) kg 6.1
Heating: Electricity kW 6.0
Optimum air flow, 6.0 kW m3/h 155
Optimum static back pressure, 6.0 kW Pa 300
Maximum static back pressure, 6.0 kW Pa 310
Sound power/pressure level at drying* dB(A) 63/48
Heat emission of installed power, max % 15
* Sound power levels measured according to ISO 60704.
Connections
Air outlet ⌀mm 125

12 Installation manual
3.2 Gas heated machines
3.2.1 Drawing
BDH
I
4
J
K
5
A
1
2
C
E
F
3
G
L
fig.X01023
1 Operating panel
2 Door opening, ⌀392 mm
3 Electrical connection
4 Gas connection
5 Exhaust connection
ABCDE
mm 600 875 1050 580 385
F G H I J
mm 295 90 80 520 100
K L
mm 120 50

Installation manual 13
3.2.2 Technical data
Weight, net kg 97
Drum volume liters 135
Drum diameter mm 575
Drum depth mm 500
Drum speed, medium load rpm 53
Rated capacity, filling factor 1:18 (Max. load) kg 7.5
Rated capacity, filling factor 1:22 (Recommended load) kg 6.1
Heating: Gas kW 7.0
Optimum air flow m3/h 280
Optimum static back pressure Pa 200
Maximum static back pressure Pa 255
Sound power/pressure level at drying* dB(A) 63/48
Heat emission of installed power, max % 15
* Sound power levels measured according to ISO 60704.
Note!
The default gas appliances are built to run on either GNH or LPG gas where shall be installed at not over than
610 m (2001 ft) high altitude otherwise a kit for high altitude must be installed to the machine.
For the kit No. please refer to the spare parts list.
Connections
Air outlet ⌀mm 125
Gas connection 1/2” ISO 7/1–R1/2

14 Installation manual
3.3 Machines with heat pump
3.3.1 Drawing
BDG
H
I
4
A
1
2
C
E
F
3
J
fig.X01024
1 Operating panel
2 Door opening, ⌀392 mm
3 Electrical connection
4 Drain for condense water
ABCDE
mm 600 845 1050 580 385
F G H I J
mm 295 80 75 210 50

Installation manual 15
3.3.2 Technical data
Weight, net kg 119
Drum volume liters 135
Drum diameter mm 575
Drum depth mm 500
Drum speed, medium load rpm 53
Rated capacity, filling factor 1:18 (Max. load) kg 7.5
Rated capacity, filling factor 1:22 (Recommended load) kg 6.1
Sound power/pressure level at drying* dB(A) 63/48
Average heat emission per drying cycle used to assess ventilation need** kW 0.7
Ambient operating temperature ℃+10 – +45
* Sound power levels measured according to ISO 60704.
** For assistance with dimensioning necessary ventilation needs, contact authorized ventilation technician. For suffi-
cient ventilation all sources introducing heat need to be taken into account plus all other parameters effecting the
ventilation need. Climate zone, building parameters, room size, etc.
Connections
Pipe connection, condensed water ⌀mm 15
Heat pump
Type of refrigerant R134a
Amount of refrigerant kg 0.68
Fluorinated greenhouse gases
This product contains fluorinated greenhouse gases:
R134a: 0.680 kg
GWP 1430
CO2equivalent 0.9724 t
Hermetically sealed

16 Installation manual
4 Setup
4.1 Unpacking
Note!
For machines with heat pump; the machine must not be laid down or tilted more than 45°. If so, this might
damage the heat pump.
fig.X00529A
Remove the screws and the transportation bracket on each side of the machine.
Remove the machine from the pallet.
Note!
When moving the machine, handle it with care. The drum has no transport clamps.
2x 2x
fig.X01113
Place the machine on its final position.

Installation manual 17
4.2 Recycling instruction for packaging
4
5
6
7
3
1
2
fig.X02403
Fig. Description Code Type
1 Wrapping film LDPE 4 Plastics
2 Corner protection PS 6 Plastics
3 Cardboard packaging PAP 20 Paper
4 Pallet FOR 50 Wood
5Screw FE 40 Steel
6 Steel Bracket FE 40 Steel
7 Plastic bag PET 1 Plastics

18 Installation manual
4.3 Wheels
For ergonomic reasons the machine is equipped with wheels.
The wheels makes it easy to move the machine without lifting it.
The wheels can only be used as long as the feet of the machine is not lowered.
4x
fig.X01069
4.4 Siting
The figure shows recommended distance to walls and/or other machines.
A A
B
fig.X00959
A 5–500 mm (Min. 5 mm)
B 500 mm (Min. 200 mm)

Installation manual 19
Note!
The machine should be positioned so that there will be enough space for working, both for the user and
service personnel.
Respecting the given recommendations will provide easy access for maintenance and service operations.
In case of space limitations, it is possible to install machines without respecting to the given recommendations. If so,
keep in mind that it might be necessary to disconnect and move other machines to be able to reach and perform
service on affected machine.
4.5 Drain connection (only for machines with heat pump)
Connect a drain hose to the pipe (A) on the heat pump unit.
A
fig.X00695
Note!
The drain hose (A) must be positioned over the water level in the floor drain.
The drain must be lower than the drain outlet from the heat pump unit. If not the water will flow back into the
machine. Adjust with the feet.
The hose shall hang in a gentle arc.
4.6 Mechanical installation
Level the machine with the feet of the machine. The maximum height adjustment of the feet is 14 mm.
fig.W00177

20 Installation manual
5 Evacuation system
5.1 Air principle
Note!
It is very important that the machine gets enough fresh air in order to get the best drying result.
5.1.1 Electric- and Gas heated machines
The fan creates low pressure in the machine, drawing air into the drum via the heating unit. The heated air passes
through the garments and the drum holes and flows out through the filter positioned below the drum. The air is then
evacuated through the fan and exhaust system.
fig.X01075