Electrolux ELAP15 User manual

900523673 - UM (Jan. 2014) Printed in China
USA & Canada 1-800-896-9756
AIR CLEANER / PURIFICATEUR D’AIR / PURIFICADOR DE AIRE
Models ELAP15, ELAP30, ELAP40, ELAP45
EN • F • SP
airCleanerOG.qxp_AirFilter_English 1/20/14 12:05 PM Page 1

2
IMPORTANT SAFEG ARDS
www.electrolu .com
When using electrical appliances,
basic safety precautions should
always be followed, including the
following:
1. Read all instructions.
2. Do not use this appliance for other
than its intended use.
3. Close supervision is necessary
when any appliance is used by or
near children, or by others who may
need supervision.
4. To protect against electric shock, do
not place cord, plugs, or appliance
in water or other liquid.
5. Do not use outdoors or on wet
surfaces.
6. Do not use in humid places such as
bathrooms. f liquid enters the air
cleaner, turn it off and have it
inspected by an authorized
Electrolux service center.
7. Do not use near flammable gases.
8. Do not place directly beneath a
smoke detector, as this could
reduce the smoke detector’s
sensitivity.
9. Connect to a power supply only
as directed on the rating plate.
10. Do not operate any appliance with a
damaged cord or plug. f the
appliance malfunctions, or has been
damaged in any manner, return the
appliance to the nearest authorized
service center for inspection, repair,
or adjustment.
11. Do not pull or carry this equipment
by its cord. Do not use cord as a
handle, close a door on cord, or pull
cord around sharp edges or corners.
Do not let cord hang over the edge
of a counter or table where it can be
pulled on by children or tripped over
unintentionally.
12. Do not place the air cleaner near
a heater.
13. Keep cord away from heated
surfaces.
14. Do not put any object into openings.
Do not use with any opening
blocked; keep free of dust, lint, hair
and anything that may reduce
airflow.
15. Do not put objects on top of or
inside of unit, and do not block
the grills.
16. Do not use without filters in place.
17. Do not unplug the power cord
before air cleaner has cooled down.
18. Unplug from outlet when not in use
and before cleaning.
m portant safeguards . . . . . . . . . . . . . . 2-3
Air cleaner components . . . . . . . . . . . . . 4
Features . . . . . . . . . . . . . . . . . . . . . . . 5-6
Control panel . . . . . . . . . . . . . . . . . . . . . 6
Set-up . . . . . . . . . . . . . . . . . . . . . . . . . .7-9
Filter replacement . . . . . . . . . . . . . . .10-11
Care and maintenance . . . . . . . . . . . . . .11
Remote control . . . . . . . . . . . . . . . . . . . .12
Replacement parts . . . . . . . . . . . . . . . . .12
Trouble shooting . . . . . . . . . . . . . . . . . . .13
Warranty information . . . . . . . . . . . . . . 14
French user’s manual . . . . . . . . . . . 15-27
Spanish user’s manual . . . . . . . . . . 28-40
Contents
Register via the internet at: www.ele troluxapplian es. om/Owner-Support/Produ t-Registration
airCleanerOG.qxp_AirFilter_English 1/20/14 12:05 PM Page 2

3
!
Electrolu Customer Service 1-800-896-9756
Polarized plug
This appliance has a polarized plug
(one blade is wider than the other). To
reduce the risk of electric shock, this
plug will fit in a polarized outlet only
one way. f the plug does not fit fully
into the outlet, reverse the plug and
reinsert. f it still does not fit, contact a
qualified electrician. Do not modify the
plug in any way.
SAVE THESE INSTR CTIONS
Consumer Safety Information
THIS NIT IS FOR HO SEHOLD SE ONLY
!
CA TION
!
WARNING
Short cord instructions: Your appliance is fitted with a short power supply
cord as a safety precaution to prevent personal injury or property damage
resulting from pulling, tripping or becoming entangled with a longer cord. Do
not allow children to use or be near this appliance without close adult
supervision. f an extension cord is used, (1) the marked electrical rating of the
cord set or extension cord should be at least as great as the electrical rating of
the appliance, and (2) the cord should be arranged so that it will not drape over
the countertop or tabletop where it can be pulled on by children or tripped over.
Electrical power: f the electric circuit is overloaded with other appliances, your
appliance may not operate properly. t should be operated on a separate
electric circuit from other appliances.
IMPORTANT SAFEG ARDS
19. Do not use detergent to clean
the unit.
20. Do not wash and reuse the HEPA
filter or the High Deodorization Anti-
Odor Carbon Filter (ELAP40) or the
Carbon Pre-Filter (ELAP15 and
ELAP30). These filters are
non-washable.
21. Hold the handle on the back of the
unit to transport. Do not hold by the
front panel.
PROD CT SPECIFICATIONS
Model numbers . . . . . . . . . . . . . . . . . . .ELAP15D7PW, ELAP30D7PW, ELAP40D8PW, ELAP45D8PW
Power supply . . . . . . . . . . . . . . . . . . . .120V 60Hz
Motor . . . . . . . . . . . . . . . . . . . . . . . . . . ELAP15D7PW: BLDC Motor, max power 40W
ELAP30D7PW: BLDC Motor, max power 60W
ELAP40D8PW: BLDC Motor, max power 110W
ELAP45D8PW: BLDC Motor, max power 110W
Dimensions . . . . . . . . . . . . . . . . . . . . . . ELAP15D7PW: 19" H x 14" W x 9" D
ELAP30D7PW: 19" H x 16" W x 10" D
ELAP40D8PW: 22" H x 19" W x 12" D
ELAP45D8PW: 22" H x 19" W x 12" D
airCleanerOG.qxp_AirFilter_English 1/20/14 12:05 PM Page 3

4
AIR CLEANER COMPONENTS
A. Front panel
B. High Deodorization Anti-Odor Carbon
Filter (treated with anti-bacterial coating Cleancel®)
C. HEPA filter
D. Main body
E PlasmaWave®fan
F. Air outlet
G. Control panel
A. Front panel
B. Filter frame
C. Carbon Pre-Filter
(treated with anti-bacterial coating Cleancel®)
D. HEPA filter
E. Main body
F. PlasmaWave®fan
G. Air outlet
H. Control panel
A. Front panel
B. Filter frame
C. Carbon Pre-Filter
(treated with anti-bacterial coating Cleancel®)
D. HEPA filter
E. Main body
F. PlasmaWave®fan
G. Air Outlet
H. Control Panel
ELAP15 ELAP40
ELAP45
ELAP30
A. Front panel
B. Filter Cassette consists of the following:
B1. Washable Cleancel®Pre-Filter
(treated with anti-bacterial coating Cleancel®)
B2. Washable HEPA filter set
B3. Filter frame
B4. Washable Anti-Odor Carbon Filter
D. Main body
E. PlasmaWave®fan
F. Air outlet
G. Control panel
www.electrolu .com
airCleanerOG.qxp_AirFilter_English 1/20/14 12:05 PM Page 4

5
AIR CLEANER FEAT RES
ELAP15, ELAP30, ELAP40, ELAP45
CA TION: Fully assemble air filter before
using (See air cleaner set-up)
Note: Features vary according to model.
Quiet operation
With a four-speed fan with quiet operation
that is ideal for nighttime.
Air quality sensor
Built with an air quality sensor that detects
the presence of various pollutants in the air.
Light sensor
The built-in light sensor detects when the
room is dark and automatically dims the
lights of the control panel and lowers the
fan speed for quiet and energy-efficient
operation. Once the room is dim, the fan
does not increase speed despite what
the air quality sensor detects.
Automati air leaning (AUTO mode)
The air quality sensor detects the amount
of impurities in the air and automatically
adjusts the fan speed accordingly to keep
your air purified.
ELAP15, ELAP30, ELAP40 –
4 stage filtration
The Carbon Pre-Filter (High Deodorization
Anti-Odor Carbon Filter for ELAP40)
absorbs gases and odors such as those
generated by cigarette smoke, pets,
ammonia or cooking. For best performance,
replace every 3 months (every 12 months for
High Deodorization Anti-Odor Carbon Filter).
The Cleancel®anti-microbial coating
prevents the growth of micro organisms.
The HEPA filter captures 99.9% of particles
and impurities as small as 0.3 microns,
including smoke, dust, pollen, and other
allergens. Replace when the CHECK F LTER
indicator light turns on. PlasmaWave®
Technology uses positive and negative ions
to clean the air of harmful pollutants
breaking them down and converting them to
naturally occurring oxygen and hydrogen.
ELAP45 – 5 stage filtration
The first stage of filtration consists of a
pre-filter coated with Cleancel.
®The
Cleancel®anti-microbial coating prevents
the growth of micro organisms. The
activated Anti-Odor Carbon Filter
specializes in absorbing odors such as
those caused by cigarettes, pets, and
cooking. The Anti-Odor Carbon Filter will
also trap gases such as ammonia and
formaldehyde. The HEPA filter set captures
99.9% of particles and impurities as small
as 0.3 microns, including smoke, dust,
pollen, and other allergens. PlasmaWave®
Technology uses positive and negative ions
to clean the air of harmful pollutants
breaking them down and converting them to
naturally occurring oxygen and hydrogen.
The Cleancel® Pre-Filter set, HEPA filter and
Anti-Odor Carbon Filter are washable.
Electrolu Customer Service 1-800-896-9756
airCleanerOG.qxp_AirFilter_English 1/20/14 12:05 PM Page 5

6
CONTROL PANEL
. Air Quality Sensor: Automatically monitors the air quality level and
adjusts fan speed accordingly when in “AUTO.”
J. Reset: Resets the “Check Filter” indicator light.
K. Check Filter Indicator: Signals when to replace filters.
L. Auto: Automatically adjusts the fan speed according to the amount
of impurities.
M. PlasmaWave®:Shows that the technology is active.
N. Air Quality Indicator: Lights indicate the quality of the air.
O. Fan Speed Indicator: Shows current fan speed setting ( Turbo / High / Low / Quiet) .
P. Fan Speed Selector: Adjusts fan speed setting (Turbo / High / Low / Quiet) .
Q. On-Off: Turns the unit “On” and “Off.”
R. Light Sensor: Dims the control panel lights and sets the fan speed to
“Quiet” when the room is dark (only works when in “AUTO”).
ELAP15, ELAP30, ELAP40, ELAP45
www.electrolu .com
airCleanerOG.qxp_AirFilter_English 1/20/14 12:05 PM Page 6

Place the unit away from drafty areas, as the sensors may not react
accurately. Do not place near curtains, furniture, or other items that
might inhibit air flow. Place the unit on a stable surface.
1. Remove protective film from the control panel.
2. Remove the front panel by pulling gently from the top portion of
the panel.
3. Remove the HEPA filter and the Carbon Pre-Filter from the plastic
wrapper.
4. nstall the HEPA filter with the arrow showing “air flow” pointing in toward
the back of the air cleaner; the white tabs at the top and bottom of the
HEPA filter will point out to the front of the unit.
5. nstall the Carbon Pre-Filter in front of the HEPA filter.
6. Replace the front panel by hooking the panel on the bottom of the unit.
7. Plug the power cord into a wall outlet.
8. Press and hold the POWER button until a short “beep” sounds.
9. The air cleaner will take 3-4 minutes to calibrate the air quality sensor.
During this time the sensor lights will flash on and off. Once the sensor
has calibrated, the lights will be on “AUTO” mode.
7
AIR CLEANER SET- P
ELAP15, ELAP30
Electrolu Customer Service 1-800-896-9756
airCleanerOG.qxp_AirFilter_English 1/20/14 12:05 PM Page 7

8
AIR CLEANER SET- P
ELAP40
Place the unit away from drafty areas, as the sensors may not react
accurately. Do not place near curtains, furniture, or other items that
might inhibit air flow. Place the unit on a stable surface.
1. Remove protective film from the control panel.
2. Remove the front panel by pulling gently from the top portion of
the panel.
3. Remove the HEPA filter and the High Deodorization Anti-Odor Carbon
Filter from the plastic wrapper.
4. nstall the HEPA filter with the arrow showing “air flow” pointing in toward
the back of the air cleaner; the white tabs at the top and bottom of the
HEPA filter will point out to the front of the unit.
5. nstall the High Deodorization Anti-Odor Carbon Filter in front of the
HEPA filter.
6. Replace the front panel by hooking the panel on the bottom of the unit.
7. Plug the power cord into a wall outlet.
8. Press and hold the POWER button until a short “beep” sounds.
9. The air cleaner will take 3-4 minutes to calibrate the air quality sensor.
During this time the sensor lights will flash on and off. Once the sensor
has calibrated, the lights will be on “AUTO” mode.
www.electrolu .com
airCleanerOG.qxp_AirFilter_English 1/20/14 12:05 PM Page 8

9
AIR CLEANER SET- P
Electrolu Customer Service 1-800-896-9756
ELAP45
Place the unit away from drafty areas, as the sensors may not react
accurately. Do not place near curtains, furniture, or other items that
might inhibit air flow. Place the unit on a stable surface.
1. Remove protective film from the control panel.
2. Remove the front panel by pulling gently from the top portion of
the panel.
3. Remove the Filter Cassette and remove the plastic wrapper
from it.
4. nstall the Filter Cassette by gently sliding the entire cassette into
the air cleaner. t should fit perfectly.
5. Replace the front panel by hooking the panel on the bottom of the unit.
6. Plug the power cord into a wall outlet.
7. Press and hold the POWER button until a short “beep” sounds.
8. The air cleaner will take 3-4 minutes to calibrate the air quality sensor.
During this time the sensor lights will flash on and off. Once the sensor
has calibrated, the lights will be on “AUTO” mode.
airCleanerOG.qxp_AirFilter_English 1/20/14 12:05 PM Page 9

10www.electrolu .com
FILTER REPLACEMENT
ELAP15, ELAP30
There are two separate filters:
Carbon Pre-Filter and HEPA filter.
• The Check Filter indicator will signal when
to replace the HEPA filter. The replace-
ment period will vary depending on the
hours of usage, air quality, and location
of the unit. However, in most cases of
normal use, the filter will need to be
replaced annually.
• For best performance, change the Carbon
Pre-Filter every three months.
The filters should be disposed off when
changed. Do not wash and reuse the HEPA
filter or the Carbon Pre-Filter as they will
not work effectively.
CA TION: Turn off the air cleaner
and unplug the electrical cord before
performing any maintenance.
Carbon Pre-Filter repla ement
1. Turn off the air cleaner and unplug the
electrical cord.
2. Remove the front panel by pulling gently
from the lower portion of the panel. Do
not force, the panel should remove
easily.
3. Remove the Carbon Pre-Filter by gently
pulling out from the bottom and down
from the top.
4. Remove the Carbon Pre-Filter and
dispose of it.
5. Remove a replacement Carbon Pre-Filter
from the resealable plastic bag and
reseal to maintain the freshness
of the remaining filter.
6. nstall the Carbon Pre-Filter.
!
ELAP40
CA TION: Turn off the air cleaner
and unplug the electrical cord before
performing any maintenance.
!
There are two separate filters:
High Deodorization Anti-Odor
Carbon Filter and HEPA filter.
• The Check Filter indicator will signal when
to replace the HEPA filter. The replace-
ment period will vary depending on the
hours of usage, air quality, and location
of the unit. However, in most cases of
normal use, the filter will need to be
replaced annually.
• For best performance, change the High
Deodorization Anti-Odor Carbon Filter
every 12 months. The filters should be
disposed off when changed. Do not wash
and reuse the HEPA filter or the High
Deodorization Anti-Odor Carbon Filter as
they will not work effectively.
High Deodorization Anti-Odor
Carbon Filter repla ement
1. Turn off the air cleaner and unplug the
electrical cord.
2. Remove the front panel by pulling gently
from the lower portion of the panel. Do
not force, the panel should remove
easily.
3. Remove the High Deodorization Anti-
Odor Carbon Filter by gently pulling out
from the bottom and down from the top.
4. Remove the High Deodorization Anti-
Odor Carbon Filter and dispose of it.
5. Remove a replacement High Deodoriza-
tion Anti-Odor Carbon Filter from its
plastic bag.
6. nstall the High Deodorization Anti-Odor
Carbon Filter.
airCleanerOG.qxp_AirFilter_English 1/20/14 12:05 PM Page 10

11
FILTER REPLACEMENT
ELAP45
CA TION: Turn off the air cleaner
and unplug the electrical cord before
performing any maintenance.
!
ELAP15, ELAP30, ELAP40, ELAP45
CA TION: Turn off the air cleaner
and unplug the electrical cord before
performing any maintenance.
!
Filter Service life Cleaning Cycle How to clean
Washable
Cleancel®
Pre-Filter
12 months Every 3
months
Clean with vacuum
cleaner or soft
brush. Use warm
water when the
filter is very dirty.
Washable
HEPA
Filter set
12 months Every 3
months
Soak the filter into
warm water for 30
minutes and dry it
in the shade for
24 hours.
Washable
Anti-Odor
Carbon
Filter
12 months Every 3
months
Soak the filter in
warm water for 30
minutes and dry it
in the shade for
24 hours.
Filter
Cassette
12 months – –
The Check Filter indicator will signal when
to replace the Filter Cassette. The
replacement period will vary depending on
the hours of usage, air quality, and location
of the unit. However, in most cases of
normal use the filter will need to be
replaced annually. This Filter Cassette
should be disposed of when changed.
Filter Cassette repla ement
1. Turn off the air cleaner and unplug the
electrical cord.
2. Remove the front panel by pulling gently
from the top portion of the panel.
3. Remove the Filter Cassette by gently
pulling out from the bottom and down
from the top.
4. Remove all the filters from the plastic
frame and dispose of the filters only.
Keep the frame.
5. Remove the replacement filters from the
plastic bag and replace them.
6. Replace the front panel by hooking the
panel on the bottom of the unit.
7. Plug in air cleaner and press POWER
button until short “beep” sounds.
8. Press the RESET F LTER button by
gently inserting a paperclip into the
RESET F LTER hole on the
control panel. The light will
flash 5 times before a
“beep” sounds to indicate
the filter has been reset.
CARE AND MAINTENANCE
• Clean unit as necessary by wiping with a
dry, soft cloth; for stubborn stains, use a
warm, damp cloth.
• Do not use volatile fluids such as
benzene, paint thinner or scouring
powder, as they may damage the surface.
Keep the unit dry.
• Lightly vacuum air quality sensor
every three months.
Electrolu Customer Service 1-800-896-9756
airCleanerOG.qxp_AirFilter_English 1/20/14 12:05 PM Page 11

Electrolu replacement parts
Fits models Part number
1 HEPA Filter and 4 Carbon Pre-Filters
ELAP15
EL041
1 Filter Frame
ELAP15
68691
1 HEPA Filter and 4 Carbon Pre-Filters
ELAP30
EL042
1 Filter Frame
ELAP30
68692
1 HEPA Filter and 1 High Deodorization Anti-Odor Carbon Filter
ELAP40, ELAP45
EL043
1 Washable HEPA Filter Set, 1 Washable Anti-Odor Carbon Filter
and 1 Cleancel®Pre-Filter
ELAP40, ELAP45
EL044
1 Filter Frame
ELAP40, ELAP45
68694
12www.electrolu .com
DISPOSAL
ELAP30, ELAP40, ELAP45
REMOTE CONTROL
Operate the remote control facing the air
cleaner. Operate within 18 feet / 6 metres of
the air cleaner. The remote control has a
separate wall-mountable storage
cradle that can be conveniently
attached to any wall using a screw.
S. POWER: Use the power button
to turn the power on and off. A
short “beep” will sound when
the unit turns on and off.
T. A TO mode: Use the AUTO
button to put air cleaner in
AUTO mode.
U. FAN SPEED: By pressing up or down,
the unit will change fan speeds and enter
into manual mode.
V. T RBO: Use this button to switch from
automatic operation and start the
maximum amount of room air cleaning
and air movement. t will remain in Turbo
speed until changed into Auto or
manual mode.
Battery repla ement
1. Squeeze tabs of battery cover
and at the same time pull cover
out of remote.
2. nsert battery as shown and
close battery cover.
3. Always use 3V lithium battery CR2025.
ncorrect battery usage may cause
battery fluid leakage and/or damage.
Recycle the materials with the recycle
symbol. Put the packaging in
applicable containers to recycle it. Help
protect the environment and human health
and to recycle waste of electrical and
electronic appliances.
Do not dispose appliances marked
with this symbol with household waste.
Return the product to your local
recycling facility or contact your municipal
office.
To order replacement parts, visit us online at www.electrolux.com or call 1-800-896-9756.
airCleanerOG.qxp_AirFilter_English 1/20/14 12:05 PM Page 12

13
TRO BLE SHOOTING
Electrolu Customer Service 1-800-896-9756
Occurrence Possible causes / solution
Can I wash my filter? No, the filters that come with the unit will be ruined by water. eplace with new
washable filter. (ELAP45 filters are washable.)
Can I vacuum my filter? No, vacuuming will spread the dust back into the air. eplace with new filter. (ELAP45
Washable Pre-Filter can be cleaned with a vacuum cleaner or soft brush.)
There is an odor coming
from my new unit.
The unit has been concealed in a tightly wrapped package of corrugated cardboard
and plastic. It may give off an odor; this should wear off in several days.
Will this clean a bigger area
than what it is rated for?
CAD ratings are provided from a controlled testing environment, if that environment
changes, it can affect the performance. If you have a slightly larger room than what the
CAD rating is, it will help improve the air, but take longer.
Where should I place
the unit?
Allow proper air circulation around the sides and in front of the unit. If there
are doors or hallways it may reduce the airflow.
The AIR QUALIT light
is orange or red, but the
air seems clean.
• Clear the sensor with a vacuum cleaner, as it may be blocked or clogged.
• Sometimes a can of compressed air may unclog the dust in the sensor.
You can see dust in the air
or on my furniture.
The unit will capture most dust and particles, however with opening doors, windows,
central HVAC etc., there may still be some level of dust that you can see.
There is nothing holding the
filters in place.
The filters are meant to rest inside the unit. Once the unit is turned on, the force of air
pulled through the machine will create a tight seal of the filters.
I can hear revving of the
fan motor.
This is normal, especially at night when all environmental sounds are quiet, you may
hear the motor running in repetition.
The unit has stopped
removing odors effectively,
or is emitting an odor.
• Make sure the air quality sensor is not blocked or clogged.
• Move the unit closer to the offending odors.
• eplace filters more frequently. They may have reached their capacity to absorb
pollutants.
The CHECK FILTER
indicator remains lit after
replacing the HEPA filter.
Press the RESET FILTER button by gently inserting a paper-clip into the
RESET FILTER button hole. Hold for 3-5 seconds until a “beep” sounds to indicate the
unit has been reset.
Can I turn off the sleep
mode?
No, but you can manually push to the fan speed you prefer which will stay at that
speed until you change it.
Unit makes a ticking sound. This is due to PlasmaWave®technology, it may come and go, but as long as the
PlasmaWave®light is on, the function is working.
The remote control
does not work.
• Make sure the remote control battery is inserted correctly.
• eplace a worn-out battery.
• Make sure that the remote control has a clear line of sight to the air cleaner.
The air quality light is white,
but there is still dust/odor.
• Make sure the sensor is not blocked or clogged.
• eplace the filter.
The unit is running on high
all the time.
• Clear the sensor with a vacuum cleaner, as it may be blocked or clogged.
• Sometimes a can of compressed air may unclog the dust in the sensor.
The CHECK FILTER
indicator remains lit after
replacing the Filter Cassette.
Press the RESET FILTER button by gently inserting a paper-clip into the
RESET FILTER button hole. Hold for 3-5 seconds until a “beep” sounds to
indicate the unit has been reset.
ELAP15, ELAP30, ELAP40, ELAP45
airCleanerOG.qxp_AirFilter_English 1/20/14 12:05 PM Page 13

14
SMALL DOMESTIC APPLIANCE WARRANTY
Your appliance is covered by a one year
limited warranty. For one year from your
original date of purchase, Electrolux will repair
or replace the appliance or parts, at
Electrolux’s option, that prove to be defective
in materials or workmanship when the
appliance is installed, used, and maintained in
accordance with the provided instructions.
Labor and all costs associated with returning
the appliance or parts to us and our returning
the appliance or parts to you are excluded
under this warranty. As a matter of warranty
policy, Electrolux will not refund the
consumer’s purchase price. f a product or
part under warranty is no longer available,
Electrolux will replace with a comparable
product of equal or greater value.
Exclusions: This warranty does not
cover the following:
1 Products with original serial numbers that
have been removed, altered or cannot be
readily determined.
2 Products that have been transferred from
the original owner to another party or
removed outside the USA or Canada.
3 Rust on the interior or exterior of the unit.
4 Products purchased “as-is”.
5 Food loss due to product failure.
6 Products used in a commercial setting or
anything but single family household use.
7 Labor or service visits under any
circumstance.
8 Glass parts or containers, filters, non-stick
surfaces.
9 Ordinary wear and tear.
10 Damages caused by improper use,
installation, or service; use of parts other
than genuine Electrolux parts; negligence;
abuse; misuse; inadequate or excessive
power supply; accidents; fires; or acts of
God.
Keep your receipt or some other appropriate
payment record to establish the warranty
period. Should warranty service be required,
you must show proof of purchase.
If you need service:
To obtain warranty service in the USA or
Canada, call 1-800-896-9756. Please have
the model number, serial number, and date of
purchase information available.
DISCLAIMER OF IMPLIED
WARRANTIES; LIMITATION OF
REMEDIES:
CUSTOMER’S SOLE AND EXCLUS VE
REMEDY UNDER TH S L M TED WARRANTY
SHALL BE, AT ELECTROLUX’S SOLE
D SCRET ON, PRODUCT OR PART REPA R
OR REPLACEMENT AS PROV DED HERE N.
CLA MS BASED ON MPL ED WARRANT ES,
NCLUD NG WARRANT ES OF
MERCHANTAB L TY OR F TNESS FOR A
PART CULAR PURPOSE, ARE L M TED TO
ONE YEAR OR THE SHORTEST PER OD
ALLOWED BY LAW. ELECTROLUX SHALL
NOT BE L ABLE FOR CONSEQUENT AL OR
NC DENTAL DAMAGES SUCH AS
PROPERTY DAMAGE AND NC DENTAL
EXPENSES RESULT NG FROM ANY BREACH
OF TH S WR TTEN L M TED WARRANTY OR
ANY MPL ED WARRANTY. SOME STATES
AND PROV NCES DO NOT ALLOW THE
EXCLUS ON OR L M TAT ON OF NC DENTAL
OR CONSEQUENT AL DAMAGES, OR
L M TAT ONS ON THE DURAT ON OF
MPL ED WARRANT ES, SO THESE
L M TAT ONS OR EXCLUS ONS MAY NOT
APPLY TO YOU. TH S WR TTEN WARRANTY
G VES YOU SPEC F C LEGAL R GHTS. YOU
MAY ALSO HAVE OTHER R GHTS THAT
VARY FROM STATE TO STATE.
This warranty only applies to products
purchased in the USA and CANADA. n
the USA, your appliance is warranted by
Electrolux Home Care Products, nc. n
Canada, your appliance is warranted by
Electrolux Home Care Products Canada nc.
Electrolux authorizes no person to change
or add to any obligations under this warranty.
Product features or specifications as
described or illustrated are subject to
change without notice.
SA
1-800-896-9756
Electrolux Home Care Products, nc.
10200 David Taylor Drive
Charlotte, NC 28262
CANADA
1-800-896-9756
Electrolux Home Care Products Canada nc.
5855 Terry Fox Way
Mississauga, ON, Canada L5V 3E4
www.electrolu .com
airCleanerOG.qxp_AirFilter_English 1/20/14 12:05 PM Page 14