Electrolux ESI 7 Series User manual

ESI 7 Series
UltraSteam™Pro and
UltraSteam™Pro Jeans
Instructions for Use

2
Components
A. UltraSteam™soleplate
B. SafeTouch™hot soleplate safety
indicator
C. Spray nozzle
D. Water lling inlet cover
E. Steam selector (For ESI7304 only)
F. Auto-clean button
G. “No steam” button (For ESI7504 only)
H. Spray button
I. Turbo steam button
J. Temperature indicator light
K. Auto-safety shut o indicator light
L. Temperature selector
M. Maximum water level indicator
N. Water tank
*Due to the Electrolux policy of continual product development; specications, colours and details of our products and those
mentioned in this manual are subject to change without notice.

3
Instruction book
Before using the iron for the rst time,
please read the safety advice.
Safety advice
Before using the iron for the rst time,
read the following instruction carefully
and save for future reference. The
following advice will help you to use
your new iron safely.
• This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience
and knowledge, unless they have
been given supervision or instruction
concerning the use of the appliance by
a person responsible for their safety.
• Children should be supervised to
ensure that they do not play with the
appliance.
• The appliance should only be
connected to a power supply if its
voltage and frequency comply with
the specications written on the rating
plate.
• The iron is not to be used if it has been
dropped, if there are visible signs of
damage to the plug, the main cord, to
the iron itself or if it is leaking.
• The appliance must only be connected
to an earthed socket.
• If the appliance or the supply cord
is damaged, it must be replaced by
the manufacturer, its service agent or
similar qualied person, in order to
avoid hazard.
• The iron must be used and rested on a
stable surface. When placing the iron
on its rubber-napped heel, ensure that
the surface on which the heel is placed
is stable.
• Never leave the appliance unattended
while connected to the supply mains.
• The appliance must be switched o
and the main plug withdrawn each
time after use, before relling, cleaning
and maintenance.
• The plug must be removed from the
socket outlet before the water tank is
lled with water.
• The main cable must not come into
contact with any hot parts of the
appliance.
• Do not immerse the appliance in water
or any other liquid.
• Do not exceed the maximum lling
volume as indicated on the water tank.
• The soleplate of the iron and nearby
surfaces can become extremely hot
and may cause burns if touched. Please
be especially careful when handling
the iron after use, or when re-lling the
water tank during use.
• This appliance is intended for domestic
use only. The manufacturer cannot
accept any liability for possible damage
caused by improper or incorrect use.
Safety Features
1. 3-way auto safety shut o.
If the iron is left unattended, resting
on the soleplate or on the side, it will
automatically turn o after 30 seconds.
If left unattended resting on the heel, it
will turn o after 8 minutes. The auto-
safety shut o indicator light (K) will
start ashing orange and a sound alert
will beep 6 times to indicate that the
iron has been switched o. If you wish
to turn it back on again, move the iron
gently until the temperature indicator
light (J) turns red. It will turn green once
the temperature selected is reached,
meaning the iron is ready to use again.
2. SafeTouchTM hot soleplate safety
indicator
The iron is equipped with a SafeTouchTM
hot soleplate safety indicator (B) located
at the front. The indicator stripe is black
when the iron is cold. As soon as the
soleplate reaches 40oC, the stripe turns
red indicating that the soleplate is hot
and should not be touched. Once the iron
is unplugged, the stripe will slowly revert
to black as the soleplate cools down.
Wait for the stripe to revert to black again
before touching the soleplate or storing
the iron.
Safety
Indicator

4
Getting Started
1. Before rst use.
Remove all adhesive and gently rub
with a dampened cloth before plugging
in the iron.
We recommend that you rinse the
water tank by operating the steam in a
horizontal position away from your linen
for one minute. When the iron is turned
on for the rst time, harmless vapours/
odours may be emitted temporarily.
This will cease quickly.
2. Filling the water tank.
Make sure the iron is unplugged.
Set the temperature selector (L) to
position 0. Open the water lling inlet
cover (D). Using the beaker provided, pour
water up to maximum level. Close the
cover until it clicks.
Caution: Do not exceed the maximum water
level as indicated on the water tank (N).
Type of water to be used: This iron has been
designed to use normal tap water. If the
tap water in your area is very hard, you can
ll the tank with 50% tap water and 50%
bottled distilled water. Never use distilled
water only. Never put scented water,
vinegar or ironing aids in the water tank.
This may cause brown spitting and staining.
3. Plug the power cable into a power
outlets.
Set the temperature selector (L) according
to the fabric type by referring to the
garment label or the ironing chart below.
The temperature indicator light (J) turns
red. When the temperature indicator
light (J) turns green, the iron is ready to
use. The light will switch between red
and green as the iron is maintaining the
selected temperature.
4. Adjust steam and temperature
settings for the model without the
auto-steam function (ESI7304).
Set the temperature selector (L) according
to the fabric type by referring to the
ironing chart. Then adjust the
steam output by setting the steam
selector (E) according to the fabric
type by referring to the ironing chart
below.
For“Dry ironing”, set the steam selector
(E) to the position “o”.
5. Adjust the ironing settings for
the models equipped with the
auto-steam function (ESI7504).
The auto-steam function regulates
the steam amount according to the
temperature set. Set the temperature
selector (L) according to the fabric type
by referring to the ironing chart below,
the steam output will be automatically
adjusted to deliver the most eective
combination for the type of fabric selected.
For“Dry ironing”, press down the“no
steam” button (G). To come back to steam
function, press again the button.
Tips: Setting the right temperature:
Check the laundry care label for the
fabric type. If you select a lower
temperature setting whilst in use, wait
for a few minutes before ironing to make
sure the iron has cooled down. Setting the
right amount of steam: Always make sure
that the steam setting selected is suitable
for the temperature set and fabric type.
The iron is equipped with an anti-drip
device to prevent water from dripping
out of the soleplate when the temperature
selected is too low.
Electrolux
Pia Ringholm
2012-05-10
1:1
SDA, Mahé Iron
AUS
print graphics
Factory: Donlim
191 4994 G
change of knob direction
graphics. /Pia
B 120522
Changed the Ultrasteam
symbol to 600. /Pia
C 121008
Added pos 10, 11 and 12.
/Pia
E 130709
Changed pos 10, 11, 13
/Pia
F 130709
-01
-02 (ESI710B)
-08
-09
-03 (ESI730B) -04 (ESI750B)
-07 (ESI750B)
-05 (ESI710B)
-06 (ESI730B)
-10 (ESI7204B)
-11 (ESI7004R)
-12
-13 (ESI7004R) -14 (ESI7204B)
-15
-16
-17
-18
Electrolux
Pia Ringholm
2012-05-10
1:1
SDA, Mahé Iron
AUS
print graphics
Factory: Donlim
191 4994 G
change of knob direction
graphics. /Pia
B 120522
Changed the Ultrasteam
symbol to 600. /Pia
C 121008
Added pos 10, 11 and 12.
/Pia
E 130709
Changed pos 10, 11, 13
/Pia
F 130709
-01
-02 (ESI710B)
-08
-09
-03 (ESI730B) -04 (ESI750B)
-07 (ESI750B)
-05 (ESI710B)
-06 (ESI730B)
-10 (ESI7204B)
-11 (ESI7004R)
-12
-13 (ESI7004R) -14 (ESI7204B)
-15
-16
-17
-18

5
6. Using the Spray mist to remove
stubborn creases.
Ensure the water tank is at least 1/4 full.
Use the spray mist to pre-dampen fabrics
by pressing the spray button (H) several
times to release a fine mist.
7. Turbo steam function.
Make sure the temperature selector (L) is set
on ••• or higher. To release a Turbo shot
of steam, press the Turbo steam button
(I) 1 or 2 times. Always wait for a few
seconds after each shot before pressing
the button again.
8. Vertical steaming.
Vertical steam function is ideal for
steaming curtains, suits, dresses and
delicate fabrics. Hang item on a hanger
(always use a hanger, never use on a
garment while someone is wearing it),
hold the iron at a distance of 10 cm, set the
iron on ••• or higher and press the Turbo
steam button (I) 1 or 2 times. Always wait
for a few seconds after each shot before
pressing the button again. Never direct
steam at someone.
Using the iron
Ironing chart
Fabric Temperature setting Steam setting
(For ESI7304)
Ironing recommendation
Acrylic •o Dry iron on reverse side.
Acetate •o Dry iron on reverse side while still damp or use
spray to dampen.
Nylon, Polyamide & Polyester •o Dry iron on reverse side while still damp or use
spray to dampen.
Rayon •o Dry iron on reverse side of fabric.
Viscose •o Dry iron using a dampen ironing cloth to
prevent shine marks.
Silk •o or Dry iron using a dampen ironing cloth to
prevent shine marks.
Wool & wool blends •• Steam iron on reverse side or use ironing cloth.
Cotton blends •• Check garment label and follow manufacturer’s
instructions. Use setting for the bre requiring
lowest setting.
Cotton ••• Dry iron on reverse side.
Corduroy ••• Steam iron on reverse side or use ironing cloth.
Linen ••• to “max” Steam iron on reverse side or use ironing cloth
to prevent shine marks, especially with dark
colours.
Denim ••• to “max” (For ESI7304)
JEANS (For ESI7504)
Use turbo steam function if needed.
For model ESI7504, the auto-steam system adjusts automatically the steam output and ensures you always get the ideal amount of
steam according to the temperature selected.
Please note: When set on the • program, the iron will not produce steam. The iron heats up faster than it cools down.

6
Cleaning and Care
4. Auto-clean function.
The auto-clean function helps to slow
down scaling and build up in the iron. It is
recommended to perform the auto-clean
function every 4 weeks.
Cleaning (do not use any detergent)
1. Unplug the iron before cleaning.
Always place the iron on its heel rest and
allow cooling down.To clean exterior
surfaces, use a damp soft cloth and wipe
dry.Do not use any chemical solvents, as
these will damage the surface.
2. Cleaning the soleplate.
Do not use scouring pads or harsh
cleaners on the soleplate as these may
damage the surface.To remove burnt
residue, iron over a damp cloth while
the iron is still hot.To clean the soleplate,
simply wipe with a soft damp cloth and
wipe dry.
3. Permanent anti-scale cartridge
The permanent anti-scale cartridge
prevents scale from building up into the
soleplate and will help to extend the
life of the iron if the auto-clean function
is performed regularly.This system is
permanent and does not need to be
replaced.
Auto-clean function for model without
auto-steam function (ESI7304).
Fill the water tank up to 100ml with cold
tap water. Place the iron on its heel rest.
Plug the iron and set the temperature
selector (L) to the MAX position. When
the temperature indicator light (J) turns
green, unplug the iron, and hold it over
a sink, then turn the steam selector (E)
to the auto-clean position and pull out
the button (F). Gently shake over the sink
until all the water is gone. Insert the auto-
clean button (F) back and press until it
clicks. Turn the iron on the MAX setting to
dry the soleplate. Once the temperature
indicator light (J) turns green again,
unplug the iron, let it cool down on its
heel rest and wipe the soleplate with a
dry cloth.
Auto-clean function for model with
auto-steam function (ESI7504).
Fill the water tank up to 100ml with cold
tap water. Place the iron on its heel rest.
Plug the iron and set the temperature
selector (L) to the MAX/autoclean
position. When the temperature indicator
light (J) turns green, unplug the iron,
and hold it over a sink, then pull out
the auto-clean button (F). Gently shake
over the sink until all the water is gone.
Insert the auto-clean button (F) back
and press until it clicks. Turn the iron on
the MAX setting to dry the soleplate.
Once the temperature indicator light (J)
turns green again, unplug the iron, let it
cool down on its heel rest and wipe the
soleplate with a dry cloth.
• Attention, if the temperature selector
(L) is not on MAX/auto clean position, it
will not be possible to pull out or place
back the auto-clean button (F).

7
Troubleshooting
Problem Possible cause Solution
The soleplate is not
heating even though the
iron is plugged in
There is a connection problem. Check the main power supply cable, the plug and the
wall outlet.
The temperature selector (L) is in • position. Select the adequate temperature - see “Ironing Chart”.
The iron has been left unattended for some
time and the 3-way auto safety shut o
function has switched the iron o.
To turn the iron back on, gently move the iron until
the temperature indicator light (J) turns on red or if
you have nished ironing, unplug and store the iron.
The iron does not produce
steam
There is not enough water in the tank. Fill the water tank - see “Getting started”.
The “No steam”button (G) is set to “o”
position (for model ESI7504).
Set the “No steam” button (G) to the “On”position.
The steam selector (E) is set to“o” position. Set the steam selector between minimum steam and
maximum steam - See “Ironing Chart”.
The iron is not hot enough and the anti-drip
device has been automatically activated.
Set the temperature selector (L) to a position between
••• and MAX. Place the iron on its heel rest and wait
until the temperature indicator light (J) turns on
green.
There is a build up of scale in the soleplate. Carry out the auto-clean function - see “Cleaning and
C a r e ”.
The spray function does
not work
There is not enough water in tank. Fill the water tank - see “Getting started”
The turbo steam function
does not work
The turbo steam function was used too
frequently within a short period of time.
Continue ironing on horizontal position for a while
and wait before using the turbo steam or vertical
steam functions again.
The iron is not hot enough. Adjust the temperature selector (L) to •••. Put the iron
in vertical position and wait until the temperature
indicator light (J) turns on green.
Flakes and impurities
come out of the soleplate
during ironing.
You have used hard water or pure distilled
water, which has caused scale akes to
develop in the water tank.
Perform the auto-clean function - see “Cleaning and
C a r e ”.
The iron spits and stains
the linen
You are using either pure bottled distilled
water, vinegar, scented, starch or chemical
descaling agents.
Always use normal tap water with no additives- See
“Getting Started”. Perform the auto-clean function -
see “Cleaning and Care”.
You are ironing new garments before washing
them or linen which has not been rinsed
suciently.
Always clean new garments before ironing and make
sure linen is rinsed suciently.
Perform the auto-clean function - see “Cleaning and
Care”
The soleplate is brown
and may stain the linen
You have set the temperature selector (L) on a
too hot position.
Check the laundry care label of the garments and
select the adequate temperature - see“Ironing Chart”.
Clean the soleplate using a damp cloth while the iron
is still warm. Do not use chemicals or scouring pads.

8
Electrolux Home Products Pty Ltd
ABN 51 004 762 341
163 O’Riordan Street, Mascot, NSW 2020, Australia
Customer Service Phone: [phone]
www.electrolux.com
Electrolux Small Appliances
A division of Electrolux (NZ) Limited
3 - 5 Niall Burgess Road, Mt. Wellington, Auckland, New Zealand
Phone: [phone] - Customer Service Phone: [phone]
www.electrolux.com
*Due to the Electrolux policy of continual product development; specications, colours and details of our products and those
mentioned in this manual are subject to change without notice.
APAC-ESI7304_7504-IFU-AU-1