Electrolux CI6-80 User manual

Installation manual
Cold Ironer
CI6-80
Original instructions
427001235/EN
2020.09.28

Contents
Contents
1 Safety Precautions...............................................................................5
1.1 General safety information ........................................................... 5
1.2 Symbols...................................................................................6
2 Technical data.....................................................................................7
3 Attachment.........................................................................................8
4 Electrical connection ............................................................................9
4.1 Alternative electrical connection ....................................................9
5 Function check.................................................................................. 10
6 Disposal information........................................................................... 11
6.1 Disposal of appliance at end of life ............................................... 11
6.2 Disposal of packing................................................................... 11
The manufacturer reserves the right to make changes to design and component
specifications.

Installation manual 5
1 Safety Precautions
This appliance can be used in public areas.
Remove all objects from pockets such as lighters and matches.
WARNING. This appliance is intended only for drying textiles
washed in water.
DO NOT MODIFY THIS APPLIANCE.
Servicing shall be carried out only by authorized personnel.
Only authorized spare parts shall be used.
When performing service or replacing parts, the power must be
disconnected.
A-weighted emission sound pressure level at workstations: <70
dB
Additional requirements for the following countries: AT, BE, BG,
HR, CY, CZ, DK, EE, FI, FR, DE, GR, HU, IS, IE, IT, LV, LT, LU,
MT, NL, NO, PL, PT, RO, SK, SI, ES, SE, CH, TR, UK:
• This appliance can be used in public areas.
• This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
Additional requirements for other countries:
• This appliance is not intended for use by persons (including children) with reduced physi-
cal, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety. Children should be supervised to ensure that they do not play
with the appliance.
1.1 General safety information
Do not hose down the machine with water.
In order to prevent damage to the electronics (and other parts) that may occur as the result
of condensation, the machine should be placed in room temperature for 24 hours before
being used for the first time.

6Installation manual
1.2 Symbols
Caution
Caution, hot surface
Read the instructions before using the machine.
Be careful. The ironer is top heavy and can tip over
easily.

Installation manual 7
2 Technical data
6
3
2
1
5
A
D
C
BF
E
4
fig.W01417
A B C D E F
mm 970 855 1060 570 860 830
1 Switch
2 Control gate
3 Folding work table
4 Collection bin
5 Feet
6 Anti-tip protection
Cylinder diameter: ⌀mm 130
Cylinder length: mm 740
Cylinder speed: rpm: 14
Cylinder pressure: kg 300
Net weight: kg 120

8Installation manual
3 Attachment
Do not use the ironer unless it is screwed to the wall
fig.W01418
The ironer comes with 2 brackets and 2 screws for securing the brackets to the
ironer.
• Position the ironer in the intended location.
• Drill mounting holes in the wall for the fastening screws through the mounting bracket.
• The ironer must be anchored to the wall via the brackets with fasteners equivalent to a 5
x 30 wood screw.

Installation manual 9
4 Electrical connection
The electrical installation may only be performed by qualified personnel.
The ironer is delivered ready for connection, with cable and grounded plug.
A grounded electrical outlet must be found within 2 m of the right side of the ironer. The iron-
er has a 2 m grounded cable with plug connected at the bottom right-hand side. If the elec-
trical outlet is not found within the reach described above, then the appliance's position
must be adjusted. Do not use an extension cord.
We recommend that the mains cable be equipped with a ground fault interrupter.
Mains voltage Hz Total output
kW
Recommended fuse
A
220 - 230V 1~ 50 0.37 10
fig.W01419
4.1 Alternative electrical connection
The ironer can also be permanently connected. In such case, it must be connected via an
all-pole switch installed in the immediate vicinity of the ironer.
The grounded electrical outlet or all-pole switch must be within easy reach of the ironer after
it has been installed.

10 Installation manual
5 Function check
May only be performed by qualified personnel.
A function check must be performed when the installation is finished and before the appli-
ance can be used.
Whenever a repair has been made, a function check must be performed before the appli-
ance can be used again.
Ready for use
If all tests are OK the appliance is now ready for use.
If any of the tests fail, or deficiencies or faults are detected, please contact your local serv-
ice organization or supplier.

Installation manual 11
6 Disposal information
6.1 Disposal of appliance at end of life
Before disposing of the machine, make sure to carefully check its physical condition, and in
particular any parts of the structure that can give or break during scrapping.
The machine’s parts must be disposed of in a differentiated way, according to their different
characteristics (e.g. metals, oils, greases, plastic, rubber, etc.).
Different regulations are in force in the various countries, therefore comply with the provi-
sions of the laws and competent bodies in the country where scrapping takes place.
In general, the appliance must be taken to a specialised collection/scrapping centre.
Dismantle the appliance, grouping the components according to their chemical characteris-
tics, remembering that the compressor contains lubricant oil and refrigerant fluid which can
be recycled, and that the refrigerator and heat pump components are special waste assimil-
able with urban waste.
The symbol on the product indicates that this product should not be treated as domestic waste, but
must be correctly disposed of in order to prevent any negative consequences for the environment and
human health. For further information on the recycling of this product, contact the local dealer or agent,
the Customer Care service or the local body responsible for waste disposal.
Note!
When scrapping the machine, any marking, this manual and other documents con-
cerning the appliance must be destroyed.
6.2 Disposal of packing
The packing must be disposed of in compliance with the current regulations in the country
where the appliance is used. All the packing materials are environmentally friendly.
They can be safely kept, recycled or burned in an appropriate waste incineration plant. Re-
cyclable plastic parts are marked as following examples.
PE
Polyethylene:
• Outer wrapping
• Instructions bag
PP
Polypropylene:
• Straps
PS
Polystyrene foam:
• Corner protectors

Electrolux Professional AB
341 80 Ljungby, Sweden
www.electroluxprofessional.com