Electrolux EFA9620 User manual

USER MANUAL
EFA9620

electrolux 3
RECOMMENDATIONS AND SUGGE-
STIONS 6
CHARACTERISTICS 7
USE 12
MAINTENANCE 14
EN
IT

4 electrolux
Welcome to the world of Electrolux
Thank you for choosing a first class
product from Electrolux, which hopeful-
ly will provide you with lots of pleasure
in the future. The Electrolux ambition is
to offer a wide variety of quality prod-
ucts that make your life more comfort-
able. You find some examples on the
cover in this manual. Please take a few
minutes to study this manual so that
you can take advantage of the benefits
of your new machine. We promise that
it will provide a superior User Experi-
ence delivering Ease-of-Mind.
Good luck!
EN

electrolux 5

6 electrolux Recommendations and Suggestions
EN
Installation
• The manufacturer will not be held li-
able for any damages resulting from
incorrect or improper installation.
• The minimum safety distance be-
tween the cooker top and the extrac-
tor hood is 650 mm.
• Check that the mains voltage corre-
sponds to that indicated on the rating
plate fixed to the inside of the hood.
• For Class I appliances, check that the
domestic power supply guarantees
adequate earthing.
Connect the extractor to the exhaust
flue through a pipe of minimum diam-
eter 120 mm. The route of the flue
must be as short as possible.
• Do not connect the extractor hood to
exhaust ducts carrying combustion
fumes (boilers, fireplaces, etc.).
• If the extractor is used in conjunction
with non-electrical appliances (e.g.
gas burning appliances), a sufficient
degree of aeration must be guaran-
teed in the room in order to prevent
the backflow of exhaust gas. The
kitchen must have an opening com-
municating directly with the open air in
order to guarantee the entry of clean
air.
Use
• The extractor hood has been de-
signed exclusively for domestic use to
eliminate kitchen smells.
• Never use the hood for purposes
other than for which it has ben de-
signed.
• Never leave high naked flames under
the hood when it is in operation.
• Adjust the flame intensity to direct it
onto the bottom of the pan only, mak-
ing sure that it does not engulf the
sides.
• Deep fat fryers must be continuously
monitored during use: overheated oil
can burst into flames.
• Do not flambè under the range hood;
risk of fire
• The hood should not be used by chil-
dren or persons not instructed in its
correct use.
Maintenance
• Switch off or unplug the appliance
from the mains supply before carrying
out any maintenance work.
• Clean and/or replace the Filters after
the specified time period.
• Clean the hood using a damp cloth
and a neutral liquid detergent.
The symbol on the product or on its
packaging indicates that this product may
not be treated as household waste. Instead
it shall be handed over to the applicable
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for
the environment and human health, which
could otherwise be caused by inappropriate
waste handling of this product. For more
detailed information about recycling of this
product, please contact your local city office,
your household waste disposal service or
the shop where you purchased the product.
RECOMMENDATIONS AND SUGGESTIONS

Characteristics electrolux 7
EN
Dimensions
CHARACTERISTICS

8 electrolux Characteristics
EN
Components
Ref. Q.ty Product Components
11 Hood Body, complete with: Con-
trols, Light, Blower, Filters
21 Telescopic Chimney comprising:
2.1 1 Upper Section
2.2 1 Lower Section
7.1 1 Telescopic frame complete with
extractor, consisting of:
7.1a 1 Upper frame
7.1b 1 Lower frame
91 Reducer Flange ø 150-120 mm
10 1 Flange ø 150
15 1 Air Outlet Connection
24 1 Junction box
25 2 Pipe clamps
Ref. Q.ty Installation Components
11 4 Wall Plugs ø 10
12c 6 Screws 2,9 x 6,5
12e 2 Screws 2,9 x 9,5
12f 4 Screws M6 x 10
12g 4 Screws M6 x 80
12h 4 Screws 5,2 x 70
21 1 Drilling template
22 4 6.4 mm int. dia washers
23 4 M6 nuts
Q.ty Documentation
1 Instruction Manual
12c
7.1a
7.1
22
23
12h
7.1b
2
2.1
2.2
12c
11
21
12g
24
12e
15
12c
25
9
10
12f
1

Installation electrolux 9
EN
INSTALLATION
Drilling the Ceiling/shelf
• Use a plumb line to mark the centre of
the hob on the ceiling/support shelf.
• Place the drilling template 21 provided
on the ceiling/support shelf, making
sure that the template is in the correct
position by lining up the axes of the
template with those of the hob.
• Mark the centres of the holes in the
template.
• Drill the holes at the points marked:
• for concrete ceilings, drill for plugs
appropriate to the screw size.
• for hollow brick ceilings with wall
thickness of 20 mm: drill ø 10
mm(immediately insert the Dowels
11 supplied).
• for wooden beam ceilings, drill ac-
cording to the wood screws used.
• for wooden shelf, drill ø 7 mm.
• for the power supply cable feed, drill
ø 10 mm.
• for the air outlet (Ducted Version),
drill according to the diameter of the
external air exhaust duct connec-
tion.
• Insert two screws of the following
type, crossing them and leaving 4-5
mm from the ceiling:
• for concrete ceilings, use the appro-
priate plugs for the screw size (not
provided).
• for Cavity ceiling with inner space,
with wall thickness of approx. 20
mm, Screws 12h, supplied.
• for wooden beam ceilings, use 4
wood screws (not provided).
• for wooden shelf, use 4 screws 12g
with washers 22 and nuts 23, pro-
vided.

10 electrolux Installation
EN
Fixing the frame
• Loosen the two screws fastening the
lower chimney and remove this from
the lower frame.
• Loosen the two screws fastening the
upper chimney and remove this from
the upper frame.
If you wish to adjust the height of the
frame, proceed as follows:
• Unfasten the eight metric screws join-
ing the two columns, located at the
sides of the frame.
• Adjust the frame to the height re-
quired, then replace all the screws
removed as above.
• Insert the upper chimney stack from
above, and leave it running free on the
frame.
• Lift up the frame, fit the frame slots
onto the screws up to the slot end
positions.
• Tighten the two screws and fasten
the other two screws provided with
the hood.
Before tightening the screws completely
it is possible to adjust the frame by tur-
ning it. Make sure that the screws do
not come out of their seats in the slotted
holes.
• The frame mountings must be secure
to withstand the weight of the hood
and any stresses caused by the oc-
casional side thrust applied to the
device.
On completion, check that the base is
stable, even if the frame is subjected
to bending.
• In all cases where the ceiling is not
strong enough at the suspension
point, the installer must provide
strengthening using suitable plates
and backing pieces anchored to the
structurally sound parts.
22
11