Electrolux EFC 9500 User manual

Instruction Manual
EFC 9500EFC 9500
EFC 9500EFC 9500
EFC 9500
GB

3GB
CONTENTS
Dear Customer,
If you follow the recommendations
contained in this Instruction Manual,
your appliance will give you constant
high performance and will remain
efficient for many years to come.
RECOMMENDATIONS AND SUGGESTIONS 4
CHARACTERISTICS 5
INSTALLATION 7
USE 9
MAINTENANCE 10

4GB
RECOMMENDATIONS AND SUGGESTIONS
INSTALLATION
• The manufacturer will not be held liable for any damages resulting
from incorrect or improper installation.
• The minimum safety distance between the cooker top and the
extractor hood is 650 mm.
• Check that the mains voltage corresponds to that indicated on the
rating plate fixed to the inside of the hood.
• For Class I appliances, check that the domestic power supply
guarantees adequate earthing.
Connect the extractor to the exhaust flue through a pipe of
minimum diameter 120 mm. The route of the flue must be as short
as possible.
• Do not connect the extractor hood to exhaust ducts carrying
combustion fumes (boilers, fireplaces, etc.).
• Iftheextractorisusedinconjunctionwithnon-electricalappliances
(e.g. gas burning appliances), a sufficient degree of aeration must
be guaranteed in the room in order to prevent the backflow of
exhaust gas. The kitchen must have an opening communicating
directly with the open air in order to guarantee the entry of clean
air.
USE
• The extractor hood has been designed exclusively for domestic
use to eliminate kitchen smells.
• Never use the hood for purposes other than for which it has ben
designed.
• Never leave high naked flames under the hood when it is in
operation.
• Adjust the flame intensity to direct it onto the bottom of the pan
only, making sure that it does not engulf the sides.
• Deep fat fryers must be continuously monitored during use:
overheated oil can burst into flames.
• The hood should not be used by children or persons not instructed
in its correct use.
MAINTENANCE
• Switch off or unplug the appliance from the mains supply before
carrying out any maintenance work.
• Clean and/or replace the Filters after the specified time period.
• Clean the hood using a damp cloth and a neutral liquid detergent.
650 mm min.

5GB
CHARACTERISTICS
Dimensions
650 min.
520
420
48
6
L
530
108
252
150
740
870
1200
290
350
63
4181
126

6GB
Components
Ref. Q.ty Product Components
11 Hood Body, complete with: Controls, Light,
Blower, Filters
21 Telescopic Chimney comprising:
2.1 1 Upper Section
2.2 1 Lower Section
91 ReducerFlangeø 150-120 mm
14.1 2 Air Outlet Connection Extension
15 1 AirOutletConnection
Ref. Q.ty Installation Components
7.2.1 2 Upper Chimney Section Fixing Brackets
7.3 1 Air Outlet Connection Support
11 6 Wall Plugs
12a 6 Screws 4,2 x 44,4
12c 6 Screws 2,9 x 9,5
Q.ty Documentation
1 Instruction Manual
1 Warranty
2.1
2.2
2
12c
12a 7.2.1 11
11
12a
1
9
7.3
14.1
15

7GB
INSTALLATION
Wall drilling and bracket fixing
Wall marking:
• Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the centre
of the area in which the hood will be installed.
• Draw a horizontal line at 650 mm above the hob.
• Place bracket 7.2.17.2.1
7.2.17.2.1
7.2.1 on the wall as shown about 1-2 mm from the ceiling or upper limit aligning
the centre (notch) with the vertical reference line.
• Mark the wall at the centres of the holes in the bracket.
• Place bracket 7.2.17.2.1
7.2.17.2.1
7.2.1 on the wall as shown at X mm below the first bracket (X = height of the upper
chimney section supplied), aligning the centre (notch) with the vertical line.
• Mark the wall at the centres of the holes in the bracket.
• Mark a reference point as indicated at 116 mm from the vertical reference line and 306 mm above
the horizontal reference line.
• Repeat this operation on the other side.
• Drill ø 8 mm holes at all the centre points marked.
• Insert the wall plugs 1111
1111
11 in the holes.
• Fix the lower bracket 7.2.17.2.1
7.2.17.2.1
7.2.1 using the 12a12a
12a12a
12a screws (4,2 x 44,4) supplied.
• Fix the upper bracket 7.2.17.2.1
7.2.17.2.1
7.2.1 and the air outlet connection support 7.37.3
7.37.3
7.3 together using the 2 screws
12a12a
12a12a
12a (4,2 x 44,4) supplied.
• Insert the two screws 12a12a
12a12a
12a (4,2 x 44,4) supplied in the hood body fixing holes, leaving a gap of 5-
6 mm between the wall and the head of the screw.
11
12a
306 X
116
1÷2
116
650 min.
7.2.1

8GB
Mounting the hood body
• Before attaching the hood body, tighten the two
screws VrVr
VrVr
Vr located on the hood body mounting
points.
• Hook the hood body onto the screws 12a12a
12a12a
12a
• Fully tighten support screws 12a12a
12a12a
12a
• Adjust screws VrVr
VrVr
Vr to level the hood body.
Connections
DUCTED VERSION AIR EXHAUST SYSTEM
When installing the ducted version, connect the hood to the chimney using either a flexible or rigid
pipe ø 150 or 120 mm, the choice of which is left to the installer.
• To install a ø 120 mm air exhaust connection,
insert the reducer flange 99
99
9 on the hood body
outlet.
• Fix the pipe in position using sufficient pipe
clamps (not supplied).
• Remove any activated charcoal filters.
RECIRCULATION VERSION AIR OUTLET
• Put connection 1515
1515
15 into the connection support 7.3.7.3.
7.3.7.3.
7.3.
• Insert the connection extension pieces laterally 14.114.1
14.114.1
14.1
in connection 15.15.
15.15.
15.
• Make sure that the outlet of the extension pieces 14.114.1
14.114.1
14.1
ishorizontallyandverticallyalignedwiththechimney
outlets.
• Connect the air outlet connection 1515
1515
15 to the hood body
outlet using either a flexible or rigid pipe ø 150 or
120 mm, the choice of which is left to the installer.
• Ensure that the activated charcoal filters have been
inserted.
ELECTRICAL CONNECTION
• Connect the hood to the mains through a two-
pole switch having a contact gap of at least 3
mm.
• Remove the grease filters (see paragraph
Maintenance) being sure that the connector of
the feeding cable is correctly inserted in the
socket placed on the side of the fan.
12a
Vr
9
ø 120ø 150
ø 150
14.1
15

9GB
L
V1 V2 V3
S
Flue assembly
Upper exhaust flueUpper exhaust flue
Upper exhaust flueUpper exhaust flue
Upper exhaust flue
• Slightly widen the two sides of the upper flue
and hook them behind the brackets 7.2.17.2.1
7.2.17.2.1
7.2.1,
making sure that they are well seated.
• Secure the sides to the brackets using the 4
screws 12c12c
12c12c
12c (2,9 x 9,5) supplied.
• Makesurethattheoutlet of the extensions pieces
is aligned with the chimney outlets.
Lower exhaust flueLower exhaust flue
Lower exhaust flueLower exhaust flue
Lower exhaust flue
• Slightlywidenthetwo sides of the flue and hook
them between the upper flue and the wall,
making sure that they are well seated.
• Fix the lower part laterally to the hood body
using the 2 screws 12c12c
12c12c
12c (2,9 x 9,5) supplied.
12c
2.1
2.2
2
7.2.1
12c
USE
Control panel
LL
LL
L Light Switches the lighting system on and off.
SS
SS
S Led Motor running led.
V1V1
V1V1
V1 Motor Switches the extractor motor on and off at low speed. Used to provide a contin-
uos and silent air change in the presence of light cooking vapours.
V2V2
V2V2
V2 Speed Medium speed, suitable for most operating conditions given the optimum treated
air flox/noise level ratio.
V3V3
V3V3
V3 Intensive Maximum speed, used for eliminating the highest cooking vapour emission,
including long periods.

10GB
MAINTENANCE
Grease filters
CLEANING METAL SELF- SUPPORTING GREASE FILTERS
• The filters must be cleaned every 2 months
of operation, or more frequently for
particularly heavy usage, and can be
washed in a dishwasher.
• Remove the filters one at a time by pushing
them towards the back of the group and
pulling down at the same time.
• Wash the filters, taking care not to bend
them. Allow them to dry before refitting.
• When refitting the filters, make sure that
the handle is visible on the outside.
Activated charcoal filter (Recirculation version)
REPLACING THE ACTIVATED CHARCOAL FILTER
• The filter is not washable and cannot be
regenerated, and must be replaced
approximately every 4 months of operation, or
more frequently for particularly heavy usage.
• Remove the metal grease filters
• Remove the saturated activated carbon filter by
releasing the fixing hooks
• Fit the new filter by hooking it into its seating
• Replace the metal grease filters.
Lighting
LIGHT REPLACEMENT
20 W halogen light.20 W halogen light.
20 W halogen light.20 W halogen light.
20 W halogen light.
• Remove the snap-on lamp cover by levering it
from under the metal ring, supporting it with
one hand.
• Extract the Lamp from the Support.
• Replace with another of the same type, making
sure that the two pins are properly inserted in
the lamp holder socket holes.
• Replace the snap-on lamp cover.