Elektra Beckum 091 001 8442 User manual

115 161 1687 / 1001 - 5.0
091 001 8442
Tischverbreiterung . . . . . . . . . . . . . . . . . . .3
Table Extension . . . . . . . . . . . . . . . . . . . . . .5
Rallonge latérale de table . . . . . . . . . . . . . .7
Tafelverbreding . . . . . . . . . . . . . . . . . . . . . .9
Allargamento del tavolo . . . . . . . . . . . . . . .11
Extensión de la mesa . . . . . . . . . . . . . . . .13
Alargador da bancada . . . . . . . . . . . . . . . .15
Bordforbredelse . . . . . . . . . . . . . . . . . . . . .17
Bordforlengelse . . . . . . . . . . . . . . . . . . . . .19
Tillsatsbord - bredd . . . . . . . . . . . . . . . . . .21
Pöydän levennys . . . . . . . . . . . . . . . . . . . .23
Asztalszélesítő . . . . . . . . . . . . . . . . . . . . . .25
Poszerzenie stołu. . . . . . . . . . . . . . . . . . . .27
Πεπλτυνση του πγκου . . . . . . . . . . . .29
U1A0168.fm
424344454647484950515253
41

5
ENGLISH
•Read these instructions before use.
Also observe the instructions for the
circular saw, the safety instructions
in particular.
3Note:
This table side extension is
intended for laterally extending the sup-
port area of the circular saw table (1). In
order to be able to install the table side
extension, the Base System Rails (2) fit-
ting the saw must be installed.
The table side extension can be fitted
either to the left (4) or right (3) hand side
of the saw table. The scale supplied are
intended for installation on the right hand
side, as the sliding carriage can be
intalled on the left hand side.
1. Slide pointer (5) under the two
screws (6) as illustrated and tighten
both screws.
2. Put both clamping plate (7) and coil
spring (8) on the carriage bolt (9) as
ilustrated: The offset ends of the
clamping plate must point towards
the carriage bolt's head.
3. Insert carriage bolt (with fitted
clamping plate and coil spring) from
the outside into the hole of the side
extension's mounting rail.
4. Put distance sleeve (10) from inside
on the carriage bolt and screw on
knurled thumb nut (11), but do not
yet tighten it.
5. Repeat steps 2. though 4. on the
other end of the table side exten-
sion.
6. Slide table side extension into the
two extrusions (12) of the base sys-
tem rails: The table side extension
must be pushed at both ends fully
against the saw table.
7. Tighten knurled thumb nuts (11).
ACaution!
The table side extension must
be exactly level with the saw table,
otherwise workpiece and rip fence
may get caught by the step or rock.
If the table side extension is too low:
Loosen screws (13) on the underside
and slide one or more shim plates (14)
below the table extension's mounting
rails. Tighten screws (13).
Scale alignment
1. Position rip fence (15) at the approx-
imate centre of the table side exten-
sion and lock with ratchet lock lever
(16).
2. Make trial cut: Place workpiece
against rip fence and make a cut.
3. Measure the width of the workpiece
(from edge of cut to rip fence).
4. Loosen fixing screw (17) of the table
side extension's scale.
1. Please Read First!
2. Mounting Locations
3. Assembly
1
2
34
56
78
9
10 11
12
39
ELEKTRA BECK
U
42 43 44 45 46 47 48 49 50 51 52 53
41
39
13 14
ELEKTRA BECKUM
23 24 25 26 27 28 29 30 31 32 33 34
22
20
KTRA BECKUM
ELEKTRA BECKUM
4
15
16
17
XA0028E1.fm Operating Instruction ENGLISH

6
ENGLISH
5. Move scale, until the value indicated
by the left-hand edge of the rip
fence corresponds with the value
measured at the workpiece.
6. Tighten scale fixing screw (17)
again.
7. Set rip fence exactly to 320 mm (for
UK 220 and PK 200) or 520 mm (for
PKF 255) and lock it in position.
8. Loosen scale fixing screw (18) of the
base system rail.
9. Move the base system rail's scale
(19), until the value indicated by the
table extension's pointer (20) corre-
sponds exactly with the rip fence
distance (320 mm or 520 mm
respectively).
10. Tighten scale fixing screw (18)
again.
ARisk of Kickback!
The rip fence's fence extru-
sion must always be exactly parallel
with the saw blade. Otherwise there is
a risk of the workpiece jamming bet-
ween saw blade and rip fence, cau-
sing it to be kicked back against the
operator.
1. Set rip fence exactly to 320 mm (for
UK 220 and PK 200) or 520 mm (for
PKF 255) and lock it in position.
2. Loosen knurled nuts on underside of
the table side extension and set
table extension (with the rip fence)
to desired width. The cutting width is
indicated by the base system rail's
scale.
3. Tighten knurled nuts on underside
of table extension again.
4. Place workpiece against rip fence
and perform the cut.
4. Operation
75 76
74
73
72
71
44
43
42
41
40
39
38
45 46 47 48 49 50 51 52
ELEKTRA BECKUM
3
4
75 76
74
73
72
71
18
44
43
42
41
40
39
38
35
34
33
32 45 4
6
37
36
23 24 25 26 27 28 29 30 31 32 33 34
22
20
19
20
A
B
A = B