ELEKTROBOCK WS301 User manual
UNDER THE SWITCH
WS301WS301
MADE IN CZECH REPUBLIC
WIRELESS
RECEIVER
for wireless control of various electric devices
RANGE
UP TO
150 M
- to control all transmitters series WS3xx can
be used
- small dimensions allow mounting directly into
the installation box
- for heaters, circulation pumps, lighting, air
conditioning and other equipment up to 16 A
ws301_en:Layout 1 18.2.2013 18:18 Page 1
INSTALLATION
Wiring diagram:
230 V/ 50 Hz
L
N
max.
16 A
LN
FUNCTION BUTTON ( R ) :
SHORT PRESSING (for about 1.5s)
- coding.
LONG PRESSING (for about 5s)
- RESET deleting the code from the
memory (the LED1 and LED2
flash simultaneously).
WS301 is suitable for switching on electric equipment. Transmitters, se-
ries WS3xx, can be used as a remote control (WS310-stick, WS320-
door contact transmitter, the current channel list on www.elbock.cz).
To be installed in internal rooms. Do not locate near power lines! The device
can only be installed by a person with adequate qualification!
The installation must be executed in a voltage-free state!
1. Switch off the main circuit breaker and connect it to the receiver according
to the diagram;
2. Switch on the main circuit breaker; the LED1 lits up on the receiver; BASIC MODE;
3. Pressing the FUNCTION BUTTON for about 5 sec, will erase the memory
(LED1 and LED2 simultaneous long flash), RESET MODE;
4. Pressing the FUNCTION BUTTON for about 1.5 sec, will get the receiver
into a setting mode for SWITCH ON (LED2 flashing);
5. Press the appropriate button, based on a transmmitter, for transmitting of
a code for SWITCH ON, LED1 flashing and receiver waits for SWITCH OFF.
6. In next step press the same button (or another), on the transmitter, for
transmitting of code for SWITCH OFF;
WS301
7. For setting COUNTING MODE proceed in a similar way;
(!When setting other functions do not use RESET - otherwise, the previ-
ous settings will be erased, it is possible to set up to 16 control buttons!)
8. Pressing the FUNCTION BUTTON for about 1.5 sec, will get the receiver
into a setting mode for SWITCH ON (LED2 flashing);;
9. Press the appropriate button, based on a transmmitter, for transmitting of
a code for SWITCH ON, LED1 flashing and receiver waits for SWITCH OFF.
10. Wait for 20sec, then the receiver is on SETTING TIME MODE (LED1 flashing
and LED2 lit); (!Setting range of time is 1s to 8 hours!)
11. Start to count down of the time,for which the device should be switched on. After the
expiry of the time you have requested press the transmitter button to SWITCH OFF.
ws301_en:Layout 1 18.2.2013 18:18 Page 2
EXPLANATION: LIT UNLIT FLASHING
LED2 FUNCTIONS OF WS301 - indication on receiver
1, power on 230V/ 50Hz
2, device is off
receiver waits for SWITCH ON code, if the code is not re-
ceived during 20 sec., receiver goes back to BASIC MODE
receiver waits for SWITCH OFF code, if the code is not received
during 20 sec. receiver goes back to SETTING TIME MODE
device is on
From the beginning of the time count down, receiver waits for SWITCH
OFF code, receiver goes back to BASIC MODE after receiving the code.
device is on and counts down the time (after a set time
automatically turns off and goes into BASIC MODE.
BASIC MODE
SWITCH ON MODE
SWITCH OFF MODE
RELAY SWITCHED
TIME SETTING MODE
COUNT DOWN MODE
flashing simultaneously (5x) - code was erased, is
necessary to set receiver again RESET MODE
LED1
flashing alternaltely - indicates that the transmitter, which
controls the reciever, has exhausted batteries! LOW BATTERY
(in the transmitter)
ws301_en:Layout 1 18.2.2013 18:18 Page 3
CERTIFICATE OF GUARANTEE
(guarantee period for the product amounts to 2 years)
product No.: date of sale:
stamp of shop:
examined by:
In case of guarantee or
post-guarantee service is
needed, send the receiver to
the distributor or
manufacturer’s address.
DECLARATION OF CONFORMITY
We, ELEKTROBOCK CZ s.r.o., here declare that our product WS301 is in conformity
with the basic requirements and other respective provisions of the directive 1999/5/ES.
Issued: 01.11.2008
TECHNICAL PARAMETERS
Power supply 230 V/ 50 Hz
Frequency 433,92 MHz
Sensitivity < -102 dBm
Range 150 m (in free area), 20 m (in built-up area)
Output relay, max.16 A/ 250 VAC
Protection IP20 and higher acc. to the installation
Working temperature 0 to 40°C
Dimensions (LxWxD) 49,5 mm x 45,5 mm x 26 mm
v souladu s RoHS
Pb
LEAD FREE
MADE IN CZECH REPUBLIC
ELEKTROBOCK CZ s.r.o.
Blanenská 1763
Kuřim 664 34
Tel.: +420 541 230 216
www.elbock.cz
For remote ON / OFF and time control of electrical equip-
ment. WS301 can be controlled by up to 16-different
transmitters with different functions. Adjustable function
time is 1 to 8 hours.
WIRELESS RECEIVER
WS301WS301
ws301_en:Layout 1 18.2.2013 18:18 Page 4
Table of contents
Other ELEKTROBOCK Receiver manuals
