ELEKTROBOCK BPT001 User manual

Version 11.02
Wireless receiver for control of
electric heating devices
- UNDER SWITCH -
Operating instructions
Control of electric heating systems
Two-way radio communication at 433.92 MHz
The connected electric appliance is switched
according to the required temperature
Suitable transmitters (thermostats) for control are
BPT010 or BPT710
BPT001BPT001
bpt001_en:Layout 1 27.8.2015 15:28 Page 1

INSTALLATION
The device can only be installed by a person with adequate qualification!
The installation must be executed in a voltage-free state!
Wiring diagram:
230 V/ 50 Hz
L
N
max.
16 A
LN
FUNCTION BUTTON (R) :
SHORT PRESS (for about 1.5 s)
- for coding.
LONG PRESS (for about 5 s)
- RESET deleting the code from the
memory (the green and red LEDs
flash simultaneously).
BPT001 is used for switching the heating device in connec-
tion with the BPT010 or BPT710 thermostat. Its great
advantage is direct installation into the wiring box.
bpt001_en:Layout 1 27.8.2015 15:28 Page 2

1. Switch off the main circuit breaker.
2. Connect the receiver according to the diagram.
3. Switch on the main circuit breaker; the green diode is
flashing on the receiver; the receiver is ready for
further setting.
4. Shortly press the FUNCTION BUTTON for about 1.5 s
(the green and red diode are flashing alternately).
5. Activate the receiver on the thermostat (transmitter)
according to the manual for the given transmitter (BPT010
or BPT710).
6. If the code has been learned correctly, the green and
red diodes flash simultaneously.
LED 2
LED 1
empty memory, code not learned
code learned
FLASHING ALTERNATELY = code learning mode
FLASHING SIMULTANEOUSLY = code has been learned
SIMULTANEOUS LONG FLASH= code has been ERASED
relay switched
ERROR (if no signal is received from the transmit-
ter within approx. 6 hours, it switches to the 2-min-
ON / 8-min-OFF mode). LED 2 is only flashing if
the relay is on, i.e. for 2 minutes.
EXPLANATIONS: LIT UNLIT FLASHING
FUNCTION
ACTIVATION PROCEDURE
INDICATION DIODES
bpt001_en:Layout 1 27.8.2015 15:28 Page 3

TECHNICAL PARAMETERS
Power supply 230 V/ 50 Hz
Communication type two-way
Frequency 433.92 MHz
Sensitivity < - 92 dBm
Range 150 m (in free area), 20 m (in built-up area)
Output relay, max.16A/ 250 VAC
Protection class IP20 or higher acc. to installation
Protection rate II
Working temp. 0 to 40°C
Dimensions (LxWxD) 49.5 mm x 45.5 mm x 26 mm
in compliance with RoHS
Pb
LEAD FREE
BPT001 is suitable for switching heating panels, direct
heaters, radiant panels, heating mats, etc. It switches the con-
nected device according to the information received from the trans-
mitting unit (BPT010 or BPT710 thermostat). To be installed in
interior rooms. Do not locate near power lines!
MADE IN CZECH REPUBLIC
WARRANTY CERTIFICATE
(a 2-year warranty is granted for the product)
Product number: Date of sale:
Shop stamp:
Checked by:
In case of guarantee or
post-guarantee service, send
the receiver (including a copy
of the confirmed proof of
purchase) to the
manufacturer’s address.
DECLARATION OF CONFORMITY
We, ELEKTROBOCK CZ s.r.o., herewith declare that our product BPT001 conforms to
the basic requirements and other corresponding provisions of the directive 1999/5/ES.
Issued: 01.04.2012 on www.elbock.cz
ELEKTROBOCK CZ s.r.o.
Blanenská 1763
Kuřim 664 34
Tel.: [phone]
www.elbock.cz
bpt001_en:Layout 1 27.8.2015 15:28 Page 4