Elikon 2Easy EVD2-CC4C User manual

Please read this manual carefully before using the product you
purchase, and keep it well for future use.We reserve the right to
modify the specication in this manual at any time without notice.
2-Wire System
Power In-Use
Camera Interface
Model: EVD2-CC4C
CAM(1~4)
CAM1 CAM2
CAM3 CAM4
User Manual
ikon
EVD2-CC 4 C

DIP
RS485
CAM3
CAM4
BUS(IN)
BUS(OUT)
123456
ON
CAM2
CAM1
123456
ON
2-Wire System
Power In-Use
Camera Interface
Model: EVD2-CC4C
CAM(1~4)
CAM1 CAM2
CAM3 CAM4
INDICATORS BUTTONS
-1-
1.About EVD2-CC4C Unit
Description:
The camera interface EVD2-CC4C is a controller function device designed
for Elikon system to control camera. In addition, EVD2-CC4C can be
configured as camera converter working mode to fit before used distribuide
camera accessory of the project. For details, see later section 5.
2. Terminal Description
RS485:Reserved.
CAM1~2:Connect to
regular analog CCTV(the following called TYPE A Camera)
.
CAM3~4:Connect to 2 wire camera(the following called TYPE B Camera ); If
you want to connect CCTV to this port, it must be connected camera converter,
then the port can work usually(The camera converter is used to transform the 2
wire camera to analogue camera,for details, see camera converter manual).
BUS(IN):Connect to the bus line, no polarity.
BUS(OUT):Connect to the bus line, no polarity.
BUTTONS:Press CAM1~CAM4 button, it can control the corresponding
video output.
ikon EVD2-CC
4 C

-2-
1 2 3 4 5 6
ON
1 2 34 5 6
ON
1 2 345 6
ON
1 2 3 4 56
ON
Bit
DIP1~DIP2
set to the first EVD2-CC4C.
DIP3
DIP4
DIP5
DIP6
Bit State Description
1 2 3 4 56
ON
TYPE A Camera used. When EVD2-CC4C connected TYPE A Camera, it
should be set to ON.
TYPE B Camera used. When EVD2-CC4C connected TYPE B Camera, it
should be set to ON.
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
set to the second EVD2-CC4C.
set to the third EVD2-CC4C.
set to the fourth EVD2-CC4C.
When all EVD2-CC4C of the system are configured to connect the two
cameras(two TYPE A Cameras or two TYPE B Cameras ), it should be set to ON
When all EVD2-CC4C of the system are configured to connect the four
cameras(two TYPE A Cameras and two TYPE B Cameras ), it should be set to
OFF.
When the system connected programer, and programer connected two
cameras(the two cameras of the device is valid),it should be set to ON;
When the system don’t connected programer(or connected programer, but
programer don’t connected camera), it should be set to OFF.
INDICATORS:
1.Power: Working indicator, always on when the EVD2-CC4C work normally.
2.In-Use:Video output indicator, always on when the EVD2-CC4C output the video.
3.CAM(1~4):Video output indicator.
In-Use CAM(1~4) Description
CAM1 video output
CAM2 video output
CAM3 video output
CAM4 video output
*NOTE:
:It shows that the indicator ON;
:It shows that the indicator OFF.
DIP:DIP switches.
ikon EVD2-CC
4 C

-3-
3. Unit Mounting
Din rail
Din rail
Mounting Buckle
Step1: Mount the din rail to
the wall with screws ;
Step2: Pull down the
mounting buckle,then hang
the unit on din rail.
ikon EVD2-CC
4 C

-4-
RF CARD
BUS(IM) BUS(DS)
EVD2-624
AC~
BUS(IN) BUS(OUT)
EVD2-CC4C
1 2 3 4 5 6
ON
1# CCTV
2# CCTV
DT-CCU
Camera
BUS
GND VIDEO
BUS BUS 2-WIRESYSTEM
GND
VEDIO
DT-CCU
Camera
BUS
GND VIDEO
BUS BUS 2-WIRESYSTEM
GND
VEDIO
3# CCTV
4# CCTV
4. Wiring Diagram
4.1 Single door station and single EVD2-CC4C applications:
ikon EVD2-CC
4 C

-5-
4.2 Multi door station and two EVD2-CC4C (connected two
TYPE A
Cameras
) applications:
RF CARD
BUS(IM) BUS(DS)
EVD2-CC4C
AC~
BUS(IN) BUS(OUT)
EVD2-CC4C
1 2 3 4 5 6
ON
EVD2-OD4C
A B C D
RF CARD
(Device Address:1) (Device Address:0)
BUS(IN) BUS(OUT)
1 2 3 4 5 6
ON
a b
3# CCTV
4# CCTV
1# CCTV
2# CCTV
ikon EVD2-CC
4 C
EVD2-CC4C

-6-
4.3 Multi door station and two EVD2-CC4C (connected two
TYPE B
Cameras
)applications:
RF CARD
BUS(IM) BUS(DS)
EVD2-624
AC~
EVD2-OD4C
A B C D
RF CARD
(Device Address:1) (Device Address:0)
BUS(IN) BUS(OUT)
EVD2-CC4C
1 2 3 4 5 6
ON
BUS(IN) BUS(OUT)
1 2 3 4 5 6
ON
a b
CONVERTER
Camera
BUS
GND VIDEO
BUS BUS 2-WIRE SYSTEM
GND
VEDIO
CONVERTER
Camera
BUS
GND VIDEO
BUS BUS 2-WIRE SYSTEM
GND
VEDIO
1# CCTV
2# CCTV
CONVERTER
Camera
BUS
GND VIDEO
BUS BUS 2-WIRE SYSTEM
GND
VEDIO
CONVERTER
Camera
BUS
GND VIDEO
BUS BUS 2-WIRE SYSTEM
GND
VEDIO
3# CCTV
4# CCTV
NOTE: The system can connect programer(programer connected two TYPE B
Cameras ), but at this time, the DIP6 of EVD2-CC4C must be set to ON.
ikon EVD2-CC
4 C
EVD2-CC4C

In the program state, press and
hold "CAM1" button for 3 seconds
to switch the working mode. Then
it will return to standby
Working mode indicator:CAM(1~4)
(ash once)
-8-
2).Working mode configuration, the camera switching time setting, and
monitoring time setting.
In the standby, press and hold
"CAM4" button for 3 seconds, it will
enter the state of program.
indicator:IN-USE
(ash)
[SCU mode] [DCU mode]:
[DCU mode] [SCU mode]: (ash twice)
In the program state, press
and hold "CAM2" button for 3
seconds, it will enter the state of
camera switching time setting.
(1)the left light of indicator CAM (1 ~ 4)
starts ashing (ash once per second);
(2)Flash once to increase 3 seconds;
(3)Press any button to conrm the
setting and return to standby.
Note:
1. The maximum can be set to
99 seconds, to 99 seconds, then
automatically save and return to standby.
2. 6 seconds by default.
In the program state, press
and hold "CAM3" button for 3
seconds, it will enter the state of
monitoring time setting.
(1)the right light of indicator CAM (1 ~ 4)
starts ashing (ash once per second);
(2)Flash once to increase 15 seconds;
(3)Press any button to conrm the
setting and return to standby.
Note:
1. The maximum can be set to 900
seconds, to 900 seconds, then
automatically save and return to standby.
2. 600 seconds by default.
Note:In program state, if there isn’t any operation within 10s, or press any button, it will
return to standby.
ikon EVD2-CC
4 C

6. Specification
•Power Supply : DC24V;
•Working Temperature: -150C~+550C;
•Wiring: 2 wire,non-polarity;
•Dimension: 90(H)×72(W)×60(D)mm.
The design and specifications can be changed without notice to the user. Right to interpret
and copyright of this manual are preserved.
ikon EVD2-CC
4 C