DMP Electronics 734 Installation guide

INSTALLATION AND PROGRAMMING GUIDE
734 Weigand
Interface Module

About the 734............................................. 1
Power Supply......................................................... 1
Zone Terminals ...................................................... 1
Annunciators.......................................................... 1
Indicator LEDs ....................................................... 1
Form C Relay......................................................... 2
Programming Connection................................ 2
Keypad In and Out Connections ................... 2
PCB Features...............................................3
Install the 734 .............................................4
Mount the 734 ...................................................... 4
Wire the Electronic Lock.................................. 5
Isolation Relay ...................................................... 6
Install the 333 Suppressor ............................... 7
Wire the Zone Terminals................................... 8
Connect a Card Reader....................................10
Set the 734’s Address.......................................12
TABLE OF CONTENTS
Program the 734....................................... 15
Program Start Display ......................................15
Initialization Option ...........................................15
Initialize Confirm Option .................................16
Activate Zone 2 Bypass ...................................16
Zone 2 Bypass Time ..........................................17
Relock on Zone 2 Change...............................17
Activate Zone 3 Request to Exit ..................18
Zone 3 REX Strike Time...................................19
Activate On-board Speaker ...........................19
Custom Card Definitions ........................ 20
Card Options.......................................................20
Wiegand Code Length .....................................21
Site Code Position and Length .....................21
User Code Position and Length....................21
Site Code ..............................................................22
Enter Site Code..................................................23
Number of User Code Digits.........................23
No Communication with Panel ....................24
Remove Keypad.................................................25

Keypad Bus Wiring Specifications........ 26
Public Card Formats ................................27
Compliance Listing Specifications ........28
UL Commercial Fire..........................................28
UL Access Control.............................................28
ULC Commercial Burglary (XR150/XR550
Series Panels)......................................................28
Certifications............................................ 29
Underwriters Laboratory (UL Listed)........29
Product Specifications ........................... 30
Readers and Credentials ......................... 31

Digital Monitoring Products, Inc. | 734 Installation and Programming Guide 1
ANNUNCIATORS
An on-board programmable piezo provides local
annunciation at the 734. You can also connect a
variety of switched ground annunciators to the
734 for remote annunciation.
INDICATOR LEDS
The 734 provides three indicator LEDs. The red
LED turns on for the same duration as the door
strike relay. The yellow LED turns on for one
second to indicate receipt of a valid Wiegand
input. The green LED indicates that data is being
sent to the panel.
The 734 Wiegand Interface Module allows you to use the powerful built-in access control capability of
DMP Panels. DMP panels provide access control, arming, and disarming using proximity, mag-stripe,
biometric or other Wiegand-output authentication devices.
Connect a 734 to a DMP panel’s keypad bus or AX-Bus™to use the powerful built-in access control
capability of DMP panels. The 734 includes the following features:
POWER SUPPLY
The 734 operates at 12/24VDC from the power
supply supporting a door’s magnetic lock or
door-strike. It also provides a 10 Amp Form C
relay contact for lock control.
ZONE TERMINALS
Zones 1, 2, and 3 on the 734 can be programmed
for a variety of burglary or access control
applications. Zone 4 is a class B, style A circuit
that may be programmed as a fire zone.
ABOUT THE 734

2 734 Installation and Programming Guide | Digital Monitoring Products, Inc.
FORM C RELAY
The 734’s Form C relay draws up to 35mA of
current. Refer to the NC/C/NO (Dry Contact
Relay) and the Isolation Relay sections in this
document for more information.
PROGRAMMING CONNECTION
The 734 also provides a keypad programming
connection that allows you to use a standard
DMP LCD keypad for initial setup. Programming
can be completed using a keypad connected to
the 734 or from XR150/XR550 or
XR150INT/XR550INT Series panels.
KEYPAD IN AND OUT
CONNECTIONS
The keypad in (KYPD IN) connection receives
and transmits data to the panel keypad bus or
AX-Bus™.
The keypad out (KYPD OUT) connection receives
and transmits data out to other keypad(s) or
module(s). Install a dual connector four-position
harness to allow daisy chain connection to other
devices, up to the maximum number of devices
supported. XR150 Series panels support up to
8devices. XR550 Series panels support up to
16devices. When using the AX-Busses with
XR550 devices, you can have 32 doors,
expandable to 96.
When the 734 is powered from 24VDC, do
not connect devices to KYPD OUT header.

Digital Monitoring Products, Inc. | 734 Installation and Programming Guide 3
PCB FEATURES
RED
PROG
J2
RED
J5
J4
KYPD OUT
S1
J3
J1
DATA
XMT LED
WIEGAND
READ LED
RELAY
ON
NC
C
NO
GRN
YEL
RED + –
ON
Piezo
1234 5 6 7 810 11 12 13 14
9
LC ASRED WHT GRN BLK Z1 Z2 Z3 Z4+ Z4–RA GND GND
KYPD IN RED
DOOR RELAY
TERMINAL
WEIGAND
INPUTS
STATUS
INDICATOR
OUTPUTS ZONES
TO PANEL
KEYPAD BUS
OR AX-BUS
TO OTHER
KEYPAD BUS
OR AX-BUS
PIEZO
INDICATOR
LEDS
KEYPAD
PROGRAMMING
HEADER
ADDRESS DIP
SWITCHES
Figure 1: PCB Features

4 734 Installation and Programming Guide | Digital Monitoring Products, Inc.
INSTALL THE 734
The 734 comes in a high-impact plastic housing that you can mount directly to a wall, backboard,
or other flat surface.
For easy installation, the back and ends of the 734 housing have wire entrances. The back also
contains multiple mounting holes that allow you to mount the 734 on a single-gang switch box.
DMP recommends mounting the 734 near the protected door. See Figure2 for mounting hole
locations on the housing base.
1MOUNT THE 734
Mounting Hole
Figure 2: Mounting Hole Locations

Digital Monitoring Products, Inc. | 734 Installation and Programming Guide 5
The 734 provides a Form C (SPDT) relay for controlling locks and other electronically-controlled
barriers. The three relay terminals marked NO C NC allow you to connect the device wiring to
the relay for module control.
Use an additional power supply to power magnetic locks and door strikes. See Figures 3 and 4
for typical magnetic lock and door strike wiring.
The Form C relay draws up to 35mA of current and contacts are rated for 10 Amps (resistive)
at 12/24VDC. When connecting multiple locks to the Form C relay, the total current for all locks
cannot exceed 10 Amps. If the total current for all locks exceeds 10 Amps, problems may arise
and an isolation relay may be needed. See the Isolation Relay section for information.
2WIRE THE ELECTRONIC LOCK
PROG
J2
RED RED
KYPD IN
J4
J1
DATA
XMT LED
WIEGAND
READ LED
RELAY
ON
NCCNO
GRNYELRED
Model 333
Supressor
Normally Closed
–
+
Magnetic Door Lock
12/24 VDC
Power Supply
Figure 3: Typical
Magnetic Lock Wiring
PROG
J2
RED
J1
DATA
XMT LED
WIEGAND
READ LED
RELAY
ON
NCCNO
GRNYELRED
Model 333
Supressor
Normally Open
–+
DC Door Strike
12/24 VDC
Power Supply
Figure 4: Typical Door
Strike Wiring

6 734 Installation and Programming Guide | Digital Monitoring Products, Inc.
The Form C relay can control a device that draws less than 10 Amps of current. If a device draws
more than 10 Amp of current, or the sum of all devices controlled by the Form C relay exceeds
10 Amps, an isolation relay must be used. Refer to Figures 5 and 6 for isolation relay wiring.
3ISOLATION RELAY
RED
PROG
J2
RED
J5
RED
KYPD IN
J4
KYPD OUT
J1
DATA
XMT LED
WIEGAND
READ LED
RELAY
ON
NCCNO
GRNYELRED + –
Piezo
Model 333
Supressor
Normally Open
–+
Magnetic Lock
–+
Isolation Relay
To Panel
Keypad Bus
12/24 VDC
Power
Supply
NCCNO
Figure 5: Magnetic Lock with
an Isolation Relay
RED
PROG
J2
RED
J5
RED
KYPD IN
J4
KYPD OUT
J1
DATA
XMT LED
WIEGAND
READ LED
RELAY
ON
NCCNO
GRNYELRED + –
Piezo
Model 333
Supressor
Normally Open
–+
DC Door Strike
–+
Isolation Relay
To Panel
Keypad Bus
12/24 VDC
Power
Supply
NCCNO
Figure 6: Door Strike with
an Isolation Relay
(optional)