elink LNK-INJ-48-95W User manual

LNK-INJ-48-95W
Hardened 1 RJ45 Gigabit data input port to 1 RJ45 Gigabit PSE output port 95W PoE In ector
1 V1.0
This quick start guide describes how to install and use the Gigabit PoE In ector. The PoE In ector support LTPoE++ 95W high power, It is a perfect
choice for no power source of Ethernet environments.
Overview
The LNK-INJ-48-95W product is an Hardened PoE In ector which provides 2 port 10/100/1000Base-TX, 1
ports supports LTPoE++ 95W PSE (Power Sourcing Equipment) and compliant with IEEE 802.3at.
General
To ensure trouble free transportation and storage, all E-link products must be thoroughly inspected, tested
and properly packed before delivery. Check the product upon receipt for any visible damage which may
have been caused during shipment.
Package Content
 Hardened 1 RJ45 Gigabit data input port to 1 RJ45 Gigabit PSE output port 95W PoE In ector x 1
 Quick Start Guide x 1
Physical Description
Front Panel
Rear Panel

LNK-INJ-48-95W
Hardened 1 RJ45 Gigabit data input port to 1 RJ45 Gigabit PSE output port 95W PoE In ector
2 V1.0
Installation
DIN Rail Installation
LNK-INJ-48-95W can be installed on a DIN rail. Installation steps are as follows:
Wall Mount Installation
LNK-INJ-48-95W also can be installed on a Wall Mount. Installation steps are as follows:
Setup
a) Connect the LNK-INJ-48-95W to the power supply. Ensure the power supply in connected to a power
source and the PWR indicator is ON. If not, please ensure that the power cable is connected properly
and the power supply is functioning normally.
b) Connect the Ethernet Port to the network equipment (Switch or PC), Connect the PoE Out Port to the
Power Device (PoE IP-CAM).
c) After all cables are correctly connected, the indicators will be lit as per port status LEDs (page 3).
1. Tighten the screws to fix the
DIN Rail plate
1. Tighten the screws to fix the
DIN Rail plate
2. Mount the switch on the wall or
on a flat surface with 2 screws
piercing through the mounting
holes to secure it in position.
Upper
part
2. Lock the upper part of the
DIN
rail clip on the upper side of the
track. Press it until the metal part
move downward and a “click sound
is heard”
Press

LNK-INJ-48-95W
Hardened 1 RJ45 Gigabit data input port to 1 RJ45 Gigabit PSE output port 95W PoE In ector
3 V1.0
Inter ace
RJ-45 Pin Assignment
Pin
Signal Name
1
TP0+
Positive (VCC+)
2
TP0
-
Positive (VCC+)
3
TP1+
Negative (VCC-)
4
TP2+
Positive (VCC+)
5
TP2
-
Positive (VCC+)
6
TP1
-
Negative (VCC-)
7
TP3+
Negative (VCC-)
8
TP3
-
Negative (VCC-)
Power Connection
Pin
Description
V - V +
Power Input GND +48~57VDC
Cable Connections
Signal Type Cable Type Connector
Ethernet Cat. 5 or above RJ45
Power supply Power cable 2-pin Terminal Block
LED Indicators
Indicator Color Status Description
PWR Green ON Powered on
PoE Green
ON PoE is activated.
Blinking A Power Device (PD) is being detected.
OFF No device is connected or the connected device is not a PD.

LNK-INJ-48-95W
Hardened 1 RJ45 Gigabit data input port to 1 RJ45 Gigabit PSE output port 95W PoE In ector
4 V1.0
Dimensions o the LNK-INJ-48-95W (Unit: mm)
Functional Description
• 1 RJ45 Gigabit data input port to 1 RJ45 Gigabit PSE output port (Data + Power)
• Supports LTPoE++ (95W)
• Compatible IEEE802.3at PoE+
• Support 10/100/1000Base-TX
• Extensive LED indicators for PoE diagnostics
• 48~57VDC Terminal Block Power inputs
• Supports DIN-Rail and Wall-mount installation
• -40°C to 75°C ( -40°F to 167°F) operating temperature range