Biosan Bio RS-24 User manual

Multi Bio RS-24
Programmable rotator
for version
V.3AW
Operating Manual
Certificate
Medical–Biological
Research & Technologies

Contents
1. Safety precautions
2. General information
3. Getting started
4. Operation
5. Program setting
6. Specifications
7. Maintenance
8. Warranty and Claims
9. Declaration of Conformity
Page 2

Page 3
1. Safety precautions
The following symbols mean:
Caution! Make sure you have fully read and understood the present Manual
before using the equipment. Please pay special attention to
sections marked by this symbol.
GENERAL SAFETY
·Use only as specified in the operating instructions provided.
·The unit should be saved from shocks or falling.
·The unit must be stored and transported in a horizontal position (see package
label).
·After transportation or storage keep the unit under room temperature for 2-3 hrs
before connecting it to the electric circuit.
·Use only cleaning and decontamination methods recommended by the
manufacturer.
·Do not make modifications to the design of the unit.
ELECTRICAL SAFETY
·Connect only to a power supply with voltage corresponding to that on the serial
number label.
·Use only the external power supply unit provided with this product.
·Ensure that the external power supply connector is easily accessible during use.
·Disconnect the unit from the electric circuit before moving.
·Turn off the unit by disconnecting the external power supply from the power
socket.
·If liquid penetrates into the unit, disconnect it from the external power supply unit
and have it checked by a repair and maintenance technician.
DURING OPERATION
·Do not operate the unit in environments with aggressive or explosive chemical
mixtures.

·Do not operate the unit if it is faulty or has been installed incorrectly.
·Do not use outside laboratory rooms.
·Do not place a load exceeding the maximum load value mentioned in the
Specifications section of this Manual.
BIOLOGICAL SAFETY
·It is the user's responsibility to carry out appropriate decontamination if
hazardous material is spilt on or penetrates into the equipment.
2. General Information
Multi Bio RS-24 programmable rotator provides: 1) orbital rotational
motion, 2) reciprocal motion, 3) vibro motion of the platform in different planes
according to the microprocessor protocol. The protocol enables making not
only programs that include mixing motion of one particular type, but also
programs that alternate mixing motions of different types cyclically.
There are options for setting:
1) Speed and time of ordinary ROTATIONAL MOTION
(360º)of the platform for a time period 0 - 250 sec,
or non-stop with the speed of 1 - 100 rpm.
2) Segment of RECIPROCAL MOTION when
the direction of platform rotational motion from
the vertical plane is changing in turns within
the limits of the set segment (turning angle 1 -
90º for a time period 0 - 250 sec, or non-stop);
3.1) Segment and time of VIBRO MOTION
of the platform (turning angle 0 - 5º for a
time period 1 - 5 sec) run on the borders
of reciprocal motion segment. It is available
only when the reciprocal motion is ON;
3.2) PAUSE duration for temporary platform
motion stops (1 - 5 sec) when the vibro
motion is off (the turning angle of vibro
motion is set to zero) run on the borders
of reciprocal motion segment. It is available
only when the reciprocal motion is ON;
Page 4
·Do not operate the unit if it is faulty or has been installed incorrectly.
·Do not use outside laboratory rooms.
·Do not place a load exceeding the maximum load value mentioned in the
Specifications section of this Manual.
BIOLOGICAL SAFETY
·It is the user's responsibility to carry out appropriate decontamination if
hazardous material is spilt on or penetrates into the equipment.
2. General Information
Multi Bio RS-24 programmable rotator provides: 1) orbital rotational
motion, 2) reciprocal motion, 3) vibro motion of the platform in different planes
according to the microprocessor protocol. The protocol enables making not
only programs that include mixing motion of one particular type, but also
programs that alternate mixing motions of different types cyclically.
There are options for setting:
1) Speed and time of ordinary ROTATIONAL MOTION
(360º)of the platform for a time period 0 - 250 sec,
or non-stop with the speed of 1 - 100 rpm.
2) Segment of RECIPROCAL MOTION when
the direction of platform rotational motion from
the vertical plane is changing in turns within
the limits of the set segment (turning angle 1 -
90º for a time period 0 - 250 sec, or non-stop);
3.1) Segment and time of VIBRO MOTION
of the platform (turning angle 0 - 5º for a
time period 1 - 5 sec) run on the borders
of reciprocal motion segment. It is available
only when the reciprocal motion is ON;
3.2) PAUSE duration for temporary platform
motion stops (1 - 5 sec) when the vibro
motion is off (the turning angle of vibro
motion is set to zero) run on the borders
of reciprocal motion segment. It is available
only when the reciprocal motion is ON;
·Do not operate the unit if it is faulty or has been installed incorrectly.
·Do not use outside laboratory rooms.
·Do not place a load exceeding the maximum load value mentioned in the
Specifications section of this Manual.
BIOLOGICAL SAFETY
·It is the user's responsibility to carry out appropriate decontamination if
hazardous material is spilt on or penetrates into the equipment.
2. General Information
Multi Bio RS-24 programmable rotator provides: 1) orbital rotational
motion, 2) reciprocal motion, 3) vibro motion of the platform in different planes
according to the microprocessor protocol. The protocol enables making not
only programs that include mixing motion of one particular type, but also
programs that alternate mixing motions of different types cyclically.
There are options for setting:
1) Speed and time of ordinary ROTATIONAL MOTION
(360º)of the platform for a time period 0 - 250 sec,
or non-stop with the speed of 1 - 100 rpm.
2) Segment of RECIPROCAL MOTION when
the direction of platform rotational motion from
the vertical plane is changing in turns within
the limits of the set segment (turning angle 1 -
90º for a time period 0 - 250 sec, or non-stop);
3.1) Segment and time of VIBRO MOTION
of the platform (turning angle 0 - 5º for a
time period 1 - 5 sec) run on the borders
of reciprocal motion segment. It is available
only when the reciprocal motion is ON;
3.2) PAUSE duration for temporary platform
motion stops (1 - 5 sec) when the vibro
motion is off (the turning angle of vibro
motion is set to zero) run on the borders
of reciprocal motion segment. It is available
only when the reciprocal motion is ON;
·Do not operate the unit if it is faulty or has been installed incorrectly.
·Do not use outside laboratory rooms.
·Do not place a load exceeding the maximum load value mentioned in the
Specifications section of this Manual.
BIOLOGICAL SAFETY
·It is the user's responsibility to carry out appropriate decontamination if
hazardous material is spilt on or penetrates into the equipment.
2. General Information
Multi Bio RS-24 programmable rotator provides: 1) orbital rotational
motion, 2) reciprocal motion, 3) vibro motion of the platform in different planes
according to the microprocessor protocol. The protocol enables making not
only programs that include mixing motion of one particular type, but also
programs that alternate mixing motions of different types cyclically.
There are options for setting:
1) Speed and time of ordinary ROTATIONAL MOTION
(360º)of the platform for a time period 0 - 250 sec,
or non-stop with the speed of 1 - 100 rpm.
2) Segment of RECIPROCAL MOTION when
the direction of platform rotational motion from
the vertical plane is changing in turns within
the limits of the set segment (turning angle 1 -
90º for a time period 0 - 250 sec, or non-stop);
3.1) Segment and time of VIBRO MOTION
of the platform (turning angle 0 - 5º for a
time period 1 - 5 sec) run on the borders
of reciprocal motion segment. It is available
only when the reciprocal motion is ON;
3.2) PAUSE duration for temporary platform
motion stops (1 - 5 sec) when the vibro
motion is off (the turning angle of vibro
motion is set to zero) run on the borders
of reciprocal motion segment. It is available
only when the reciprocal motion is ON;
·Do not operate the unit if it is faulty or has been installed incorrectly.
·Do not use outside laboratory rooms.
·Do not place a load exceeding the maximum load value mentioned in the
Specifications section of this Manual.
BIOLOGICAL SAFETY
·It is the user's responsibility to carry out appropriate decontamination if
hazardous material is spilt on or penetrates into the equipment.
2. General Information
Multi Bio RS-24 programmable rotator provides: 1) orbital rotational
motion, 2) reciprocal motion, 3) vibro motion of the platform in different planes
according to the microprocessor protocol. The protocol enables making not
only programs that include mixing motion of one particular type, but also
programs that alternate mixing motions of different types cyclically.
There are options for setting:
1) Speed and time of ordinary ROTATIONAL MOTION
(360º)of the platform for a time period 0 - 250 sec,
or non-stop with the speed of 1 - 100 rpm.
2) Segment of RECIPROCAL MOTION when
the direction of platform rotational motion from
the vertical plane is changing in turns within
the limits of the set segment (turning angle 1 -
90º for a time period 0 - 250 sec, or non-stop);
3.1) Segment and time of VIBRO MOTION
of the platform (turning angle 0 - 5º for a
time period 1 - 5 sec) run on the borders
of reciprocal motion segment. It is available
only when the reciprocal motion is ON;
3.2) PAUSE duration for temporary platform
motion stops (1 - 5 sec) when the vibro
motion is off (the turning angle of vibro
motion is set to zero) run on the borders
of reciprocal motion segment. It is available
only when the reciprocal motion is ON;
·Do not operate the unit if it is faulty or has been installed incorrectly.
·Do not use outside laboratory rooms.
·Do not place a load exceeding the maximum load value mentioned in the
Specifications section of this Manual.
BIOLOGICAL SAFETY
·It is the user's responsibility to carry out appropriate decontamination if
hazardous material is spilt on or penetrates into the equipment.
2. General Information
Multi Bio RS-24 programmable rotator provides: 1) orbital rotational
motion, 2) reciprocal motion, 3) vibro motion of the platform in different planes
according to the microprocessor protocol. The protocol enables making not
only programs that include mixing motion of one particular type, but also
programs that alternate mixing motions of different types cyclically.
There are options for setting:
1) Speed and time of ordinary ROTATIONAL MOTION
(360º)of the platform for a time period 0 - 250 sec,
or non-stop with the speed of 1 - 100 rpm.
2) Segment of RECIPROCAL MOTION when
the direction of platform rotational motion from
the vertical plane is changing in turns within
the limits of the set segment (turning angle 1 -
90º for a time period 0 - 250 sec, or non-stop);
3.1) Segment and time of VIBRO MOTION
of the platform (turning angle 0 - 5º for a
time period 1 - 5 sec) run on the borders
of reciprocal motion segment. It is available
only when the reciprocal motion is ON;
3.2) PAUSE duration for temporary platform
motion stops (1 - 5 sec) when the vibro
motion is off (the turning angle of vibro
motion is set to zero) run on the borders
of reciprocal motion segment. It is available
only when the reciprocal motion is ON;
·Do not operate the unit if it is faulty or has been installed incorrectly.
·Do not use outside laboratory rooms.
·Do not place a load exceeding the maximum load value mentioned in the
Specifications section of this Manual.
BIOLOGICAL SAFETY
·It is the user's responsibility to carry out appropriate decontamination if
hazardous material is spilt on or penetrates into the equipment.
2. General Information
Multi Bio RS-24 programmable rotator provides: 1) orbital rotational
motion, 2) reciprocal motion, 3) vibro motion of the platform in different planes
according to the microprocessor protocol. The protocol enables making not
only programs that include mixing motion of one particular type, but also
programs that alternate mixing motions of different types cyclically.
There are options for setting:
1) Speed and time of ordinary ROTATIONAL MOTION
(360º)of the platform for a time period 0 - 250 sec,
or non-stop with the speed of 1 - 100 rpm.
2) Segment of RECIPROCAL MOTION when
the direction of platform rotational motion from
the vertical plane is changing in turns within
the limits of the set segment (turning angle 1 -
90º for a time period 0 - 250 sec, or non-stop);
3.1) Segment and time of VIBRO MOTION
of the platform (turning angle 0 - 5º for a
time period 1 - 5 sec) run on the borders
of reciprocal motion segment. It is available
only when the reciprocal motion is ON;
3.2) PAUSE duration for temporary platform
motion stops (1 - 5 sec) when the vibro
motion is off (the turning angle of vibro
motion is set to zero) run on the borders
of reciprocal motion segment. It is available
only when the reciprocal motion is ON;
·Do not operate the unit if it is faulty or has been installed incorrectly.
·Do not use outside laboratory rooms.
·Do not place a load exceeding the maximum load value mentioned in the
Specifications section of this Manual.
BIOLOGICAL SAFETY
·It is the user's responsibility to carry out appropriate decontamination if
hazardous material is spilt on or penetrates into the equipment.
2. General Information
Multi Bio RS-24 programmable rotator provides: 1) orbital rotational
motion, 2) reciprocal motion, 3) vibro motion of the platform in different planes
according to the microprocessor protocol. The protocol enables making not
only programs that include mixing motion of one particular type, but also
programs that alternate mixing motions of different types cyclically.
There are options for setting:
1) Speed and time of ordinary ROTATIONAL MOTION
(360º)of the platform for a time period 0 - 250 sec,
or non-stop with the speed of 1 - 100 rpm.
2) Segment of RECIPROCAL MOTION when
the direction of platform rotational motion from
the vertical plane is changing in turns within
the limits of the set segment (turning angle 1 -
90º for a time period 0 - 250 sec, or non-stop);
3.1) Segment and time of VIBRO MOTION
of the platform (turning angle 0 - 5º for a
time period 1 - 5 sec) run on the borders
of reciprocal motion segment. It is available
only when the reciprocal motion is ON;
3.2) PAUSE duration for temporary platform
motion stops (1 - 5 sec) when the vibro
motion is off (the turning angle of vibro
motion is set to zero) run on the borders
of reciprocal motion segment. It is available
only when the reciprocal motion is ON;

Page 5
4) Working period from 1 min to 24 hours,
or non-stop.
Apart from the unique operation modes the Multi Bio RS-24 rotator
possesses attractive miniature and elegant BioForm design and offers user-
friendly interface, which provides options not only for changing the program
during the operation, but also for simultaneous control over different steps of
mixing protocol realization.
The Multi Bio RS-24 programmable rotator will undoubtedly provide
increased methodical means to researchers working in the field of modern
molecular and cell biology and the developing biodiagnostics technology
based on the use of magnetic particles, for which unexpected and disturbing
hydrodynamic shifts of the reactants are essential.
The Multi Bio RS-24 programmable rotator is designed for mixing
biological solutions, cell suspensions, magnetic particles conjugated with
specific antibodies as well as incubation and cultivation of biological liquids
according to the operator set program.
The unit is applicable in all areas of laboratory research in biotechnology,
microbiology, chemistry, and medicine.

3. Getting started
3.1. Unpacking.
Remove packing materials carefully and retain them for future shipment
or storage of the unit.
3.2. Complete set.
Package contents:
Standard set
- Multi Bio RS-24 programmable rotator....................................1 piece
- PRS-26 platform u..................................................................1 piece
- External power supply unit ....................................................1 piece
- Operating Manual; Certificate.................................................1 copy
Optional accessories
-PRS-5/12 platform v.......................................................on request
-PRS-10 platform w..........................................................on request
-PRSC-22 platform x........................................................on request
-PRSC-10 platform y........................................................on request
-PRS-1DP platform z.......................................................on request
3.3. Set up:
- place the unit on the horizontal even working surface;
- plug the external power supply unit into the 12 V socket at the rear side
of the unit.
3.4. Platform replacement:
Unscrew the two fixing screws on the platform. Replace the platform and
install the new platform securing it with the screws. Fix the screw tightly.
Page 6

Select
Time (sec.)
Orbital
(rpm)
Reciprocal
(deg.)
Vibro/
/pause
Time
(hr:min)
Run
Stop
Multi-Rotator
o
1-90 0-24.00
1-5
o
0-5 1- 01 0
RUN
1-250 1-250
4. Operation
Recommendation during operation
Arrange the tubes symetrically to the rotation axis when loading.
4.1.Connect the external power supply unit to the electric circuit.
4.2.Place samples on the platform: microtubes - up to the end; vacutainers
and tubes with caps - halfsize.
4.3.Set the appropriate program and operation time (see the Program Setting
Section of this Manual) according to the methodical prescriptions.
4.4.Press the Run/Stop key (Fig.1/5) to start the program.
4.5.The platform motion will begin and the corresponding indication (RUN
(Fig.1/3) and the changing time values) will be shown on the display.
4.6.If the operation time is not set and the timer indicator (Fig.1/2) shows 0:00,
pressing the Run\Stop key will cause continuous operation of the rotator
until the Run\Stop key is pressed again.
4.7.If the operation time is set the platform movement will stop after its expiring
(flashing indication STOP will be shown on the display) and will start giving
a sound signal about the end of operation (press the Run\Stop key to stop
the signal).
4.8.Press the Run/Stop key to repeat the set program.
4.9.The rotator can be stopped at any
time during operation before the set
time expires if necessary by
pressing the Run/Stop key. In this
case the platform motion stops
when the platform achieves
horizontal position. Pressing the
Run/Stop key again will start the
program from the beginning
(countdown timer will be restarted).
Note: A step motor is used in this
model. Stopping the platform with
hand briefly is allowed and will not
damage the mechanical parts of
the device If the platform is
Page 7
Fig.1 Control panel
1
4
5
3
2

Page 8
stopped with hand during operation, the program does not stop and the
platform motion is automatically resumed after the platform is released.
4.10.Disconnect the external power supply unit from electric circuit to turn off
the unit.
5. Program setting
When setting program parameters please mind that the unit may be
unable to operate properly in reciprocal and vibration modes with
maximum load. The recommended load is indicated in table 1 on page12.
5.1. Press the Select key (Fig.1/1) to choose the parameter to change (the
active parameter is flashing).
5.2. Use the q and p keys (Fig.1/4) to set the necessary value (note: if the key
is pressed for more that 2 sec the numerical changes quickly).
5.3.Saving the program doesn`t require additional operations: the
microprocessor saves the last parameter changes as the working
program automatically.
5.4.The countdown timer is used to control the operation time. The timer can
be set for the period from 1 min to 24 hours.
5.5.The examples below show separate motion types and their available
combinations in cycles. The data to the right show the possible parameter
values for each type.
5.5.1. Orbital Rotation
Set the speed of Orbital rotation (1-
100 rpm), time of Orbital rotation (1 -
250 sec) and time for Reciprocal
motion to zero (OFF).
5.5.2. Orbital + Reciprocal Rotation
Set the speed (1-100 rpm) and time
(1 - 250 sec) of Orbital rotation. Set
the turning angle from vertical plane
(1-90º) and time (1 - 250 sec) for
Reciprocal motion. Switch off the
Vibro motion (set the time of Vibro
motion to 0 (OFF)).
Time (sec.)
o
1-90 o
0-5
1-250 OFF OFF
Orbital
(rpm)
Reciprocal
(deg.)
Vibro
/ pause
o
1-90 o
1-5
1-250 1-250 OFF
Time (sec.)
Orbital
(rpm)
Reciprocal
(deg.)
Vibro
/ pause
1-100
1-100

Page 9
5.5.3. Orbital + Reciprocal + Vibro
Set the speed (1-100 rpm) and time
(1 - 250 sec) of Orbital rotation.
Set the angle (1-90º) and time (1 -
250 sec) for Reciprocal motion. Set
the turning angle (0-5º) and time (1 - 5
sec) for Vibro motion.
Note that if the set time of Reciprocal motion is shorter or equal to the set
time of Vibro motion then the Reciprocal motion will be omitted (Orbital +
Vibro).
5.5.4.Orbital + Reciprocal + Pause
Set the speed (1-100 rpm) and time (1 -
250 sec) of Orbital rotation. Set the
turning angle (1-90º) and time (1 - 250
sec) for Reciprocal motion. Set the
angle of Vibro motion mode to zero.
Set the time for Vibro/pause mode (1 -
5 sec), which is the time of pause
duration.
Note that if the set time of Reciprocal motion is shorter or equal to the set
time of Vibro/pause mode, the Reciprocal motion mode will be omitted
(Orbital + Pause).
5.5.5.Reciprocal Rotation
Set the speed (1-100 rpm) for Orbital
rotation. Set time for Orbital rotation to
zero (OFF). Set the turning angle (1 -
90º) and time (1 - 250 sec) of
Reciprocal motion. Set the time for
Vibro motion to zero (OFF).
5.5.6. Reciprocal + Pause
Set the speed (1-100 rpm) of Orbital
rotation. Set time of Orbital rotation to
zero (OFF). Set the angle (1-90º) and
time (1 - 250 sec) of Reciprocal
motion. Set the time for vibro motion
o
0
o
1-90
1-250 1-250 1-5
Time (sec.)
Orbital
(rpm)
Reciprocal
(deg.)
Vibro
/ pause
o
1-90 o
0-5
OFF OFF1-250
Time (sec.)
Orbital
(rpm)
Reciprocal
(deg.)
Vibro
/ pause
1-5
1-250
o
1-90 o
0
OFF
Time (sec.)
Orbital
(rpm)
Reciprocal
(deg.)
Vibro
/ pause
1-100
1-100
1-100
o
1-90
1-250 1-250 1-5
o
1-5
Time (sec.)
Orbital
(rpm)
Reciprocal
(deg.)
Vibro
/ pause
1-100

type (1 - 5 sec), which is the time of pause duration. Set the angle of Vibro
type motion to zero.
5.5.7. Vibro + Reciprocal Rotation
Set the speed (1-100 rpm) of Orbital
rotation. Set the time of Orbital rotation
to zero (OFF). Set the angle (1-90º)
and time (1 - 250 sec) of Reciprocal
motion. Set the angle (0 - 5º) and time
(1 - 5 sec) of Vibro type motion.
Note that normally rotator performs
soft vibration (Vibro motion). However
there is a mode for hard vibration.
To perform hard vibration set the
turning angle of Reciprocal motion to
90º and the angle of Vibro type motion
to 1º (Hard Vibro).
When working with the unit in vibro motion mode for long period nonstop
and using the platform with rubber clamps, choose the tubes not longer
than 7 cm from cap till bottom.
Page 10
o
1-90
1-5
1-250OFF
o
0-5
1-100
Time (sec.)
Orbital
(rpm)
Reciprocal
(deg.)
Vibro
/ pause
o
90 o
1
OFF/1-250
1-5
1-250
Time (sec.)
Orbital
(rpm)
Reciprocal
(deg.)
Vibro
/ pause
1-100

Page 11
6. Specifications
The unit is designed for operation in cold rooms, incubators and closed
laboratory rooms at ambient temperature from +4°C to +40°C and maximum
relative humidity 80% for temperatures up to 31°C decreasing linearly to 50%
relative humidity at 40°C.
6.1. Rotation
Speed control range ..........................................................1– 100 rpm
Time setting range..............................................................0 – 250 sec
Vertical rotation movement ............................................................360º
6.2. Reciprocal rotation mode
Tilt angle range.................................................1º – 90° (increment 1º)
Time setting range ..............................................................0 - 250 sec
6.3. Vibro/pause mode
Tilt angle range....................................................0º – 5°(increment 1º)
Time setting range .................................................................0 – 5 sec
6.4. Digital time setting .................................1 min – 24 hours, or non-stop
6.5. Maximum load.............................................................................0.5 kg
6.6. Dimensions .............................................................365х195х155 mm
6.7. Input current/power consumption............................12V, 660 mA / 8 W
6.8. External power
supply unit ................... input AC 100-240 V 50/60Hz, output DC 12V
6.9. Weight*........................................................................................1.7 kg
* Accurate within ±10%.
* *PRS platforms are equipped with universal rubber clamps for different size tube fixation;
PRSC platforms have metal clamps able to hold heavier solutions (e.g.soil,sand).
Catalogue
number
BS-010117-HK
BS-010117-IK
Catalogue
number
BS-010117-GK
BS-010117-LK
BS-010117-JK
BS-010149-DK
Replacement parts
PRS-26 platform**
Tube diameter
20–30/10–16 mm
PRS-5/12 platform**
Tube volume
max. 50/2-15 ml
Optional
accessories
20–30 mm
PRS-10 platform** 50 ml
Capacity
5/12
10
Tube diameter
10–16 mm
Tube volume
from 2 to 15 ml
Capacity
26
10–16 mm
PRSC-22 platform** 15 ml
20–30 mm
PRSC-10 platform** 50 ml
22
10
Platform for microplates and racks for tall tubes 0.5 and 1 ml
(e.g. Thermo 3741MTX, 3742MTX, 3744MTX)
PRS-1DP platform**

Recommended load
Tubes Weight
Rotation Full load Up to 450 g.
Reciprocal rotation
Vibro motion Microtube type tubes only Up to 100 g.
Biosan is committed to a continuous programme of improvement and reserves the
right to alter design and specifications of the equipment without additional notice.
Up to 100 g. for platform with
rubber clamps; or 200 g. for
platform with metal clumps
26 Microtube type;
8-15 ml Falcon tubes,
2-50 ml Falcon tubes
Motion type
Table 1. Recommended loading
depending on motion types
Page 12

7. Maintenance
7.1. If the unit requires maintenance, disconnect the unit from the mains and
contact Biosan or your local Biosan representative.
7.2. All maintenance and repair operations must be performed only by
qualified and specially trained personnel.
7.3. Standard ethanol (75%) or other cleaning agents recommended for
cleaning of laboratory equipment can be used for cleaning and
decontamination of the unit.
Page 13

Page 14
8. Warranty and Claims
8.1. The Manufacturer guarantees the compliance of the unit with the
requirements of Specifications, provided the Customer follows the
operation, storage and transportation instructions.
8.2. The warranted service life of the unit from the date of its delivery to the
Customer is 24 months. Contact to your local distributor to check
availability of extended warranty.
8.3. If any manufacturing defects are discovered by the Customer, an
unsatisfactory equipment claim shall be compiled, certified and sent to
the local distributor address. Please visit www.biosan.lv, Technical
support section to obtain the claim form.
8.4. The following information will be required in the event that warranty or
post-warranty service comes necessary. Complete the table below and
retain for your records.
Multi Bio RS-24 programmable rotator
Model
Serial number
Date of sale

Version 3.03 - October 2012
9. Declaration of Conformity