Elk Products ELK-SWB28 User manual

ELK-SWB28
INSTALLATION
28” STRUCTURED WIRING BOX
2. Pilot drill 1/8” holes on the left
and right studs approximately
64” up from the oor and 1” from
the front edge. This allows for
1/2” wall nish (sheetrock, etc.)
with room for adjustment.
1“
The ELK-SWB28 is a universal structured wiring box featuring a pattern of hole-slot-hole that allows it to accommodate accessories,
circuit boards, shelves, brackets, and wiring modules from many different manufacturers. It may ush or surface mounted. Flush
mounting is ideal for hollow frame walls with studs on 16” centers. The minimum rough opening is 14.25” wide, 28.25” high, 3.5” deep.
The SWB28 can be adjusted for varying wall nish thicknesses and the hinged lid extends beyond the box edges approximately 5/8”
which easily conceals uneven cutouts of the wallboard edges.
4. Pull wires through one or more of
the entry holes. The design of the
SWB28 allows wires to be organized
along the sides. Plastic wire ties can
be used to secure wiring as shown.
3. If desired, install an electrical outlet in the rectangular knockout on
the lower ange. A standard one gang electrical “J” box is mounted
using #6 Flat Head Self-Tapping Screws (not included)
NEW CONSTRUCTION ROUGH-IN
Tie Wrap
L532 11/14
ELK PRODUCTS, INC.
PO Box 100 • Hildebran, NC 28637 • 828-397-4200 • 828-397-4415 FAX
http://www.elkproducts.com • email: [email protected] PRINTED IN USA
ELK
PRODUCTS, INC.
5. To install the lid, start two (2) 6-32 x 3/8” type F sheet metal screws
into the top and bottom holes of the hinge as shown below. Hold lid
against left side of box and align the two 6-32 screw heads with the
slotted (key) holes on the box.
Move lid right until the screws engage the slots, then lower into place.
BOX MAY BE ADJUSTED FORWARD AND BACK AS NEEDED. Tight-
en the rst 2 screws, then install the remaining 4 screws. Door should
open and close freely.
INSTALLING THE LID AFTER WALLBOARD INSTALLATION AND/OR PAINTING
1. Remove any conduit knockouts prior to mounting the box.
Position box and install a #10 screw
(not included) in the upper left and right
horizontal slots using the pilot holes.
Adjust front edge of box 1” from the
stud face and tighten screws. Install
other two screws.
Onlythesetwo(2)knockoutsmaybeusedifanM1Controlisinstalled!
Thesetwo(2)knockoutsCANNOTbeusedif
anM1Controlisinstalled.

7. Install camlock onto box lid and mount any remaining devices.
8. If desired, two (2) #10 sheet metal screws can be installed in the right
side of the lid (upper and lower) to make the box more secure against
tamper. In addition, the SWB28 provides mounting holes for two
tamper switches.
Optional Accessories For SWB28
ELK-SWD1 1.75” Gromment Donuts (2)
ELK-SWG Circuit Board Glides (2)
ELK-SWNS1 Nylon Standoffs for SWP (10)
ELK-SWP 4.5” Multipurpose Adapter Plate
ELK-SWP3 3” Multipurpose Adapter Plate
ELK-SWS Battery Shelf
6. The box has 8 columns of repeated 2-hole patterns labeled A, B, D, E,
F, H, J, & K (see diagram). In each 2-hole pattern one hole in slightly
larger than the other. These are for plastic Circuit Board Glides (p/n
ELK-SWG). The small hole ts a 6/32 type “F” mounting screw and the
large hole is for the half-moon locator tab on the bottom of each glide.
To mount a circuit board, pick a pair of 2-hole patterns in the same
vertical column that have their larger holes facing one another. The
distance between the large holes determines the size (length) of the
circuit board that may be mounted. The available mounting lengths in
inches are: 3-1/2”, 4”, 6”, 8”, 9-3/8”, and 11”.
Loosely start a 6/32” screw in the top (small) hole of a 2-hole pattern.
Place the slotted edge of a Circuit Board Glide under the screw and
make sure the half-moon tab ts into the larger hole. The groove for
the board should face down. Tighten screw with a long screwdriver.
In the lower 2-hole pattern loosely start a 6/32” screw. Attach the
second circuit board glide using the same procedures. The groove
for the board should face up.
The circuit board should slide freely into
the slide grooves. If not, simply loosen
or tighten mounting screws to adjust
glide for a secure t.
1
6
ABC D F GH J K
M1 Alternate #1 Mount Holes (Top)
E
2
3
4
5
7
8
9
10
11
12
13
15
16
17
18
25
26
20
21
22
23
24
27
28
I
19
14
31/2"Board
4"Board
6"Board
8"Board
11"Board
93/8"Board
BoardsizesthatfittheElk‐SWB28utilizing
theElk‐SWGVerticalGlides
Pleasenote:Themountingholepatternsin
thetop14"halfoftheSWB28arerepeatedin
thebottom14"withoneexception.The31/
2"mountingpatternonlyappearsonceinthe
top14"half(upperrightcorner).
14"
14"
4"Board
6"Board
8"Board
11"Board
93/8"Board
M1 Alternate #2 Mount Holes (Mid)
M1 Alternate #3 Mount Holes (Low)