Elk BAPPU-evo Installation instructions

EN The original operating manual is in German.
Status: 08/2019

Multi-measuring device for workplace analysis BAPPU-evo
Inhalt
1. BAPPU-evo 4
1.1. Sym ols..................................................................................................5
1.2. Security alert...........................................................................................5
Use personal protective equipment (PPE)....................................5
1.3. General information................................................................................6
1.4. Qualification of the operating personnel.................................................6
1.5. O serve accident prevention regulations................................................6
1.6. Intended use...........................................................................................6
1.7. Technical changes..................................................................................7
1.8. Initial assem ly.......................................................................................7
1.9. Delivery contents....................................................................................7
1.10. Optinal Sensor........................................................................................7
1.11. Optional accessories...............................................................................7
1.12. Disposal..................................................................................................8
1.13. Support...................................................................................................8
1.14. Cali rating BAPPU-evo...........................................................................8
1.15. Technical data and measuring range......................................................8
Permissi le operating conditions..................................................8
Measuring range and tolerances..................................................9
Specifications of the measurement with VOCOO-sx..................10
Availa le sensors in VOCOO-sx.................................................10
Specifications for noise level measurement...............................10
Frequency weighting and permissi le errors..............................11
Using the optional noise level measurement cali rator..............11
Special features for the measurement of illuminance.................12
Special features for temperature measurement.........................12
Supply Voltage............................................................................12
Charging function........................................................................13
2. Glossary 13
2.1. BAPPU-measurement...........................................................................13
2.2. Work place list.......................................................................................13
2.3. Type of work place................................................................................14
2.4. Measurement profile (profile)................................................................14
2.5. Overview of measurement results (overview).......................................14
2.6. Measurement value details...................................................................14
2.7. Repeat measurement...........................................................................15
2.8. Recording..............................................................................................15
3. Operating instructions 15
3.1. Display and touch screen......................................................................15
Sensitive areas...........................................................................15
Function uttons.........................................................................15
3.2. Key oard...............................................................................................15
page 1 comp a c t manual status 07/2019

BAPPU-evo Multi-measuring device for workplace analysis
3.3. Connections.......................................................................................16
3.4. Help ar.............................................................................................16
3.5. Background Colour............................................................................16
4. Main menu 17
4.1. BAPPU-measurement.......................................................................17
4.2. Recording..........................................................................................17
4.3. Settings..............................................................................................18
5. Recording preparation 18
5.1. Modifying the measurement profile (Profile)......................................18
5.2. Editing the work place.......................................................................19
Allocating the work place type.................................................19
Allocating the work place type profile......................................19
Deleting measurement data....................................................20
6. Measurement sequen 20
6.1. Perform measurement.......................................................................20
Evaluation................................................................................20
Saving measured values.........................................................21
Hold / freeze readings.............................................................21
Finishing or cancelling a measuring range..............................21
6.2. Measurement result overview............................................................21
6.3. Detailed view.....................................................................................22
6.4. Repeat measurement........................................................................22
7. (Long-term) recording) 23
7.1. Selecting the measuring range..........................................................23
7.2. Adjusting the interval settings............................................................23
7.3. Memory type......................................................................................24
7.4. Starting and stopping the recording...................................................24
7.5. Key oard lock....................................................................................24
7.6. ta le-mounting pin.............................................................................24
8. Settings 25
8.1. Language...........................................................................................25
8.2. Display/Energy..................................................................................25
8.3. Measurement settings (measurement)..............................................25
Humidity compensation (rf-compensation)..............................25
Time-weighting (time weighting noise)....................................25
Area (area noise).....................................................................26
C-peak measurement (C-peak measurement)........................26
Clothing insulation value (PMV CLO)......................................26
PMV–Calculation (PMV air velocity)........................................26
8.4. Time...................................................................................................26
8.5. Firmware update................................................................................27
8.6. User Init.............................................................................................27
8.7. Measurement profile (Profile)............................................................27
page 2 comp a c t manual status 07/2019

Multi-measuring device for workplace analysis BAPPU-evo
9. BAPPU standard software 28
9.1. License general terms and conditions..................................................28
9.2. Installation.............................................................................................28
9.3. Starting the programme and connecting BAPPU..................................29
9.4. Settings.................................................................................................29
9.5. Online....................................................................................................29
9.6. Extra......................................................................................................29
9.7. Defining the type (defining the type of work place)...............................30
9.8. Work place names and type definition (data retrieval)..........................32
9.9. Reading and evaluating measurement values......................................33
9.10. User-defined display.............................................................................33
9.11. Measurement profile (Profile)................................................................33
10. BAPPU-time software 34
10.1. License general terms and conditions..................................................34
10.2. Installation.............................................................................................35
10.3. Starting the programme........................................................................35
10.4. Computer test.......................................................................................35
10.5. Working with BAPPU-time....................................................................35
10.6. Operating and reading the internal data counter..................................36
Data Logger port.........................................................................36
Configuring the data logger........................................................36
Reading the BAPPU-evo data counter.......................................37
10.7. Opening and displaying recorded data.................................................38
10.8. Display options for the graphs..............................................................40
Specific selection........................................................................40
Zoom in/zoom out.......................................................................41
Ruler...........................................................................................41
Measurement value ta le...........................................................41
10.9. Selecting a recording............................................................................42
10.10. Mean value calculator...........................................................................42
10.11. Recording with the PC..........................................................................42
10.12. Starting a recording...............................................................................43
Online-Monitor............................................................................44
Graphic display...........................................................................45
The end of the recording.............................................................45
10.13. General.................................................................................................46
Exporting files.............................................................................46
Printing........................................................................................46
Right mouse utton.....................................................................46
10.14. Guarantee.............................................................................................46
Operator responsi ility................................................................47
Instruction y the operator..........................................................47
11. Notes 48
page 3 comp a c t manual status 07/2019

BAPPU-evo Multi-measuring device for workplace analysis
1. BAPPU-evo
The product is a multi-measuring device for the orienting measurement of
environmental characteristics at workplaces.
The following parameters can e measured: air temperature, glo e temperature,
relative humidity, air speed, class 2 noise level with C-peak to 137 dB, illuminance
class C, flicker frequency, luminance, luminance ratio, CO2 Value (optional sensor
= opS), TVOC (opS), CO value (opS) and particulate matter sensor PM1, PM2.5,
PM10 (opS).
Developed and manufactured y:
The contents of this manual are su ject to unannounced changes that reflect
technical progress.
Technical questions please send to: support@ appu.de
© Copyright - The copyright to this documentation remains at: ELK Gm H
The instructions for use contain the most important information for operating the
product safely. The instructions for use must always e kept close at hand and
always accessi le near the product.
This instruction manual meets the requirements of the Product Safety law (ProdSG)
When operating the product, follow the instructions for use and the product
specifications.
The contents of the important instructions for use must e read, understood and
followed in all respects y anyone responsi le for the assem ly and operation of the
product. This is especially for the safety instructions in Chapter 2. Following the
safety instructions and instructions will help to prevent accidents, malfunctions, faults
and property damage.
page 4 comp a c t manual status 07/2019

Multi-measuring device for workplace analysis BAPPU-evo
1.1. Symbols
The following sym ols are used in this operating manual:
This note indicates the risk of injury and / or death as well as
health hazard, if certain rules of conduct are disregarded.
Tipp:
Tipp: Important notes and information for installation, operation and
maintenance.
Please note and read the instructions for use.
1.2. Security alert
During assem ly and operation, the following safety instructions must e o served:
Use personal protective e uipment (PPE)
When using the product, it may e necessary to wear safety shoes.
When using the product, wearing protective clothing may e required.
When using the product, it may e necessary to wear protective gloves.
When using the product, wearing an industrial helmet may e required.
When operating the product for noise measurement, it may e
necessary to wear ear protection.
While charging, do not leave the device unattended.
page 5 comp a c t manual status 07/2019

BAPPU-evo Multi-measuring device for workplace analysis
1.3. General information
Risk of burns: The product is subjected to an operating
temperature of up to 50 ° C. There is a risk of burns on
housing parts.
Avoid installation errors: The installation of the product is
only permitted by ualified personnel . Assembly errors
can lead to malfunction!
1.4. ualification of the operating personnel
Work with and on the product may only e carried out y instructed persons of the
operator with the requisite knowledge and experience.
1.5. Observe accident prevention regulations
The relevant accident prevention regulations as well as the other generally accepted
safety rules must e o served.
1.6. Intended use
The product may only e used to measure the a ove measured varia les at
workplaces according to Ar StättV (see location) within the scope of the
environmental conditions and permissi le measuring ranges elow.
The various sensors may only e used for intended measurements or for
measurements within the cali rated or permissi le measuring range. For
measurements outside the cali rated range, readings may e outside the allowa le
tolerance; measuring unintended readings or taking readings outside the accepta le
range may damage the sensors or even the entire product.
The product can e used at workplaces. Workplaces are workspaces or other places
in uildings on the premises of an esta lishment, places in the open air on the
premises of an esta lishment, places on construction sites, if they are intended for
use for workplaces.
A workplace includes, in particular, places on the premises of an esta lishment or
construction site to which workers have access in the course of their work, traffic
routes, escape routes, emergency exits, warehouses, machines and ancillary rooms,
sanitary facilities, canteens, reaks and preparedness rooms, first aid rooms,
accommodation as well Facilities for the operation of the workplace, fire-
extinguishing equipment, utilities, lighting, ventilation and air conditioning, signaling,
power distri ution systems, doors and gates, moving walks, escalators, loading
ramps and ladders.
page 6 comp a c t manual status 07/2019

Multi-measuring device for workplace analysis BAPPU-evo
Any use eyond its intended use is deemed to e contrary to the intended purpose.
The manufacturer is not lia le for resulting damages.
Proper use also includes o serving and following all instructions in this documentation.
1.7. Technical changes
The manufacturer assumes no lia ility for technical changes y the operator or y
another manufacturer.
If technical changes are made to the experimental unit y the operator or y another
manufacturer, this must e considered as a safety-related consideration.
1.8. Initial assembly
The initial assem ly and all related work will e carried out y the manufacturer.
1.9. Delivery contents
BAPPU-evo comes equipped with an integrated data-counter for long-term recording,
a sturdy case, atteries (4 x Mignon (HR6, NiMh), power supply, USB ca le, carrying
strap, a mini tripod and operating instructions.
1.10. Optinal Sensor
Anemometer-evo, Glo e-Thermometer, Vocoo-sx
1.11. Optional accessories
A calibration unit for checking the accuracy of and for adjusting the noise level
measurements on site.
•An additional battery pack
•A high-quality charger for charging external atteries. This unit helps you get
the maximum capacity from the attery. It can even e used for charging an
additional attery pack.
page 7 comp a c t manual status 07/2019

BAPPU-evo Multi-measuring device for workplace analysis
1.12. Disposal
Please dispose of all packaging and o solete devices in
the correct manner. In the interest of the environment, the
device must not e thrown away as normal household
waste. You should arrange for the proper disposal of the
device.
Your local government will e a le to provide you with the
respective collection points and their opening hours.
1.13. Support
ELK Gm H | Glad acher Straße 232 | D-47805 Krefeld
Fon: [phone] | Fax: [phone] I
info@ appu.de | www. appu.de
1.14. Calibrating BAPPU-evo
Detectors and sensors are prone to drifting and change. In order to guarantee high-
quality results with BAPPU-evo, we recommend that a factory cali ration of the unit
should e carried out every twelve months.
BAPPU-evo displays a corresponding message in the main menu one month efore
the end of the cali ration interval. This can e deactivated under "Settings / Display".
However, it is then possi le that the results of the measurements are outside the
tolerance range.
1.15. Technical data and measuring range
Permissible operating conditions
Temperature: range from -10 °C to +50 °C I Relative humidity: range from 0 to 95%
(non-condensing) I The optional sensors might have deviating operating conditions:
With the optional CO sensor (only in BAPPU-VOCOO to serial num er xxx/05):
temperature: range from -0 °C to +50 °C (this also applies for storage)
Caution: Storage below 0 ° C can permanently damage the
CO sensor.
With option particular matter (in BAPPU-VOCOO-sx):
temperature: from -0 °C to +40 °C (this also applies to storage)
page 8 comp a c t manual status 07/2019

Multi-measuring device for workplace analysis BAPPU-evo
Measuring range and tolerances
Measurement Range Tolerance Sensor Resolution
Air temperature -20...50 °C +/- 0,5 °C PT 1000 Sensor 0,1 °C
Globe
temperature**
0...70 °C
-20...70 °C
+/- 0,5 °C
+/- 2 °C
Integ. temperature
semiconductor
sensor
0,1 °C
Rel. humidity 10...90% +/- 4% r.H. Capacitive humidity
sensor
0,10 %
Air speed* 0,0...5 m/s +/- 10 % f. MV.**
+/- 3 Digit
Thermo-anemometer 0,01 m/s
Noise level
(Class 2) in accordance
with DIN EN 61672-1:
2014
30...135 dB(A) A-
evaluation Slow/Fast
c-peak= 137 dB
+/-1 dB(A) at 1 kHz
inherent noise <25 dB(A)
Precision electret
condenser
microphone
0,1 dB
Illuminance
(Class C) in accordance
with DIN 5032-7: 2017
50...30.000 Lux
1...50 Lux
V-lambda adjustment 7,5 %
Cosine-correction 4 %
Linearity 3 %
plus +/- 1 Lux
Silicon photo-
element with
adapted spectral
sensitivity 1 Lux
Flicker fre uency 0...1000 Hz +/- 0,2 Hz Silicon photodiode 0,1 Hz
Luminance
Maximum display
brightness
Luminance contrast
10 ... 2000 cd/ m
1/60...60/1 (under
typical workplace
lighting conditions)
+/- 10% f. MV.**
+/- 10 cd/ m
as for the luminance
Silicon photo-
element with
adapted spectral
sensitivity
0,1 cd/ m
1 Digit
CO2 (carbon dioxide)* 0...10.000 ppm +/- 75 ppm +/- 5 % f. M.V.** Non-dispersive
infrared
1 ppm
TVOC (total volatile
organic compounds)*
100...2000 ppb
(isobutylenä .)
+/- 100 ppb +/- 15 % v.M.** metal 1 ppb
CO (carbon-monoxide)* 0...500 ppm +/- 5 ppm +/- 5 % v.M.** electrochemical
(Lifespan up to to 10
years)
1 ppb
Particular Matter
(pm)*
PM1:
0...1000 μg/m3
PM2.5:
0...1000 μg/m3
PM10:
0...1000 μg/m3
PM1; PM2.5 :
0...100 μg/m3 +/-15 μg/m3
101...1000 μg/m3 +/-15 % v.M.**
PM10:
0...100 μg/m3 +/-30 μg/m3
101...1000 μg/m3 +/-30 % v.M.**
at 0...40°C; 10...70 % rF
optical 0,1 μg/m3
BAPPU-evo: L = 260 mm, B = 94 mm, H = 40 mm *optional sensor Technical
modifications are subject to factory settings without prior notice. **from Measured Value
Independent from the classification of individual measurements, the BAPPU-evo has
een designed as a measuring device for performing indicative measurements.
Therefore, BAPPU-evo should e used according to these prerequisites.
page 9 comp a c t manual status 07/2019

BAPPU-evo Multi-measuring device for workplace analysis
Specifications of the measurement with VOCOO-sx
Caution: The VOC sensor needs after switching on about 3
minutes to stabilize. During the heating phase, the LED of the
VOC- sensor is flushing.
Available sensors in VOCOO-sx
When switched on, the LEDs signal the availa le sensors.
Specifications for noise level measurement
Properties Value
Measurement tolerance +/- 1dB
Reference conditions: 87,5 dB at 1 kHz
Resolution 0,1 dB
Level range 30 – 95 dB and 80 – 110 dB
Fre uency range 31,5 – 8 kHz
Fre uency weighting A
Reference fre uency/range 1000 Hz / 87,5 dB
Direction of reference Perpendicular to the middle of the microphone
Accoustic centre Centre of microphone diaphragm
Screen refresh 0,33 s
The noise level measurement values are made using frequency weighting A. For
carrying out frequency weightings, “slow” (1 second) and “fast” (125 milliseconds)
are availa le (please refer to page 25, chapter 8.3, “Measurement settings
(measurement)”).
The standard configuration of the level range is “auto”. We recommend using this
setting. Changing the level range to “Low” or “High” can e selected in the main
menu under properties/settings (please refer to chapter 8.3, “Measurement settings
(measurement)”). When the range is exceeded, it will e indicated - depending on
how long this takes - at least every second. All specifications for noise level
measurements refer to a BAPPU-evo that is not fitted with extra accessories and
optional sensor devices.
page 10 comp a c t manual status 07/2019

Multi-measuring device for workplace analysis BAPPU-evo
Fre uency weighting and permissible errors
Nominal frequency in Hz A-evaluation in dB Permissible error
class 2 in dB
31,5 -39,4 +/- 3
1000 0 +/- 1,5
4000 1 +/- 3
8000 -1,1 +/- 5
Using the optional noise level measurement calibrator
For checking the accuracy of the noise level
measurement, especially in cases when the device
hasn't een used for some time, we recommend
recali rating the device using the optional cali rator.
In cases of special environmental conditions, such
as high ceilings or high humidity levels, BAPPU-evo
should e checked using the cali rator efore and
after the measurement has een made.
In order to recali rate BAPPU-evo, please follow the
following steps: When you are in the process of
using the measurement designation “Noise” to take
a measurement (please refer to page Fehler:
Referenz nicht gefunden, chapter Fehler: Referenz
nicht gefunden “Fehler: Referenz nicht gefunden”).
By clicking you will access noise level
cali ration mode.
In order to carry out the cali ration, the cali rator should e connected to the front side
of the housing, at the pointed end of the device using the adaptor. Following this, press
or “adjust” on the display and the recali ration will start.
Caution: Please ensure you deduct the correction factors
pertaining to the calibrator. These are printed on the
corresponding adaptor.
page 11 comp a c t manual status 07/2019

BAPPU-evo Multi-measuring device for workplace analysis
Special features for the measurement of illuminance
BAPPU-evo is used to measure lighting conditions at a typical work place, including,
for example, those specified in DIN 5035-6:2006-11. With other conditions, larger
measuring tolerances may occur.
Description BAPPU-evo Permissible error class C
DIN 5032-7
V(λ)-Adjustment 7,5 % 9,0 %
Cosine correction 4,0 % 6,0 %
Linearity 3,0 % 5,0 %
Calibration error 1,0 % 2,0 %
Display device errors 1,0 % 7,5 %
Total errors* 18,0 % 20,0 %
*The total of all errors allowed is larger than the total errors allowed (DIN 5032-7).
In order to get the est results, it is advisa le to place the illumination sensor in a
horizontal position at the work place to e measured. The ta le mounting pin can e
used for positioning the device correctly.
Special features for temperature measurement
With the key a dew point calculation is availa le. This is calculated on the
asis of the determined measured values of air temperature and relative humidity. At
the dew point temperature, the maximum saturation of the air with steam is reached.
If it falls elow, liquid water, condensation falls on surfaces that fall elow this
temperature, down.
Supply Voltage
The voltage can e supplied from a power supply unit, rechargea le attery or, in
special cases, a attery. If the voltage supply is too low, the device will turn itself off.
In order to guarantee smooth operation, we recommend using GP ReCyko+ NiMh
HR6 210AAHCB 2050mAh 1.2V rechargea le attery packs. The external voltage
supply for using the power supply unit provided or the USB port of the PC is
indicated y on BAPPU-evo.
Caution: We recommend the use of rechargeable batteries.
Caution: If the symbol for external power supply does not flash
or flashes, the power supply of the USB port is insufficient.
Caution: Do not leave the device unattended while charging.
page 12 comp a c t manual status 07/2019

Multi-measuring device for workplace analysis BAPPU-evo
Charging function
Using the rechargea le atteries delivered with the device, the integrated charging
function can charge a fully discharged rechargea le attery in eight hours. In order to
do this, your BAPPU-evo must e turned on and connected to the power supply unit
via the USB connection.
Caution: Please make sure that the rechargeable batteries are
placed in the battery compartment before commencing
charging.
Using the USB port of a PC or laptop to charge the atteries will result in a charging
time of 16 hours. In order to guarantee a longer operating time with the BAPPU-evo,
we recommend using a high-quality external charger (please refer to page 7, chapter
1.11 „Optional accessories“) , and charging the atteries in long intervals (30 to 50
charging cycles). This will help to greatly prolong the service life and the capacity of
the rechargea le atteries
The charging state of the attery is indicated on BAPPU-evo screen y the attery icon
that gradually fills up.
Ti p:
T i p : The charging will commence approximately one
minute after the device has een connected to the USB
power supply. In cases where the rechargea le atteries
in the attery compartment are not recognised, you have
the possi ility to start the charge programme manually y
pressing the attery icon.
2. Glossary
2.1. BAPPU-measurement
The term BAPPU-measurement refers to sample measurements taken from currently
recorded measurement values carried out y BAPPU-evo and their su sequent
storage in a pre-defined location in the memory.
Apart from sample measurement characteristics, single measurements that can last
several minutes can e carried out (noise levels, air speed).
2.2. Work place list
The work place contains all of the information necessary for assigning a name to the
measurement sequence, as well as organising the value profiles and the selected
measurements (profile). The information includes:
page 13 comp a c t manual status 07/2019

BAPPU-evo Multi-measuring device for workplace analysis
•work place num er (memory filing num er)
•work place name (the desired sequence of characters that identify the work
place, with a maximum of 20 characters)
•The type of work place assigned
•The assigned measurement sequence (profile)
The work place list provides an overview of all existing work places, num ering them
from 1 – 99. Names and profiles can e assigned to the num ers. The list is
displayed y selecting the option “Measurements” in the main menu field.
2.3. Type of work place
The work place type is where the threshold values and set values measurement
ranges are stored. The results of the individual measurements are indicated as
either red, am er, or green in the evaluation ar.
2.4. Measurement profile (profile)
This allows you to select the measuring ranges that are to e used and to select the
individual work places (please refer to page 18 „Modifying the measurement profile
(Profile)“).
The measurement sequence profile gives the user the opportunity to switch
individual measuring ranges on or off. Up to nine different measurement sequence
profiles can e defined.
Each work place can e assigned an individual measurement sequence profile.
Therefore, it is possi le to carry out measurements that are relevant for a specific
work place.
2.5. Overview of measurement results (overview)
This screen displays the most important measuring ranges and measurement data
pertaining to a specific work place.
2.6. Measurement value details
The detailed view shows all of the values and results stored in the memory for a
specific measuring range. Moreover, a repeat measurement can e started from this
screen. You can search the measurement ranges using . In addition, the
measurement ranges that have een deactivated in the measurement sequence
profile are indicated here. Pressing “hold” during a measurement will also take you
to the detailed view.
page 14 comp a c t manual status 07/2019

Multi-measuring device for workplace analysis BAPPU-evo
2.7. Repeat measurement
When carrying out a repeat measurement, individual measurement ranges can e
called up, deselected, or shown again. The remaining measurement ranges in the
measurement sequence are not affected.
2.8. Recording
When carrying out a long-term recording, the device allows you to set the intervals
when the selected measurement ranges are to e recorded in the internal memory.
The progress of the measurement values eing recorded is shown in the thum nail
view.
Important information: In order to be able to utilise the data
that has been recorded, you will need to purchase a licence for
“BAPPU-time” software!
3. Operating instructions
3.1. Display and touch screen
The device features a touch screen. This means that in most cases the user is a le to
operate the device using on-screen commands.
Sensitive areas
Apart from the key oard, the functions of the D-pad are
availa le on the screen (see diagram )
Function buttons
The F1, F2 and F3 function uttons, which are la elled
according to their function, can e found on the lower
display.
3.2. Keyboard
The F1, F2 and F3 function uttons, which are to e
found eneath the display, offer different functions
according to the information eing displayed.
page 15 comp a c t manual status 07/2019

BAPPU-evo Multi-measuring device for workplace analysis
The D-pad is used for navigating the cursor, while the OK utton is used to confirm
the selection. The user can find additional commands for the D-pad on the upper
task ar.
3.3. Connections
The connection socket is located on the lower side of the device housing.
•Headphone – Headphone/Analogue Line Out
•micro SD slot – Card reader for microSD card for memory expansion
•USB Device/DC IN – Connection to PC or power supply (for data transfer)
•USB Stick – flash drive – receptacle for USB flash drive
•External sensor (2x) - Glo e temperature / CO2 / Anemometer-evo / from
version: 4000/10
•MiniSaver – Kensington compati le
3.4. Help bar
The help ar, which is at the top edge of the
screen, descri es the key oard functions that are availa le. The function of the
right/left and up/down arrow keys as well as the function of the OK utton is shown.
Please note that under certain circumstances the three function keys at the ottom
edge of the screen can e used for additional functions.
3.5. Background Colour
The ackground colour indicates the operating mode of the device. A dark grey
ackground indicates either menu items or data from the memory. During the
measuring process a light ackground is used.
The changing ackground colours make it easy to see if the device is currently
measuring (light ackground) or if values that have already een measured are
displayed (dark ackground).
page 16 comp a c t manual status 07/2019

Multi-measuring device for workplace analysis BAPPU-evo
4. Main menu
After switching on the device – after a start message
and a self-test – the main menu will appear.
Ti p:
T i p : You can access the main menu
any time y holding the utton.
From the main menu you can access the functions
descri ed elow.
4.1. BAPPU-measurement
By selecting the menu item “measurement”, you are
presented with an overview of the work place and the
work place list. Edit the work places (name, type of
work place, measurement sequence profile) and/or
start measuring.
Measurement sequences that are marked with “*”
already store measurement data.
By pressing the “Current” softkey, the user is presented
with an up-to-date overview of the current
measurement values.
The “Edit” softkey is used for editing the work place
name and the type of work place as well as the
measurement sequence profile.
Ti p:
T i p : The "current" view does not
represent all availa le measuring
ranges. All availa le measuring
ranges are only visi le during the
complete run of a series of
measurements.
4.2. Recording
Here the user can access the settings for the counter and commence the internal long-
term recording. After a short time, and depending upon the intervals that have een
selected, the user will e a le to see the progress of the selected measuring range.
Caution: In order to be able to utilise the data that has been
recorded, you will need to purchase a licence for “BAPPU-
time” long-term recording software. This is available as an
option and is not provided with the standard delivery.
page 17 comp a c t manual status 07/2019

BAPPU-evo Multi-measuring device for workplace analysis
4.3. Settings
All settings, such as language, display and energy functionality, profile settings, to
name ut a few can e carried out here (please refer to page 25, chapter 8
„Settings“).
5. Recording preparation
5.1. Modifying the measurement profile (Profile)
The measurement sequence profile is where you can define which measuring
ranges are availa le in the measurement sequence. Two profiles, namely “All” (all
measuring ranges) and “Standard”, are availa le. However, the user can set up eight
additional user-defined profiles. The default setting is that all measuring areas are
activated for all profiles. You can customise the profiles in accordance with your
needs.
Ti p:
T i p : Measuring ranges
from external sensors,
which are not connected,
do not appear in the
measurement sequence,
even in cases when they
are activated.
In order to e a le to edit additional profiles, select
“Settings” in the main menu and select “Profile”.
Confirm the selection y pressing . Profile “01 ALL”
is permanently assigned and contains all measuring
ranges.
All other profiles can e changed according to your
requirements. Simply select the profile you wish to
change and then press . You can use the and cursor uttons to
navigate the measuring ranges.
You can use to select or deselect a specific measuring range. Alternatively, you
can make the selection using the touch screen.
The measurement sequence profiles can e managed using “BAPPU-Standard”
software (please refer to page 33, chapter 9.11, „Measurement profile (Profile)“).
page 18 comp a c t manual status 07/2019