Ellington WOD52ABZ5X User manual

Installation Guide
For Models:
WOD52ABZ5X
WOD52BK5X
WOD52BR5X
WOD52CS5X
WOD52EV5X
WOD52GV5X
WOD52MBK5X
WOD52WW5X
Table of Contents:
Safety Tips. pg. 1
Unpacking Your Fan. pg. 2
Parts Inventory. pg. 2
Installation Preparation. pg. 3
Hanging Bracket Installation. pg. 3
Fan Assembly. pgs. 4 - 5
Wiring. pg. 6
Canopy Assembly. pg. 6
Blade Assembly. pg. 7
Testing Your Fan. pg. 7
Light Kit Assembly (Optional). pg. 8
Troubleshooting. pg. 9
Parts Replacement. pg. 9
Warranty. pg. 9
Parts Replacement. pg. 9
Warranty. pg. 9
net weight of fan: 15 lbs. (6.8 KG)
E192641
PRINTED IN CHINA
FOR WET LOCATIONS
F.P.O.
F.P.O.
For Placement Only
For Placement Only
READ THESE INSTRUCTIONS
AND SAVE THEM FOR FUTURE USE

page 1
SAFETY TIPS.
WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box
or circuit panel before you begin the fan installation or before servicing the fan or installing accessories.
1. Read all instructions and safety information carefully before installing your fan and save these
instructions.
2. Make sure all electrical connections comply with Local Codes or Ordinances and the National
Electrical Code. If you are unfamiliar with electrical wiring or if the house/building wires are
different colors than those referred to in the instructions, please use a qualified electrician.
3. Make sure you have a location selected for your fan that allows clear space for the blades to
rotate, and at least seven (7) feet (2.13 meters) of clearance between the floor and the fan blade
tips. The fan should be mounted at least thirty (30) inches (76 centimeters) from walls or other
upright structures.
4. The outlet box must be securely mounted to the ceiling support joist and they must be capable
of supporting at least 35 pounds (16 kilograms). The box must be supported directly by the
building structure. Use only UL listed outlet boxes marked "FOR FAN SUPPORT."
WARNING: To reduce the risk of fire, electrical shock, or personal injury, mount to the outlet box
marked "Acceptable for Fan Support," and use the mounting screws provided with the outlet box.
Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan
support and may need to be replaced. Consult a qualified electrician if in doubt.
WARNING: To reduce the risk of fire, electrical shock, or personal injury, wire nuts/wire connectors
provided with this fan are designed to accept only one12 gauge house wire and two lead wires from
the fan. If your house wire is larger than 12 gauge or there is more than one house wire to connect to
the two fan lead wires, consult an electrician for the proper size wire nuts/wire connectors to use.
WARNING: To reduce the risk of personal injury, electrical shock or death, this fan must be connected
to a supply circuit that is protected by a Ground Fault Circuit Interrupter (GFCI).
5. Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL
listed and marked suitable for use with the model fan you are installing. Switches must be UL
general use switches. Refer to the instructions packaged with the light kits and switches for
proper assembly.
6. After installation is complete, check that all connections are absolutely secure.
7. After making electrical connections, spliced conductors should be turned upward and pushed
carefully up into the outlet box. The wires should be spread apart with the grounded
conductor and the equipment-grounding conductor on opposite sides of the outlet box.
WARNING: To reduce the risk of electrical shock and fire, do not use this fan with any variable (rheostat)
wall control.
8. Do not operate the reverse switch until the fan has come to a complete stop.
9. Do not insert anything between the fan blades while they are rotating.
WARNING: To reduce the risk of personal injury, do not bend the blade arms during assembly or after
installation. Do not insert objects into the path of the blades.
WARNING: To avoid personal injury or damage to the fan and other items, be cautious when working
around or cleaning the fan.
10. Do not use water or detergents when cleaning the fan or fan blades.A dry dust cloth or lightly
dampened cloth will be suitable for most cleaning.
NOTE: The important safety precautions and instructions appearing in the manual are not meant to
cover all possible conditions and situations that may occur. It must be understood that common sense
and caution are necessary factors in the installation and operation of this fan.
F.P.O.
For Placement Only

1. Unpacking Your Fan.
2. Parts Inventory.
Carefully open the packaging. Remove items
from Styrofoam inserts. Remove motor housing
and place on carpet or Styrofoam to avoid
damage to finish. Do not discard fan carton or
Styrofoam inserts should this fan need to be
returned for repairs.
Check against parts inventory that all parts have
been included.
a. canopy. 1 piece
b. hanging bracket. 1 piece
c. 4-inch downrod and hanging ball. 1 piece
d. motor housing. 1 piece
e. weatherproof hanging ball cover. 1 piece
f. weatherproof yoke cover. 1 piece
g.blade arm. 5 pieces
h. blade. 5 pieces
i. hardware packs
page 2
ab
c
f
h
i
d
g
e
F.P.O.
For Placement Only

3. Installation Preparation.
To prevent personal injury and damage, ensure
that the hanging location allows the blades a
clearance of 7ft. (2.13m) from the floor and 30in.
(76cm) from any wall or obstruction.
This fan is suitable for room sizes up to 400
square feet (37.2 square meters).
4. Hanging Bracket Installation.
page 3
ON
OFF
ON
OFF
12ft. - 20ft.
12ft. - 20ft.
(3.66m - 6.1m)
(3.66m - 6.1m)
blade edge
7 feet
(2.13m)
(76cm)
30
inches
spring washers
flat washers
outlet box screws
Turn off circuit breakers to current fixture from breaker
panel and be sure operating light switch is turned to the
off position.
WARNING: Failure to disconnect power supply prior to
installation may result in serious injury.
Remove existing fixture.
WARNING: When using an existing outlet box, be sure the
box is securely attached to the building structure and can
support the full weight of the fan. Ensure it is clearly
marked "Suitable for Fan Support." If not, it must be
replaced with an approved outlet box. Failure to do so can
result in serious injury.
Install hanging bracket to outlet box using original
screws, spring washers and flat washers (size 8 or M5)
provided with new or original outlet box.*If installing
on a vaulted ceiling, face opening of hanging bracket
towards high point of ceiling. Arrange electrical wiring
around the back of the hanging bracket and away from
the bracket opening.
*Note: It is very important that you use the proper
hardware when installing the hanging bracket as this will
support the fan. Please make certain that you purchase any
hardware that is missing in order to install the hanging
bracket properly.
F.P.O.
For Placement Only
hanging bracket
This fan can be mounted with a downrod
on a normal or vaulted ceiling.The hanging
length can be extended by purchasing a longer
downrod (0.5 in./1.27cm diameter). Continue to
Section 5 on page 4 after "Hanging Bracket
Installation" for those instructions.This fan can be
mounted with flushmount installation on a
normal ceiling only. Continue to Section 6 on page
5 after "Hanging Bracket Installation" for those
instructions.
Installation requires these tools:
Phillips screwdriver, flathead screwdriver,
adjustable pliers or wrench, stepladder, wire
cutters, and rated electrical tape.
Vaulted ceiling
angle is not to
exceed 25 degrees.
downrod
installation flushmount installation

NOTE: The important safety precautions and
instructions appearing in the manual are not
meant to cover all possible conditions and
situations that may occur. It must be understood
that common sense and caution are necessary
factors in the installation and operation of this fan.
page 4
5. Fan Assembly (with downrod).
yoke set screw
downrod
weatherproof
yoke cover
canopy
pin
clip
motor
housing
set screw hole
set screw
hanging ball
stop pin
A
B
weatherproof hanging
ball cover
electrical wiring
hanging
ball
F.P.O.
For Placement Only
If you wish to extend the hanging length of
your fan, you must remove the hanging ball
from the 4-inch downrod provided to use with
an extended downrod (sold separately). [If you
wish to use the 4-inch downrod, please proceed to
instructions following the dotted line below.]
To remove hanging ball, loosen set screw on
hanging ball, lower hanging ball and remove
stop pin. Slide hanging ball off the original
downrod, A, and slide it down the longer
downrod, B (the top of the downrod should be
noted as having a set screw hole; use this hole
when setting the set screw). Insert stop pin into
top of extended downrod and raise hanging
ball. Be sure stop pin aligns with slots on the
inside of the hanging ball.Tighten set screw
securely.
Slide downrod through canopy and
weatherproof yoke cover.
Thread electrical wires through downrod and
pull extra wire slack from the upper end of the
downrod.
Tip: Apply small piece of electrical tape to the
ends of the electrical wires to keep them
together when threading them through the
downrod.
Loosen yoke set screw(s) and nut(s). Place
downrod into the motor housing yoke and
insert pin and clip.Tighten yoke set screw(s)
and nut(s) securely.
Remove electrical tape from electrical wires and
thread one wire through each hole in the
weatherproof hanging ball cover. Pull
weatherproof hanging ball cover down
securely over hanging ball (on downrod).

5. Fan Assembly (with downrod). (cont.)
With the hanging bracket secured to the outlet
box and able to support the fan, you are now ready
to hang your fan. Grab the fan firmly with two
hands. Slide downrod through opening in hanging
bracket and let hanging ball rest on the hanging
bracket.Turn the hanging ball slot until it lines up
with the hanging bracket tab.
Tip: Seek the help of another person to hold the
stepladder in place and to lift the fan up to you
once you are set on the ladder.
Continue to "Wiring" section for wiring diagram.
page 5
F.P.O.
For Placement Only
hanging ball slot
hanging bracket tab
6. Fan Assembly (flushmount).
Remove and set aside canopy cover to reveal 6
holes. Notice that 3 holes are larger.
Note:Weatherproof yoke cover is not used with
this type of installation.
If there are only 3screws in top of motor
housing, please proceed to next paragraph. If
there are 6screws in top of motor housing,
remove every other screw and lock washer.
Thread wiring through canopy. Place canopy
over yoke, aligning larger holes in canopy with
the 3 existing screws in top of motor housing.
Insert the 3 screws and 3 lock washers that were
removed (if there were only 3 screws located in
top of motor housing, these screws/lock
washers will be located in one of the hardware
packs) into the remaining holes. Securely
tighten these screws.
To prepare the fan for wiring, hang fan onto
hanging bracket by sliding the canopy over the
hanging bracket tab. (Use one of the non-
slotted holes on the rim of the canopy to do so.)
Continue to "Wiring" section for wiring diagram.
canopy
canopy cover
canopy
motor housing
hanging bracket
tab
canopy
motor housing
yoke

page 6
F.P.O.
For Placement Only
7.Wiring.
Important: Be sure outlet box is properly grounded or that a
ground wire (GREEN or Bare) is present.
Make sure all electrical connections comply with Local
Codes or Ordinances and the National Electrical Code. If you
are unfamiliar with electrical wiring or if the house/building
wires are different colors than those referred to below, please
use a qualified electrician.
Note: Excess lead wire length from the fan can be cut and
stripped to the desired length.
WARNING: To reduce the risk of personal injury, electrical
shock or death, this fan must be connected to a supply
circuit that is protected by a Ground Fault Circuit
Interrupter (GFCI).
When downrod is secured in place on the hanging
bracket, electrical wiring can be made (diagram 1) as
follows:
Connect BLACK wire from fan to BLACK wire from ceiling
with wire nut provided.
Connect WHITE wire from fan to WHITE wire from ceiling
with wire nut provided.
Connect all GROUND (GREEN) wires together from fan to
BARE/GREEN wire from ceiling with wire nut provided.
Since this fan does not come with a light kit, you will need
to cap off the BLUE wire with a wire nut (as shown with
arrow in diagram 1).
* Wrap all wire nuts with electrical tape as an extra safety
measure.
This fan is remote control adaptable.
NOTE: If you elect to purchase a light kit for the fan,
electrical wiring can be made (diagram 2)as follows:
Connect BLACK and ¹BLUE wire from fan to BLACK wire
from ceiling with wire nut provided.
Connect WHITE wire from fan to WHITE wire from ceiling
with wire nut provided.
Connect all GROUND (GREEN) wires together from fan to
BARE/GREEN wire from ceiling with wire nut provided.
¹ If you intend to control the fan light with a separate light
switch, connect BLUE wire from fan to the BLACK supply
from the independent switch.
black
black
white
white
blue
black supply wire
ground
(green
or bare)
white supply wire
diagram 1 *
from ceiling
from fan
ground
(green or bare)
black
black
white
white
blue
black supply wire
ground (green
or bare)
white supply wire
diagram 2 *
from ceiling
from fan
ground
(green or bare)
8. Canopy Assembly.
Temporarily raise canopy to hanging bracket to
determine which 2 screws align with slotted holes
in canopy, and then lower canopy and partially
loosen these 2 screws. Remove the other 2 screws
and set aside.
Now, lift canopy to hanging bracket, aligning
slotted holes in the canopy with loosened screws
in hanging bracket.Twist canopy to lock. Re-insert
the other 2 screws and secure all screws with
Phillips screwdriver.
canopy
hanging bracket

page 7
F.P.O.
For Placement Only
9. Blade Assembly.
Time Saver: Washers for blade screws can be set
on each blade screw prior to installing blades.
Locate 15 blade attachment screws and washers
in one of the hardware packs. Hold blade arm up
to blade and align holes. Insert 3 blade
attachment screws and washers with fingers first
and then tighten screws securely with Phillips
screwdriver. Repeat procedure for remaining
blades.
Remove blade arm screws and lock washers from
fan motor and set aside. Then, if applicable,
remove motor shipping pads and discard. Align
blade arm holes with motor screw holes and
attach blade arm with blade arm screws and lock
washers. Before securing screws permanently,
repeat this procedure with remaining blade
arms. Secure all screws.
blade arm screws
lock washers
blade attachment
screws and washers
motor housing
blade arm
blade
pull chain
extension
reverse switch
weatherproof cover
on reverse switch
10.Testing Your Fan.
It is recommended that you test fan before
finalizing installation. Restore power from circuit
box and light switch (if applicable).Test fan speeds
with the pull chain. Start at the OFF position (no
blade movement). First pull will set the fan to HI.
Second pull will set the fan to MEDIUM.Third pull
will set the fan to LOW. Fourth pull will again set
the fan to OFF setting. If fan does not function,
please refer to "Troubleshooting" section to solve
any issues before contacting Customer Service.
Turn fan completely off when operating the
reverse switch. Set to recirculate air depending on
the season.
Note: Do NOT remove weatherproof cover from
reverse switch.
Pull chain extension supplied or a custom pull
chain extension (sold separately) can be attached
to fan.

F.P.O.
For Placement Only
11. Light Kit Assembly (Optional).
page 8
switch housing cap
bulb
[representative only]
center cap
motor housing
switch housing cap
switch housing
diagram a
diagram b
diagram c
blue wire white wire
hex nut
lock washer
WARNING: Failure to disconnect power
supply at main panel prior to light kit assembly
may result in serious injury.
If you wish to use your fan WITH a light kit (sold
separately), it MUST be UL-APPROVED for WET
LOCATIONS or OUTDOOR USE.
Remove 3 screws from switch housing. Remove
switch housing cap from switch housing. (Refer to
diagram a.)
Locate BLUE and WHITE wires in the switch housing
labeled FOR LIGHT. Remove and discard cardboard
label and plastics that hold these 2 wires together.
Remove wire nuts from these same wires as well--
save for later use. (Refer to diagram a.)
If your light kit is to be mounted directly to switch
housing, remove 3 screws from light kit fitter. (Refer
to diagram b.) Make wire connections as described
below.
If your light kit is to be attached by a threaded rod,
remove hex nut and washer from light kit fitter.
Punch center cap out of switch housing cap with a
screwdriver. Push wires from light kit fitter through
hole in middle of switch housing cap and screw
switch housing cap onto threaded rod followed by
the washer and hex nut that were previously
removed. (Refer to diagram c.) Tighten hex nut over
washer for a secure fit. Make wire connections as
described below.
Connect WHITE wire from light kit fitter to WHITE
wire from switch housing. Connect BLACK wire from
light kit fitter to BLUE wire from switch housing. Use
wire nuts when making the connections. Align holes
in top of light kit fitter or switch housing cap with
holes in switch housing. Re-insert screws that were
previously removed and securely tighten all 3 screws.
Attach glass shade(s) to light kit fitter using the
hardware provided. (Refer to diagram d.)
Note: If you are installing a bowl fixture, the bulb(s)
must be installed first.
Install bulb(s) specified by the light kit. If you are
installing a halogen bulb, be sure not to handle glass
directly with your fingers as oil from the skin may
shorten the life of the bulb.
Important: When changing bulb(s), remember to
allow bulb(s) and glass shade(s) to cool before
touching.
glass shade
[representative only]
light kit fitter
[representative only]
light kit fitter
[representative only
for using threaded
rod to attach light kit]
light kit fitter
[representative only
for directly connecting
light kit]
diagram d
switch housing cap
wire nuts

F.P.O.
For Placement Only
Troubleshooting.
page 9
For parts and information, please refer to
"Parts Inventory" on page 2.
Ellington Customer Support:
1.800.527.1292
www.ellingtonfans.com
Parts Replacement.
Warranty.
Ellington 30-Year Limited Warranty:
ELLINGTON/LITEX INDUSTRIES, LTD. warrants this fan to the
original household purchaser for indoor use under the
following provisions:
1-YEAR WARRANTY: ELLINGTON/LITEX INDUSTRIES, LTD.
will replace or repair any fan which has faulty performance
due to a defect in material or workmanship. Contact Litex
Customer Service at 1-800-527-1292 to arrange for return
of fan. Return fan, shipping prepaid, to Litex Industries, Ltd.
We will repair or ship you a replacement fan, and we will
pay the return shipping cost.
5-YEAR WARRANTY: ELLINGTON/LITEX INDUSTRIES, LTD.
will repair or replace, at no charge to the original
purchaser, any fan motor that fails to operate satisfactorily
when failure results from normal use.
RETURN FAN MOTOR ONLY, shipping prepaid, to Litex
Industries.We will repair or ship purchaser a replacement
motor and Litex will pay the return shipping cost.
6 to 30-YEAR WARRANTY: ELLINGTON/LITEX INDUSTRIES,
LTD. will repair the fan, at no charge to the original
purchaser for labor only, if the fan motor fails to operate
satisfactorily when failure results from normal use.Parts
used in the repair will be billed to the purchaser at
prevailing prices at time of repair.
The purchaser shall be responsible for all costs incurred
in the removal, reinstallation and shipping of the product
for repairs.
This warranty does not apply when damage from
mechanical, physical, electrical or water abuse results in
causing the malfunction. Deterioration of finishes or other
parts due to time or exposure to salt air is specifically
exempted under this warranty.
Neither Litex Industries nor the manufacturer will
assume any liability resulting from improper installation or
use of this product. In no case shall the company be liable
for any consequential damages for breach of this, or any
other warranty expressed or implied whatsoever.This
limitation as to consequential damages shall not apply in
states where prohibited.
WARNING: Failure to disconnect power
supply prior to troubleshooting any wiring issues may
result in serious injury.
Problem: Fan fails to operate.
Solutions:
1. Check wall switch to fan.
2.Verify that reverse switch is set completely in
either direction.
3. Check to be sure fan is wired properly.
Problem: Light kit (optional) not lighting.
Solutions:
1. Check wall switch to fan.
2. Check that bulbs are installed correctly.
3. Check to be sure wires in canopy are wired
properly.
Problem: Fan operates but light fails (if applicable).
Solutions:
1. Check that bulbs are installed correctly.
2. Check to be sure wires in canopy are wired
properly.
3.Verify that wires in switch housing are connected
properly with wire nuts.
4. Replace defective bulbs with same type of bulb.
Problem: Fan wobbles.
Solution:
1. Use the balancing kit in one of the hardware
packs.