Elmes Electronic ST100H-3K User manual

Email: [e-mail] Web: www.elmes.pl ©Elmes Electronic 09.2014 - All rights reserved.
THREE RELAY OUTPUTS UNIVERSAL CONTROL RECEIVER
ST100H-3K
Elmes Electronic ST100H-3K receiver is designed for individual control of up to 3 devices. It features three separated relay
output terminals. Applied KEELOQ
®
code-hopping system ensures that each radio transmission is encrypted allowing high level of
system security. Following, are main features of ST100H-3K features:
operation with 1, 2 or 3 remote control (further referred to as a “remote”) transmitter’s buttons,
individual or sequential control of 2 or 3 devices,
ON / OFF mode (bistable mode),
ON / OFF mode with automatic set OFF of outputs after programmed time from 0.5 sec to 4 hours (monostable mode).
General Operation
The ST100H-3K receiver is compatible with all Elmes Electronic remotes operating at 433.92 MHz. In operation with Elmes Elec-
tronic made 4 , 8, 32 channel remotes it offers independent control of 3 devices connected to its outputs (see pt. 2 below for de-
tails). Operating with one remote’s button (e.g. single button remote) sequential control mode is available (see pt. 3 below).
The receiver also includes 3 wired logic inputs marked 1, 2, 3 and COM that allow control of its outputs by external, switch-
es. Operation with control switches is identical as that of with remotes.
Four different operation modes can be selected with jumpers JP1 and JP3 as below:
1. Jumper JP1 shorted, JP3 shorted –remote 1 and 2 buttons control output channels 1 and 2 respectively.
2. Jumper JP1 shorted, JP3 opened –as above plus remote button 3 controls receiver output number 3.
3. Jumper JP1 opened –sequential control mode activated for remote/s and wired switch/s –see chart below for details:
X–output channel ON
O–output channel OFF
The receiver can automatically switch off its outputs (connected devices) after pre-programmed time. The function is
active only if step 2 of Programming Procedures is performed. All three outputs set off after time lapse since last use
of a remote or a wired switch. Performing step 3 of Programming Procedures sets the function off and monostable
operation only (on/off) is restored.
Installation
Side figure shows example of three lamps (L1..L3) control wiring
diagram.
ST100H-3K control unit 230VAC wiring terminals:
L- 230VAC mains supply LIVE wire terminal
N- 230VAC mains supply NEUTRAL wire terminal
PE - 230VAC mains supply GROUND wire terminal
1, 2, 3 –relay outputs no 1, 2, 3.
No voltage terminals:
COM - common connection terminal,
1 - wire switch of device number 1
2 - wire switch of device number 2
3- wire switch of device number 3
JP3 shorted
JP3 opened
Device / output channel number :
1
2
3
1
2
3
Stand-by mode
O
O
O
O
O
Remote button or wired switch is pressed for the first time
X
O
X
O
O
Remote button or wired switch is pressed for the second time
X
X
X
X
O
Third …
O
X
X
X
X
Fourth…
O
O
O
X
X
Fifth…
O
O
X
Sixth…
O
O
O
WARNING! Control unit and electric motor connection to 230VAC
mains voltage require personal safety care procedures to be taken
and mains voltage line be OFF at installation. 230VAC supply LIVE
wire must be connected to L terminal and NEUTRAL wire must be
connected to N terminal. Wire control terminals 1, 2, 3 and COM
are logic inputs only and connection of any voltage potential wiring
IS NOT ALLOWED!
elmes
electronic
2 1
COM
N L
NEU T RA L
L I V E
~230V
W1 W2
GR OU ND
3
TRAFO
L3
JP2 JP3 JP1
PRG
LED
PE
L2L1
W3
12
3

Email: [e-mail] Web: www.elmes.pl ©Elmes Electronic 09.2014 - All rights reserved.
Installation hints
The unit includes radio receiver therefore any metal
screening or interference with other electric/radio
equipment operating in close distance should be avoid-
ed as may seriously shorten operating range. In order
to extend operating range a 430 MHz band dipole or
single pole 50Ω antenna may be used with its coaxial
cable screwed to antenna terminals on board of the
receiver in place of the short antenna wire.
PROGRAMMING PROCEDURES
1. Learning transmitters (112 max.) to receiver's
memory:
a) press PRG switch for less than 2 seconds (PRG
LED lights on). Releasing the switch LED continues
to light indicating entering programming procedure,
b) press any remote button - LED sets off,
c) press the same remote button again. Blinking LED
confirms end of procedure.
NOTE! Removing one remote from control unit
memory requires removing all remotes and learning
the remaining ones again.
2. Programming ON/OFF mode with auto set OFF:
a) press control unit PRG switch (LED sets on) for
more than 2 and less than 8 seconds. Release the
switch - LED sets off,
b) press remote button or wired switch once (LED on),
c) after required time has lapsed (max. 4 hours) press
the button or wired switch again (LED sets off),
d) after 2 seconds LED starts blinking several times
confirming end of the procedure.
3. Programming ON/OFF mode only:
a) press PRG switch for more than 2 and less than 8
seconds (LED sets on). Release the switch - LED
sets off,
b) press remote button or wired switch 3 times in short
(less than 2 seconds) intervals,
c) blinking LED confirms end of the procedure.
4. Deleting all transmitters from receiver memory
–perform the procedure in the case of lost or stolen
remote to be eliminated from the control system:
Press and hold down receiver's PRG switch (LED
sets on) for more than 8 seconds, until LED starts
blinking confirming end of the procedure. Receiver’s
memory is cleared of remotes. Programmed on/off
functions remain unchanged.
Learn remotes to receiver according to pt. 1 above.
NOTE! Procedures 2 and 3 above can only be per-
formed with the use of wired switch or a remote learned
to receiver’s memory.
Specification:
Receiver mains supply: 230VAC (2VA).
Relay outputs 1 and 2 rating: 16A/250VAC max.
Relay output 3 rating: 5A/250VAC max.
Auto OFF time: 0.5s up to 4 hours, common for
all three outputs.
Operating tem. range: - 20ᵒC to +55ᵒC.
Case tightness class: IP56
External dimensions (l/w/h) 87/87/39 mm.
DECLARATION OF CONFORMITY
Manufacturer: Elmes Electronic
declares under sole responsibility that its product:
UNIVERSAL CONTROL RECEIVER
Model/type: ST100H-3K
comply with essential requirements of the following directives:
1999/5/EC (R&TTE) Directive,
2004/108/EC (EMC) Directive,
2006/95/EC (LVD) Directive,
and applied harmonized standards, in particular:
EN 60950-1:2006 - electric safety,
EN 61000-6-1:2007 EMC –immunity,
EN 61000-6-3:2007 EMC - emission,
EN 301 489-1 V1.8.1 (2008-04) EMC –radio devices,
EN 301 489-3 V1.4.1 (2002-08) EMC –short range devices,
EN 300 220-1 V2.3.1 (2010-02), EMC –requirements.
Manufacturer:
ELMES ELEKTRONIK, Str. Avicenny 2, 54-611 Wroclaw, Poland
Tel. [phone], fax: [phone]
Signature: ...........................................
Director - Miroslaw Binkowski
Data/Date: 2014-09-30
Manufacturer’s Limited Warranty:
Elmes Electronic remote control sets carry one-year
manufacturer’s warranty as from date of purchase. The
warranty is limited to the replacement of faulty original
parts or repair defects of improper manufacture. Dam-
age, faulty use or improper handling by the user or
installer as well as any changes in product’s hardware
or software caused by the user violets the warranty and
all due repair costs will be charged. Elmes Electronic
shall not be responsible for any damage human or
material caused by its products failure to operate cor-
rectly.
Elmes Electronic reserves the right to change product specification
without prior notice.
KEELOQ
®
is a registered trademark of Microchip Technology Inc.
Elmes Electronic 2007. All rights reserved.
The use of the WEEE symbol indicates that this product may not be
treated as household waste. By ensuring this product is disposed of
correctly you will protect the environment. For more detailed in-
formation about the recycling of this product, please contact your
local authority, your household waste disposal service provider or
the shop where you purchased the product.