Elmo CRA-2 User manual

Wireless Pen Tablet 6X1xxxx01 R0-Xxx
□ Pen
□ Tablet
（CRA-2） （This book ）
□ Quick Start
Guide
CRA-2 Quick Start Guide
● PACKAGE CONTENTS
● USING THE PRODUCT
● DETAILED USAGE OF THE PRODUCT
● PREPARATION
□ Pen holder
□ Wireless
Dongle
□ Extra core x 8
(※Extra cores are
in the pen holder.)
□ USB cable
(For charging or
for connecting to
a device)
● Charging
●接続端子・スイッチを確認する
Side view (left)
Use the supplied wireless dongle to connect the tablet to a device wirelessly.
※ You can also use the tablet by connecting it to a device using the supplied USB cable.
※ Available functions
may dier depending
on the document
camera used.
The tablet will start to
recognize the pen if the
working range is touched
by the pen tip button.
The tablet will enter sleep
mode after about 45
minutes of inactivity.
※ Only when connected
wirelessly
When the pen tip becomes round, replace it with the supplied "extra
core". Use the supplied pen holder when replacing the pen tip.
The Status LED will turn green and go o
after the power is on.
● When connecting wirelessly
⇒The tablet will power on when the
wireless switch is set to on.
● When connecting with the USB cable
⇒ The tablet will power on when it is
connected to a running computer or
document camera.
1. Turn on the power.
2. Operate the tablet
● Replacing the pen tip
● Pen operations
● Storage for the pen and wireless dongle
● Shortcut keys
● Connecting to a device
※ Caution
・When replacing the pen tip, be sure to replace it with the supplied "extra core".
・Make sure that children do not put small parts into their mouths.
Step1.Rotate the pen holder counterclockwise
(arrow ① ) and remove the cover (arrow ② ).
Step2.Put the pen to the center of the pen holder.
Tilt the pen to remove the pen tip.
Step3.Insert the extra core rmly into the pen until
it stops.
Wireless switch Storage for the wireless dongle
Slide and push the dongle into
the storage.Push the dongle
with your nger to take it out.
Pen storage
※ You need to install the EIT on your computer
to use the tablet with your computer. Available
functions may dier depending on the document
camera used.
※ The wireless switch will be
used only when the tablet
is connected wirelessly.
ON（Enabled）
By connecting the wireless dongle to a computer
or document camera, you can use the CRA-2
wirelessly.
OFF（Disabled）
The power enters standby mode.
※ You can use the tablet no matter the wireless
switch is on or o when connecting with the
USB cable.
USB port
Storage for the pen
Insert the pen from the pen tip
into the storage.
Pull the pen with your nger to
take it out.
Storage for
the wireless
dongle
Status LED
Charging: Red
Fully charged: O
①
⑤
②
③
④
Connecting to a computer
You can control your computer like a
mouse. By using with the EIT, you can
add annotations to the screen image.
Insert the wireless
dongle to the USB
port of the computer.
Name Description
①Document
camera mode To display the document camera image.
②Whiteboard
mode To display the whiteboard screen.
③Playback
mode To display images stored.
④Operation/
Settings mode
・When connecting to a computer:
to control a computer as a mouse
・When connecting to the document
camera: to congure pen settings
⑤Close/ Hide
・When connecting to a computer:
to close the EIT
・When connecting to the document
camera: to display or hide menus
Status
LED
①
②
＜ Step1 ＞
Pen holder
Cover
＜ Step2 ＞ ＜ Step3 ＞
Right click
(when using with the document camera
: eraser)
When using with the
document camera
: eraser
Left click
Connecting to the document camera
You can add annotations to the document
camera image or control the document camera.
Insert the wireless dongle to
the USB port of the document
camera.
Working area
Connect the tablet to a computer with
the supplied USB cable.
□ IMPORTANT
SAFEGUARDS
● Checking the connection ports and
switches
For detailed information about the Instruction Manual, refer to the following website:
https://www.elmousa.com/ https://www.elmoeurope.com/index.php/en/

■Read Instructions : All the safety and operating instructions should be read before the appliance is operated.
■Retain Instructions : The safety and operating instructions should be retained for future reference.
■Heed Warnings : All warnings on the product and in the operating instructions should be adhered to.
■Follow Instructions : All operating and use instructions should be followed.
■Cleaning : Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
■Attachments : Do not use attachments not recommended by the product manufacturer as they may cause hazards.
■Water and Moisture : Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool, and the like.
■Placement : Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to
a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer,
or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory
recommended by the manufacturer.
■Ventilation : Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it
from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper
ventilation is provided or the manufacturer’s instructions have been adhered to.
■Power Sources : This product should be operated only from the type of power source indicated on the marking label. If you are not sure of
the type of power supply to your home consult your appliance dealer or local power company. For products intended to operate from battery
power, or other sources, refer to the operating instructions.
■Grounding or Polarization : This product may be equipped with either a polarized 2-wire AC line plug (a plug having one blade wider than the
other) or a 3-wire grounding type plug, a plug having a third (grounding) pin. If the 2-Wire polarized plug will not fit in the outlet, try reversing
the plug. If the plug still fails to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized
plug. The 3-wire grounding type plug will fit into a grounding type power outlet.
This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the grounding type plug.
■Power-Cord Protection : Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon
or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
■Lightning : For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and
power-line surges.
■Overloading : Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric
shock.
■A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause
the product and cart combination to overturn.
■Object and Liquid Entry : Never push objects of any kind into this product through openings as they may touch dangerous voltage points
or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
■Servicing : Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
■Damage Requiring Service : Unplug this product from the wall outlet and refer servicing to qualified service personnel under the
following conditions:
•When the power-supply cord or plug is damaged.
•If liquid has been spilled, or objects have fallen into the product.
•If the product has been exposed to rain or water.
•If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the
operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a
qualified technician to restore the product to its normal operation.
•If the product has been dropped or damaged in any way.
•When the product exhibits a distinct change in performance - this indicates a need for service.
■Replacement Parts : When replacement parts are required, be sure the service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other
hazards.
■Safety Check : Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
■Heat : The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.
■Disposal of battery
This product uses Lithium Ion rechargeable and recyclable battery.
When disposing of the battery, contact the dealer from whom you purchased the product. Do not try to remove the battery by yourself.
■The built-in lithium-ion battery has its own life span. Along with the temperature, frequency of use, time of use and the time passed,
battery capacity decreases gradually.
If operation time becomes substantially short at normal temperature (between 10°C and 30°C), the battery life seems to have come near
its end. Replace it with a new battery. Contact your dealer or ELMO Customer Service for battery replacement (fee applies).
■About electric waves used by the Tablet
The Tablet uses electric waves in the 2.4 GHz band. When using the Tablet, a radio station license is not necessary. However, please note the
following precautions.
Do not use near the following:
・Microwave ovens/industrial, scientific or medical equipment, such as pacemakers
・In-factory radio stations for mobile unit identification systems (radio stations that require a license) used in production lines of factories
・Specified low power radio stations (radio stations that do not require a license)
・IEEE802.11g/b wireless LAN units
When the Tablet is used near any of the equipment mentioned above, electric wave interference may occur, making the Tablet difficult to
use.
■About wireless equipment used in the 2.4 GHz band
This frequency bandwidth is the same as for industrial, scientific, and medical equipment such as microwave ovens, mobile unit
identification systems (radio stations that require a license) used in factory production lines, and specified low-power radio stations (radio
stations that do not require a license).
・Before using this product, check that there are no radio stations for mobile unit identification systems or specified low-power radio stations
nearby.
・If this product emits electric waves which interfere with in-factory radio stations for mobile unit identification systems, cease use
immediately and stop generating the electric waves. For information on countermeasures, etc. (for example, erecting partitions), contact
one of our sales departments whose details are provided at the end of this manual.
・If this product emits electric waves which interfere with specified low-power radio stations used for mobile unit identification systems, or
causes similar problems, contact one of our sales departments whose details are provided at the end of this manual.
https://www.elmousa.com/ https://www.elmoeurope.com/index.php/en/
Declaration of Conformity
ELMO Co., Ltd. hereby declares that this CRA-2 Smartphone is in compliance with the essential requirements and other relevant provisions
of Directive 2014/53/EU.In accordance with Article 10(2) and Article 10(10),This product is allowed to be used in all EU member states.
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est
conforme aux CNR exemptes de licence d'Industrie Canada . Son fonctionnement est soumis aux deux conditions suivantes :
(1) Ce dispositif ne peut causer d'interférences ; et
(2) Ce dispositif doit accepter toute interférence , y compris les interférences qui peuvent causer un mauvais fonctionnement de l'appareil.
Le dispositif a été conçu pour répondre à la demande générale de radioexposition.
BEFORE YOU USE
IMPORTANT SAFEGUARDS
This symbol [crossed-out wheeled bin WEEE Annex IV]
indicates separate collection of waste electrical and
electronic equipment in the EU countries.
Please do not throw the equipment into the domestic
refuse.
Please use the return and collection systems available in
your country for the disposal of this product.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage”within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the product.
SA 1966
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK.DO NOT REMOVE
COVER(OR BACK).
NO USER-SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification or Declaration of this
device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the responsibility of
the user to obtain and use a shielded equipment interface cable with this device. If this equipment has more than one interface
connector, do not leave cables connected to unused interfaces. Changes or modifications not expressly approved by the manufacturer
could void the user’s authority to operate the equipment.
SA 1965
RISK OF
ELECTRIC SHOCK
DO NOT OPEN
CAUTION
FOR UNITED STATES USERS:
INFORMATION
TThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate
the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition
without restriction.
USER-INSTALLER
CAUTION:
Your authority to operate this FCC verified equipment could be voided if you make changes or modifications not expressly approved by
the party responsible for compliance to Part 15 of the FCC rules.