Elnur ADL Series User manual

Please read these instructions carefully before
installing or using this appliance for the first time.
Installation Instructions
ADL
ADL 2012 | ADL 3018 | ADL 4024

Elnur powered by Gabarrón | ADL | Installation Guide 2
• Please read these instructions before installing or
using this appliance for the first time. The warranty
of the storage heater will not cover any damage
caused by non-observance of any of these
instructions.
• This Guide must be kept and given to any new owner
for future references.
• Nothing may be placed within 30cms of the front of
the heater at any time. This is to avoid items coming
into contact with the grille and the head air which
leaves, it. Blocking some or all of this area could
represent a fire hazard. Never use this heater to
dry clothes.
• This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision
or instruction concerning the use of the appliance in
a safe way and understand the hazards involved.
Children must not play with the appliance. Cleaning
and user maintenance must not be undertaken by
children without supervision.
• Children aged from 3 years and less than 8 years
shall only switch on/off the appliance provided that
it has been placed or installed in its intended normal
operating position and they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved. Children aged from 3 years and less than
8 years shall not plug in, regulate and clean the
appliance or perform user maintenance.
• Children of less than 3 years should be kept away
unless continuously supervised. Please check that
the voltage in the rating label fits the power supply.
• Should the heater be moved and reinstalled it is
essential that the work is carried out by a fully
qualified engineer. Before carrying out any work
inside the appliance, the heater must be
disconnected from the electricity supply.
• If during any installation the thermal insulation shows
any sign of damage, it is necessary for the faulty
part to be removed and replaced by an identical part.
• The use of storage heaters is forbidden in any area
where there is a presence of gases, explosives
or inflammable objects.
• The air inlet and outlet grills are provided to ensure
the most efficient operation of the appliance.
They also protect the heater from overheating; therefore,
it is essential that at no time are they covered.
• Surfaces of this appliance could be hot. Children
should be supervised to ensure they do not play
with the heater.
• This heater should be switched off at the isolating
switch before any repair work is carried out.
This action should also be taken during the times
of the year when heat is not required.
• The installation of the heaters must be carried out
in such a way that each pole can be disconnected
from the supply having a contact separation of
at least 3 mm.
• The storage heater should not be installed just below
an electrical socket.
• Ensure that both wall supply switches next to the
heater are turned on. During the summer when no
heat is required, both wall switches can be turned off.
Remember to turn both back when the heat is
required again.
• The appliance must be installed in such a way that
it is impossible for anyone using a bath or shower,
to touch the controls. Never touch the heater with
wet hands.
• The nominal charging time of this storage heater is
indicated on its rating plate and must be controlled
by means of a programmer. Never open a charged
heater.
• The installation must be carried out in accordance
with the current electrical regulations. Check the
voltage on the rating label is the same as the supply.
• This appliance must be earthed.
• After installation a survey of the first charging cycle
should be carried out to ensure that the main input
thermostat switches off. Ventilate the room during
this first cycle.
• The fan may run at any time. This will happen
automatically to maintain the temperature that you
have programmed into the control system.
• To maintain stability, it is essential that the heater is
placed on a level surface and care should be taken
to avoid irregular surfaces, such as carpets or tiled
surrounds partially protruding under the heater.
• The presence in the air of particles of smoke, dust
and other pollutants could, in time, discolour the
walls and surfaces around the heater.
1. WARNING
CAUTION: Some parts of this product can become very hot and cause burns. Particular
attention must be given when children and vulnerable people are present.
!
WARNING: In order to avoid overheating do not cover the heater.

Elnur powered by Gabarrón | ADL | Installation Guide 3
2. INTRODUCTION
Storage heaters are designed to take advantage
of an off-peak tariff.
The heaters consume electricity only during the
off-peak tariff, but due to the highly efficient storage
medium, give you a truly economical 24 hours of
comfort temperatures.
The input control operates a highly sensitive thermostat
which regulates the amount of heat stored.
The discharge takes place when the built-in fan
operates. The fan drives fresh air through the core
and is heated. A bimetallic device mixes the hot air
with fresh air to provide homogeneous temperature.
It is important that the correct rating of heater is installed
to provide the selected level of heat. This will ensure the
best possible running costs against other fuels.
To avoid transport problems, the heater casings and
storage bricks are packed separately. Bricks with some
slight defects in the corners can be used.
You should be aware that storage heaters, when fully
charged, can have high surface temperatures.
3. INSTALLATION INSTRUCTIONS
Installing the controlled storage fan heater:
1. Choose the right place to install the heater,
considering the minimum distances between heater
and other objects. A minimum distance of 50cm is
required for a good heat delivery.
2. Open the box by the side indicated, and remove the
box containing the accessories, electrical elements
and parts to fix to the wall. Turn the box upside down
so the heater stands up on its feet and remove the
shipping carton. Check if it is the requested model
and it is in brand new condition.
3. Screw on the wall the fixing part, making drills at
61 cm above the floor (Fig. 1).
This prevents the heater overturning. The function
of the device is not to hang the heater. If there is any
doubt as to the strength of the wall, please consult
an expert. Storage heaters are very heavy and the
installer must ensure that they are securely fixed
and there is no possibility of them overturning.
4. Remove the front outlet grill by removing the four
screws. Also remove the front panel by removing
the two screws at the bottom of the heater.
5. Attach the LH & RH spacers to the storage heater
using the screws supplied, in the same way as the
screws are fixed in the upper rear section of the
heater side. Check the heater is separated 25mm
from the wall at the top and bottom of the heater
(Fig. 2). Fit and screw the appliance to the anti-tilt
device.
6. Remove the inner front panel.
9
fig. 2
3. INSTALLATION INSTRUCTIONS
Installing the controlled storage fan heater:
1.- Chose the right place to install the heater, considering the
minimum distances between heater and other objects. It is needed
a minimum distance of 50 cm to assure a good heat delivery.
2.- Open the carton box by the indicated side, and remove the box
containing the accessories, electrical elements and parts to fix to
the wall. Turn upside down the box so the heater stands up on its
feet and remove the shipping carton. Check the type is the asked
and it is O.K.
3.- Screw on the wall the fixing part, making drills at 61 cm over de
floor (Fig. 1).
This device prevents the heater overturning when a force of up to
20kg is applied to the upper parts to the exterior. The function of the device is not to hang the heater. If there is any doubt
as to the strength of the wall, please consult an expert. Storage heaters are very heavy and the installer must ensure that
they are securely fixed and there is no possibility of them overturning.
4.- Remove the front outlet grill by removing the four screws. Remove also the front panel by removing the two screws at
the bottom of the heater.
5.- Attach the LH & RH spacers to the storage heater using the screws supplied, in the same way as the screws are fixed in
the upper rear section of the heater side. Check the heater is separated 25mm from the wall at the top and bottom of the
heater (Fig. 2). Fit and screw the appliance to the anti-tilt device.
6.- Remove the inner front panel.
WARNING !
At the other side of this part there is a breakable panel of thermal isolation. It must be handle with care. Avoid touching
it.
fig. 1

Elnur powered by Gabarrón | ADL | Installation Guide 4
7. Place a row of storage bricks carefully, with the
flat side facing the bottom of the heater. Insert
one of the heating elements in the holes in the
right side insulation (Fig. 3).
WARNING: At the other side of this part there is a breakable panel of thermal isolation.
It must be handled with care. Avoid touching it.
!
8. Check that the heating element rests completely
on the bricks without restricting a new row (Fig. 4).
9. Arrange two new rows of bricks, ensuring the flat
side of each bricks is facing towards the bottom
of the heater, and insert a new heating element.
Repeat the operation for the third heating element.
Place the last row of bricks also with the flat side
toward the bottom of the heater. Check there is
no gap between bricks.
10. Connect the heater following the enclosed
diagram. Ensure all connections are correct and
that no connection is damaged. Do not leave any
remaining wire inside the heater.
11. Refit the inner front panel. If the bricks have been
fitted correctly you will find no difficulty during
this action.
9
fig. 2
3. INSTALLATION INSTRUCTIONS
Installing the controlled storage fan heater:
1.- Chose the right place to install the heater, considering the
minimum distances between heater and other objects. It is needed
a minimum distance of 50 cm to assure a good heat delivery.
2.- Open the carton box by the indicated side, and remove the box
containing the accessories, electrical elements and parts to fix to
the wall. Turn upside down the box so the heater stands up on its
feet and remove the shipping carton. Check the type is the asked
and it is O.K.
3.- Screw on the wall the fixing part, making drills at 61 cm over de
floor (Fig. 1).
This device prevents the heater overturning when a force of up to
20kg is applied to the upper parts to the exterior. The function of the device is not to hang the heater. If there is any doubt
as to the strength of the wall, please consult an expert. Storage heaters are very heavy and the installer must ensure that
they are securely fixed and there is no possibility of them overturning.
4.- Remove the front outlet grill by removing the four screws. Remove also the front panel by removing the two screws at
the bottom of the heater.
5.- Attach the LH & RH spacers to the storage heater using the screws supplied, in the same way as the screws are fixed in
the upper rear section of the heater side. Check the heater is separated 25mm from the wall at the top and bottom of the
heater (Fig. 2). Fit and screw the appliance to the anti-tilt device.
6.- Remove the inner front panel.
WARNING !
At the other side of this part there is a breakable panel of thermal isolation. It must be handle with care. Avoid touching
it.
fig. 1
10
7.- Place a row of storage bricks carefully, with the flat side heading the bottom of the heater. Insert one of the heating
elements in the holes in the right side insulation (Fig. 3).
8.- Check that the heating element rests completely on the bricks without restricting a new row (Fig. 4).
9.- Arrange two new rows of bricks, ensuring the flat side of each bricks is facing towards the bottom of the heater, and
insert a new heating element. Repeat the operation for the third heating element. Place the last row of bricks also with the
flat side toward the bottom of the heater. Check there is no gap between bricks.
10.- Connect the heater following the enclosed diagram. Ensure all connections are correct and that no connection is
damaged. Do not leave any remaining wire inside the heater.
11.- Refit the inner front panel. If the bricks have been fitted correctly you will find no difficulty
during this action.
12.- Attach the front panel by hanging it on the “V” in the upper part and securing it at the bottom
with the two screws.
13.- Finally, fit the outlet grill with the four screws.
INSTALATION OF THE WIRELESS AMBIENT THERMOSTAT (OPTIONAL).
- Fix the module to the wall vertically.
- Connect the module following the attached diagram and the color code.
- Do not leave any remaining wire inside the heater.
- The wireless ambient thermostat has its own instructions.
fig. 5
fig. 3 fig. 4
10
7.- Place a row of storage bricks carefully, with the flat side heading the bottom of the heater. Insert one of the heating
elements in the holes in the right side insulation (Fig. 3).
8.- Check that the heating element rests completely on the bricks without restricting a new row (Fig. 4).
9.- Arrange two new rows of bricks, ensuring the flat side of each bricks is facing towards the bottom of the heater, and
insert a new heating element. Repeat the operation for the third heating element. Place the last row of bricks also with the
flat side toward the bottom of the heater. Check there is no gap between bricks.
10.- Connect the heater following the enclosed diagram. Ensure all connections are correct and that no connection is
damaged. Do not leave any remaining wire inside the heater.
11.- Refit the inner front panel. If the bricks have been fitted correctly you will find no difficulty
during this action.
12.- Attach the front panel by hanging it on the “V” in the upper part and securing it at the bottom
with the two screws.
13.- Finally, fit the outlet grill with the four screws.
INSTALATION OF THE WIRELESS AMBIENT THERMOSTAT (OPTIONAL).
- Fix the module to the wall vertically.
- Connect the module following the attached diagram and the color code.
- Do not leave any remaining wire inside the heater.
- The wireless ambient thermostat has its own instructions.
fig. 5
fig. 3 fig. 4

Elnur powered by Gabarrón | ADL | Installation Guide 5
12. Attach the front panel by hanging it on the “V” in
the upper part and securing it at the bottom with
the two screws.
13. Finally, fit the outlet grill with the four screws.
4. USING THE HEATER
The input control allows you to control the amount
of heat stored during the night.
Mild weather it is enough to set the input control at
intermediate positions, you can set the input control
at maximum position if necessary. In this position the
heater stores the maximum energy.
Controlled storage fan heaters deliver their heat from
a highly insulated core by means of a silent fan. This fan
should be managed by a good ambient thermostat.
During the first cycles some odours are possible; in this
case ventilate the room until they disappear.
5. MAINTENANCE OF YOUR STORAGE HEATER
This controlled storage fan heater does not need any
special care.
Dust accumulated on the heater surface can be
removed using a damp cloth when the controlled
storage fan heater is cold. Do not use solvent or
abrasive products.
Night storage heaters are manufactured under an
assured quality system using environment friendly
procedures.
Please take the heaters to a clean point once their
useful life is finished, in order to recycle their materials
in the right way.
6. TECHNICAL SPECIFICATIONS
Model ADL 2012 ADL 3018 ADL 4024
Input 2000W 3000W 4000W
Voltage 220–240V~ 220–240V~ 220–240V~
Max. Charge time 8 h 8 h 8 h
Charge 16 kWh 24 kWh 32 kWh
Weight 123 kg 173 kg 225 kg
Length 63 cm 81 cm 99 cm
Wide 24 cm 24 cm 24 cm
Height 66 cm 66 cm 66 cm
Bricks (7,5 kg) 12 18 24

Elnur powered by Gabarrón | ADL | Installation Guide 6
7. WIRING

Supplier:
ELNUR UK Ltd.
Unit 1, Brown Street North
Leigh, Lancashire, WN7 1BU.
[phone]
[e-mail]
15190020 R2 | EN
Manufactured by:
ELNUR S.A.
Travesía de Villa Esther, 11 28110, Algete
Madrid Telephone: [phone]
© All rights reserved. As part of the continuous improvement
policy, ELNUR, S.A. reserves the right to alter or modify any
specifications without notice.
El símbolo en el producto o en su embalaje indica que este
producto no se puede tratar como desperdicios normales del
hogar. Este producto se debe entregar al punto de recolección
de equipos eléctricos y electrónicos para reciclaje. Al asegurarse
de que este producto se deseche correctamente usted ayudará
a evitar posibles consecuencias negativas para el ambiente
y la salud pública, lo cual podría ocurrir si este producto no
se manipula de forma adecuada. Para obtener información
más detallada sobre el reciclaje de este producto, póngase en
contacto con la administración de su ciudad, con su servicio de
desechos del hogar o con la tienda donde compró el producto.
Estas disposiciones solamente son válidas en los países
miembros de la UE.
The symbol on the product or in its packaging indicates that this
product may not be treated as household waste. Instead it shall
be handed over to the applicable collection point for the recycling
of electrical and electronic equipment. By ensuring this product
is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which
could otherwise be caused by inappropriate waste handling of
this product. For more detailed information about recycling of this
product, please contact your local council office, your household
waste disposal service or the shop where you purchased the
product. These instructions are only valid in the EU member states.
www.elnur.co.uk