Elsema PentaFOB series User manual

ELSEM A
433MHz Keyring Remote with Frequency Hopping – PentaFOB® Series
FOB4 3 3 0 3 W P
433MHz PentaFOB®series Remotes with Frequency Hopping
FEATURES
3-channel PentaFOB®remote
Transmission on 5 different frequencies
Uses frequency hopping spread spectrum (FHSS)
One of the most secure remote controls on the market
Competitive pricing
APPLICATIONS
Keyless access control for automatic gates and roller doors
Warehouse automation i.e. Roller doors, Cooler room doors.…. and anywhere else you need a wireless
signal to transmit a contact closure
DESCRIPTION
The PentaFOB®uses frequency hopping spread spectrum (FHSS), making it impossible for the remote to be
interfered with or jammed. The keyring retainer is moulded as part of the chassis making for a super sturdy
keyring mount.
The PentaFOB® series is an extremely versatile remote control that can be customized through a range of
configurations and colours to suit your needs.
FREQUENCY HOPPING
The PentaFOB®remotes use frequency hopping spread spectrum (FHSS). When a button is pressed, it
simultaneously transmits the code on 5 different frequencies, making it impossible for the remote to be
interfered with or jammed. This allows multiple transmitters to be used in close proximity with no interference
or jamming.
TECHNICAL DATA
Operating Voltage CR2032 Battery
Standb
y
Current 1.8uA
Current Consumption 18mA (t
y
pical) when transmittin
g
Batter
y
life 1.5
y
ears with avera
g
e use
Frequencies 433.100 to 434.700MHz
Operatin
g
ran
g
e up to 120 metres dependin
g
on buildin
g
structure and receiver antenn
a
Operatin
g
Temperature Ran
g
e -5 to 50°C
Decodin
g
S
y
ste
m
Encr
y
pte
d
17
b
illion codes combinations
Dimensions 72 x 43 x 16 mm
Weight 40 grams

ELSEM A
433MHz Keyring Remote with Frequency Hopping – PentaFOB® Series
COMPATIBLE RECEIVERS
Below is a list of compatible receivers for the PentaFOB®remotes.
PCR43301RE
1-Channel Receiver with
Relay Output. Enclosed
in a case
PCR43302P
2-Channel Plug in type
Receiver with Open
Collector Output
PCR43302R
2-Channel Receiver with
Relay Outputs
PCR43302RE
2-Channel Receiver with
Relay Outputs. Enclosed in a
case
PCR43301240R
1-Channel Receiver with
240VAC mains supply
PCR43301240RE
1-Channel Receiver
enclosed in an IP66 case
PCR43302240R
2-Channel Receiver with
240VAC mains supply
PCR43302240RE
2-Channel Receiver enclosed
in an IP66 case
PCR43304R
4-Channel Receiver with
Relay Outputs
PCR43304RE
4-Channel Receiver
enclosed in an IP66 case
PCR43305R
5-Channel Receiver with
Relay Outputs
PCR43305RE
5-Channel Receiver enclosed
in an IP66 case

ELSEM A
433MHz Keyring Remote with Frequency Hopping – PentaFOB® Series
REGULATORY COMPLIANCE STATEMENTS
American Users
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
FCC Notice
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a installation. If this device does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the grantee of this device may void the
user’s authority to operate the equipment.

ELSEM A
433MHz Keyring Remote with Frequency Hopping – PentaFOB® Series
PentaFOB®Programming Instructions
Coding the PentaFOB® remotes and receivers can be done in 2 different ways.
1. Using the Receiver
2. Using another Remote Control
Coding using the Receiver
1. Check that all switches are “OFF” on the receivers 12-way dip switch
2. Press and hold the program button on the receiver
3. Press the remote button for 2 seconds, receiver LED will flash and then turn Green
4. Release the button on the receiver and the remote
5. Press remote control button to test the receiver output
Deleting Receivers Memory
Short the Code Reset pins on the receiver for 10 seconds. This will delete all the remotes from the
receiver’s memory.