Elsys ELT-2 User manual

Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden
E-mail: suppo[email protected] ǀWeb: www.elsys.se
Specifications in this document are subject to change without notice.
©Elektroniksystem i Umeå AB 2020
www.ime.de

2
Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden
E-mail: suppo[email protected] ǀWeb: www.elsys.se
Important safety information
Read this manual before attempting to install the device!
Failure to observe recommendations included in this manual may be
dangerous or cause a violation of the law. The manufacturer, Elektroniksystem i
Umeå AB will not be held responsible for any loss or damage resulting from not
following the instructions of this operating manual.
•The device must not be dismantled or modified in any way.
•The device is not intended to be used as a reference sensor, and
Elektroniksystem i Umeå AB will not be held liable for any damage which
may result from inaccurate readings.
•The battery should be removed from the device if it is not to be used for
an extended period. Otherwise, the battery might leak and damage
the device. Never leave a discharged battery in the battery
compartment.
•The device must never be subjected to shocks or impacts.
•To clean the device, wipe with a soft moistened cloth. Use another soft,
dry cloth to wipe dry. Do not use any detergent or alcohol to clean the
device.
Disposal note in accordance with ElektroG and WEEE Directive
2012/19/EU
The device, as well as all the individual parts, must not be disposed of
with household waste or industrial waste. You are obliged to dispose of the
device at the end of its service life in accordance with the requirements of
ElektroG in order to protect the environment and to reduce waste through
recycling. For additional information and how to carry out disposal, please
contact the certified disposal service providers. The sensors contain a lithium
battery, which must be disposed of separately.
www.ime.de

3
Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden
E-mail: suppo[email protected] ǀWeb: www.elsys.se
Contents
Important safety information.......................................................................................................... 2
Description......................................................................................................................................... 5
Main features of ELT-2 HP........................................................................................................ 6
Installation.......................................................................................................................................... 7
Installing external sensors ......................................................................................................... 8
External temperature sensor................................................................................................ 8
Analog input 0 –3 or 0 –10 Voltage............................................................................... 8
Powered analog input 0 –10V........................................................................................... 9
Switch Input (Pull up) ........................................................................................................... 9
Pulse count (Pull up) ..........................................................................................................10
Pulse count (Pull down) .....................................................................................................10
Pulse count (Pull down) –External pulse.......................................................................11
Pulse count (Pull up) –S0 input ......................................................................................11
4 –20 mA input...................................................................................................................12
Water leak input....................................................................................................................12
Maxbotix distance sensor input.........................................................................................13
Meter (Decagon) sensor input .........................................................................................13
Pulse count (Pull up) –2 channels..................................................................................14
Pulse count (Pull down) –2 channels ............................................................................14
Switch input + Temperature sensor.................................................................................15
Sensor configuration......................................................................................................................16
NFC Configuration.....................................................................................................................16
Over the air configuration ........................................................................................................17
Application parameters.............................................................................................................17
Sensor behavior..............................................................................................................................17
www.ime.de

4
Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden
E-mail: suppo[email protected] ǀWeb: www.elsys.se
NFC Read / Write ......................................................................................................................17
Sensor startup ...........................................................................................................................18
Sampling mode / Periodic measurement .............................................................................19
Schedule Transmission.............................................................................................................19
External sensors ........................................................................................................................20
Specifications ..................................................................................................................................21
Sensor payload format .............................................................................................................21
Regulations......................................................................................................................................22
Legal Notices .............................................................................................................................22
Declaration of conformity ........................................................................................................22
www.ime.de

5
Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden
E-mail: suppo[email protected] ǀWeb: www.elsys.se
Description
ELT-2 is a universal outdoor device for LoRaWAN® wireless network. It is
designed to be in extreme conditions and can measure analog or digital signals.
Use it together with electricity meters, flow meters, analog sensors, moisture
sensors and other external sensors. ELT-2 is enclosed in an IP67 box and have
four internal sensors: temperature sensor, humidity sensor, accelerometer and an
atmospheric pressure sensor. This is a battery-powered device equipped with
NFC (Near Field Communication) and can easily be configured from a
smartphone.
The barcode contains DevEUI and sensor type. This label is located at the back
of your device,
ELT-2-HP
www.ime.de