Elves & Angels Maine User manual

Pre-Assembly Information
• Start by familiarizing yourself with the parts above. This will make it easier to know how it all ts together.
• You will need a Phillips Head Screwdriver and a few drops of glue for the button caps.
• Locate a at, level work surface, like a hardwood oor or a large table.
• Pine is a soft wood, so do not overtighten screws as you can strip out the material. This is less likely to
happen with a screwdriver, so take care when using a drill or screw gun.
• Remember that this product is made of wood, a natural, living material. As such, humidity and dryness in
the air can inuence the product. Though it has been produced with the greatest care and precision
possible you may experience minor variation in t and nish.
• Read instructions completely before beginning so that you fully understand the process. It’s easy and fun
to do, but you’ll feel more condent if you know what the next step is before you get there.
Parts
Caring for the Doll house
• The Doll house is made of natural wood that has been nished with Tried & True Danish Oil, a polymer-
ized linseed oil, which is food safe and non-toxic. To maintain the satin nish, we recommend reapplying
this oil periodically, as you notice the wood drying out. Please visit http://www.triedandtruewoodnish.
com to nd a retailer.
• Should the wood become discolored, we recommend cleaning it with Murphy’s Oil Soap. If stubborn stains
persist, use a ne green scrubbie (such as used on pots and pans) and rub lightly following the grain of the
wood. Then apply a thin coat of the Danish Oil, according to the instructions provided.
Maine Doll house Assembly Instructions

Doll house Assembly
1. Position First Floor into the bottom groove of the
Side Wall, rounded edge towards center,1” from the
edge using Spacer #1 as a ruler.
2. Repeat step one with other Side Wall and First
Floor, ensuring the rounded edge is centered in the
Side Wall. Secure with two Wood Screws.
3. Slide second First Floor into Side Wall grooves
with rounded edge toward the center, ush against
opposite First Floor Secure with two wood screws
4. Slide Second Floor into top grooves of Side Walls
ensuring each end is set in the length of Spacer #2.
Secure either end with two Wood Screws.
5
Page 2 of 4
5. On a at surface Place each Small Partition into
the grooves of the Long Partition, ensuring the bot-
toms are ush. Secure each Small Partition with two
Wood Screws. Drive Wood Screws into Top Backing
7. Align each Small Parti-
tion using Spacer #4 and
secure between Side
Walls And Small Partition
as shown. Secure with
two Wood Screws each.
6. Align Partition assembly in middle of First Floors
and using Spacer #3 between Side Walls and end of
partition assembly. Secure Long Partition with two
Wood Screws through pre-drilled holes underneath
First Floors.
5

Page 3 of 4
8.Place Second Floor Wall against Second Floor
ensuring bottom edges are ush. Secure with two
Wood Screws.
11. Repeat step 10 for remaining three corners.
8. Secure opposite Second Floor Wall to other side
of Second Floor as in step 8 using two Wood Screws.
10. Align False Beam angled end with edge of Side
Wall and False Beam Bottom with upper of edge
Side Wall top groove. Secure with two Wood Screws.
9. Center Top Doorway with pre-drilled holes in
middle of Second Floor Walls and secure with two
Wood Screws.
12. Center Gable End on top of Side Wall ensuring
side of Gable End and Sided Wall are ush. Secure
with four Wood Screws.
13. Repeat step 12 to attach opposite Gable End to
Side Wall.
14. Place Back Roof into Front Roof groove ensuring
ends are ush. Place assembly onto Gable Ends en-
suring Gable Ends set into Roof assembly grooves.

Page 4 of 4
18. Attach First Floor Wall to First Floor with rounded
edge towards the middle and bottom edge ush
with bottom edge of First Floor. Secure with two
Wood Screws.
19. Repeat step 18 for remaining three First Floor
Walls.
20. Place a drop of white glue into each of the pre-
drilled screw holes and insert a Button Cap. Tap
lightly with a hammer to fully seat if needed.
Congratulations on a Job Well Done! We Hope You and Your Child Enjoy Years of Play with Your
Maine Doll house!
15. Secure Roof Assembly to Gable Ends with eight
Wood Screws.
16. Orient Roof End as shown on remaining edge of
Gable End and False Beam. Secure using two Wood
Screws.
17. Attach remaining three Roof Ends oriented as in
step 17 securing with two Wood Screws each.