emaux RGB-CB User manual

1
4
PART LIST
CONTROL BOX INSTALLATION DIAGRAM
SPECIFICATIONS
Work temperature
Input voltage
Output voltage
0-35℃
AC220-240V, 50Hz
AC 12V, 2*300W
Frequency RF 433.92MHz
M5×35 Self-
Tapping Screw
M5×35
Control Box Plastic Fitting
Wall
RGB SERIES UNDERWATER LIGHT
CONTROL BOX
Model: RGB-CB
Code:08040009(220-240V 50Hz) 08040020(110V 60Hz)
Keep this manual safe for future reference
APPLICABLE FOR EMAUX RGB SERIES UNDERWATER
LIGHT:
RGB-P100/RGB-TP100/RGB-NS75/RGB-NS150/RGB-H200
Warning:
This electrical control box must be installed by a licensed or certified electrician or a
qualified serviceman in accordance to the requirements of your government
standard or local authorities. Improper installation will create electric hazards which
could result in serious injury, death as well as damage to the property.
CUT THE POWER BEFORE SERVICE AND MAINTAINANCE!
INSTALLATION EXPLAIN
1.Remove the Panel from the Control Box, position the box to the desired fitting
place and mark on the wall with the location of the drilled holes, then drill 4 holes
of ø8mm on the marked position and insert a plastic fitting, secure the box by
fastening 4 screws of M5x35 to the plastic fittings(See diagram below).
AC110V,60Hz
Key
No.
Part No.
Description
Qty
1
03011007
M4*12 Screw
4
2
04014054
Light Switch
1
3
04014090
Electronic Board (220V 50Hz/60Hz)
1
3
04014114
Electronic Board (110V 60Hz)
1
4
03011196
M3*6 Screw
4
5
89480101
Control Box
1
6
04014013
Cable Gland
3
7
87013019
Plastic Wall Fitting for Screw
4
7
03011023
M5*35 Screw
4
8
04014089
Remote Control with Battery
1
9
01360015
Panel board
1
EMAUX (Zhong Shan) Swimming Pool Equipment Co., Ltd.
Address: Long Zhu Industrial Park, Nan Lang Industrial Area, Nan Lang Town, Zhong Shan City, Guangdong Province, China

3
2
CONTROL BOX WIRING DIAGRAM
Warning: load of the control box should not exceed 2*300W.
!
CONTROLS INDEX
Sync button
Frequency Setting
Each control box is associated with a remote control. To use a single remote to
control a multiple number of control boxes, you would need to configure the
Frequency at the back of the remote control. The Frequency of the Remote would
then need to be synced with all the control boxes.
!Slide open the back of Remote Control
!Set the Frequency
!Turn on Control Box(es)
!Sync the Remote to the Control Box(es)
!Press the Sync Button until the lights on the Control Boxes turn on
If you have multiple control boxes and you want to use a remote control for a
specific control box, you must set the Frequency on the remote control to a unique
combination.
!Slide open the back of Remote Control
!Set a unique Frequency on the Remote Control
!Turn on the Control Box associated with that particular Remote Control
!Sync the Remote to the Control Box
!Press the Sync Button until the lights on the Control Box turn on
!Once synced, turn off the control box and move to the next set of Control Box
and Remote. Repeat above steps.
Setting of the Remote Control
Operation distance for the remote control is 25m.
25m
Contr ol box
Control box
!Switch on the “POWER” switch to turn on themain power, the POWER LED will light
up.
!Press the “POOL” button to switch ON/OFF or change color for all the underwater
lights connected to the POOL outlet.
!Press the “SPA” button to switch ON/OFF or change color for all the underwater
lights connected to the SPA outlet.
!Press the “POOL & SPA” button to switch ON/OFF or change color for all the
underwater lights connected to both POOL and SPA outlet (Remark: To sync the
underwater lights connected to the POOL and SPA outlet, press the “RESET”
button).
!Press the “RESET” button to reset all the underwater lights connected to the POOL
and SPA outlet, to white color.
PATTERN TABLE
No.
PATTERNS
No.
PATTERNS
1
Static white
6
Static yellow
2
Static blue
7
Three-color change
3
Static green
8
Seven-color change
4
Static cyan
9
Seven-color gradual change (Fast)
5
Static purple
10
Seven-color gradual change (Slow)
220~240V(110V)
220~240V(110V)
(AC110V)
INPUT: