Emergi-Lite Prestige Economizer Series User manual

Emergi-Lite Tel: [phone] Fax: [phone] www.emergi-lite.com 07/09 750.1357 Rev. D
1/2
Prestige Economizer Series - Edge-Lit Led Exits
Prestige Economizer Series - Edge-Lit Led Exits
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always
be followed including the following:
READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
1. Do not use outdoors.
2. Do not let power supply cords touch hot surfaces.
3. Do not mount near gas or electric heaters.
4. Use caution when handling batteries. Avoid possible shorting.
5. Equipment should be mounted in locations and at heights where it will
not readily be subjected to tampering by unauthorized personnel.
6. The use of accessory equipment not recommended by the manufac-
turer may cause an unsafe condition.
7. Do not use this equipment for other than intended use.
8. All servicing should be performed by qualified service personnel.
SAVE THESEINSTRUCTIONS
Installation Instructions
1. Turn off AC power.
2. Route AC unswitched circuit of rated voltage into junction box and
leave 6” of wire length.
3. Follow directions on the panel for chevron placement. (Note: for sin-
gle sided units with clear background place chevron on back of the
panel).
4. Unsnap cover (12) by using your fingers, lift the bottom of the cover
and remove (if the cover is to difficult to open gently pry the cover
using a flat head screw-driver at the point indicated in fig.1).
Wall Mount (See Figure 1)
a. Extend the AC supply leads with the extension wires supplied (fol-
low the electrical wiring in figure 4).
b. Feed the supplied wires through the center hole of the spider plate
then attach it to the junction box.
c. Feed the supplied wires through the center hole of the canopy
then attach it to the spider plate using the screws provided (6).
d. Remove the knock out towards the inside with a screwdriver. Feed
the supplied wires through the center hole and mount the housing
to the canopy with the screws provided (4).
Ceiling or End mount (See Figure 2 & 3)
a. For ceiling mount: remove plugs (see figure 2)
a. For end-mount: remove the knock outs on the end cap towards
the inside with a screwdriver (see figure 3).
b. Fasten the canopy to the housing using screws(4) and lock nuts
provided (9).
Figure 1
1
2
3
5
6
7
8
10
11
12
4
Pry here
Part List
1. Junction box (existing)
2. Spider Plate
3. Junction box screws (not
supplied)
4. Canopy screws - long(2)
5. Canopy
6. Canopy screws - short(2)
7. Housing
8. End cap screws
9. Lock Nuts
10. Panel holder plugs
11. Panel
12. Cover

Prestige Economizer Series - Edge-Lit Led Exits
2/2
Emergi-Lite Tel: [phone] Fax: [phone] www.emergi-lite.com 07/09 750.1357 Rev. D
c. Extend the AC supply leads with the extension wires supplied
(follow the electrical wiring in Figure 4).
d. Route the supplied wires through the center hole of the spider
plate.
e. Fasten the spider plate to the junction box using the junction box
screws(3).
f. Feed wires into the unit through the center hole of canopy.
g. Fasten the canopy-housing assembly to the spider plate using
the screws provided(6).
5. For remote power DC units, connect the red wire to the positive of the
DC supply and the blue to the negative (6 to 24VDC).
6. Make the proper connections, our system accepts an input voltage of
120 to 277 VAC (see figure. 4). Connect the purple and white leads to
the building utility. Connect the green ground wire to the service
ground or the ground connection in the junction box.
7. AC/DC or AC only models: When AC is energized the LED strip will
light.
For self-powered models only
a. When ready to energize AC, plug in battery connector to circuit
board. Connect battery and turn on AC power within 6 hours.
b. When AC is energized the LED strip will light and green pilot light
will illuminate. Allow 24 hours charge before initial duration test-
ing.
8. Replace cover by squeezing it a little bit and pushing down. Secure
the cover with the appropriate screws(8).
9. Reconnect the AC power.
Testing (self-powered models only)
Operate test switch: Press switch-”AC on” pilot light will turn off
- Release switch- “AC on” pilot will turn on
- Legend remains lit during testing.
Maintenance
None required. Unit should be tested monthly in accordance with safety
codes and local codes. If AC supply to the unit is to be disconnected for
2 months or more, the battery must be disconnected.
1
2
3
4
5
6
9
8
10
11
12
7
Figure 2
Plugs
1
2
3
4
5
6
7
9
10
11
12
8
Figure 3
Knockout
White- neutral
Red DC+
Blue DC-
Canopy
Battery*
(self-powered only)*
LED strip
DC supply
(AC/DC
Figure 4
Switch*
AC on (pilot)*
Purple-AC 120 to 277VAC
Green- ground
{
AC supply leads }(6 to24v DC)
models only)
Note:
Final connections
are to be made inside
unit using extension
wires provided.