Emerson Bettis WO User manual

Installation, Operation and Maintenance Manual
MAN-02-10-92-0705-EN Rev. 0
March 2019
WO & WB AWWA Gears & MG Power Gears
Instruction & Maintenance Manual

Installation, Operation and Maintenance Manual
MAN-02-10-92-0705-EN Rev. 0
Table of Contents
March 2019
I
Table of Contents
Table of Contents
Section 1: Purpose
Section 2: Lubrication
2.1 Lubrication Grease Specication .................................................................... 2
Section 3: Installation Procedure
3.1 General Instructions....................................................................................... 3
3.2 Stop Setting Procedure .................................................................................. 3
Section 4: Disassembly Instructions
4.1 Instructions - WO & WB AWWA Gears ............................................................ 4
4.2 Instructions - GB1 Spur Gear Attachment....................................................... 6
4.3 Instructions - GB3 Spur Gear Attachment....................................................... 7
4.4 Instructions - MG Quarter Turn Power Assemblies .......................................... 8
Appendix A: Reference Drawings

March 2019
Installation, Operation and Maintenance Manual
MAN-02-10-92-0705-EN Rev. 0
1
Section 1: Lubrication
Lubrication
Section 1: Purpose
This instruction and maintenance manual replaces document W291 and explains how to
install, operate, and maintain the WO, WB & MG Gears.
WARNING:
Read this manual in its entirely before installing, operating, or performing maintenance on
the WO, WB & MG Gears.
Use caution when working on, with, or around valves and actuators.
High pressures, forces, voltages, and ammable media can be present.
Failure to follow instructions for proper electrical wiring, storage, setup and maintenance
may cause serious injury, damage equipment, or void warranty.
Installation, Operation and Maintenance should only be performed by qualied personnel.

Installation, Operation and Maintenance Manual
MAN-02-10-92-0705-EN Rev. 0 March 2019
2
Section 2: Installation Procedure
Installation Procedure
Section 2: Lubrication
2.1 Lubrication Grease Specication
Extreme pressure multipurpose grease, NLGI Grade EP-0, suitable for bronze
gear assemblies.
Inspection Procedure:
1. Ensure the worm is immersed in lubricant. Lubrication should be checked periodically
to determine its condition.
2. Examine the lubricant for containments such as dirt or water. Should contamination
be present, remove the grease and ush with a commercial degreaser, solvant such
as mineral spirits (or white spirits), which is non-corrosive and does not affect seal
materials. Rell with fresh lubricant.
3. Examine the lubricant for consistency. The appearance should be slightly uid.
NOTE:
Alternate lubricants may be substituted in place of the standard that is supplied by the
factory only if they are equivalent. Do not add different lubricants to the operator unless
approval has been obtained from the lubricant manufacturer.

March 2019
Installation, Operation and Maintenance Manual
MAN-02-10-92-0705-EN Rev. 0
3
Section 3: Disassembly Instructions
Disassembly Instructions
Section 3: Installation Procedure
3.1 General Instructions
Refer to Figure 1.
1. Place valve in full closed position.
2. Install splined bushing (17) on valve shaft (and key). Tighten set screw (20) to secure
bushing to shaft.
3. Turn input shaft, rotate actuator drive sleeve (19) to full closed position. Indicator will
point to close. Mechanical stops should be preset for 90° of travel. If not, adjust at this
time. See disassembly instructions for adjustment procedure.
4. Remove dial indicator (16) to facilitate mounting to valve.
Note: WB units have no dial indicator.
5. Lower actuator on to splined shaft. Actuator is now ready for attachment to valve.
6. Once in place on valve, re-install indicator cover (16).
3.2 Stop Setting Procedure
1. With actuator and valve in full closed position, remove stop screw cover bolt (12).
2. Remove jam screw (13).
3. Adjust stop screw (14) inward if valve is closed and the stop has not been engaged.
If valve is not fully closed, adjust the stop screw outward so the valve can be moved
to the full closed position. Once the valve is in full closed position, adjust the screw
inward until the screw touches the worm segment. Once the screw is in contact
(with valve fully closed), adjust outward 1 /2 turn.
4. Once the stop screw is set, install the jam screw (13) and tighten until secure.
Reinstall stop screw cover bolt (12).
5. Move the valve to the full open position and repeat the procedure for the open stop.

Installation, Operation and Maintenance Manual
MAN-02-10-92-0705-EN Rev. 0 March 2019
4
Section 3: Disassembly Instructions
Disassembly Instructions
Section 4: Disassembly Instructions
4.1 Instructions - WO & WB AWWA Gears
Refer to Figure 1.
1. Remove hex head cap screws (12) and seal washers (15).
2. Remove jam screws (13).
3. Remove stop screws (14) from main housing.
4. Rotate handwheel shaft clockwise until pointer cap (16) stops rotating or until
handwheel shaft can no longer be turned.
5. Remove dial indicator (16) and housing cover (3). Note: WB units have no dial
indicator (16).
6. Remove closed cap (1) and open cap (24).
7. Remove thrust bearing cups (2) from main housing. By rotating worm shaft (18)
in both directions.
8. Pull worm shaft (18) from main housing (4). Caution: Note the assembly
position of the worm shaft for accurate reassembly. Do not remove bearings
from the worm shaft.
9. Once the worm is clear, remove the two thrust bearing cones (5).
10. Remove drive sleeve (19) lifting upward from main housing. Caution: Note
position of drive sleeve in main housing to ensure accurate reassembly. Remesh
gearing during reassembly.
11. Check the condition of all gaskets and o-rings. If torn or damaged, replace.
12. Reassemble the actuator by reverse order of the steps listed above. The end cap
gasket thickness is generally 1 /32" to 1 /64 ° . This is determined by the amount
of axial oat in the worm shaft once the bolts on both the end caps (1 & 24)
have been tightened. When properly adjusted, axial oat should be almost
eliminated, while still allowing the worm shaft to be easily rotated by hand (larger
WO/WB units require a handwheel or T-bar to rotate input shaft even under no
load conditions).
13. Preset mechanical stops for 90° of rotation by moving the drive sleeve (worm gear)
to its approximate center point (mid travel). From this midpoint, estimate 45 ° travel
in the open direction. Insert stop screw (14) and adjust accordingly. Repeat this step
for the closed direction (90° from open or 45° from center). Before reinstallation of
the housing cover (3), ll the housing with recommended lubrication (Texaco EP-0 or
equal) to approximately 3/4 full (check that worm shaft and bearings are covered).
Refer to lubrication instructions for additional details.
Once the actuator is installed on the valve, it will be necessary to nal adjust the stop
screws to suit the actual valve movement required. (Refer to installation procedure,
stop setting).

March 2019
Installation, Operation and Maintenance Manual
MAN-02-10-92-0705-EN Rev. 0
5
Section 3: Disassembly Instructions
Disassembly Instructions
Figure 1 Assembly WO20 67:1 6.50" (DWG 84216 Rev. F)
on 6.500" Bolt Circle Straddle C
torque wrench tightening.
2) Actuator mounting holes are (4) 3/4-10 UNC-2B
3) Most Screws may be reused and retightened to
handwheel wrench tight. Item 10 should not be reused.
Tighten to torque (+/- 5%) shown for specific screw.
Screw threads should be clean & lightly oiled prior to
1) Customer furnished mounting screws should be
Grade 5 or stronger 3/4-10 UNC with length selected
to engage .75" minimum to 1.00" maximum into
actuator mounting flange. Torque 250 ft-lb
CI01
17
ERO 14963
Drawing
24
25
22
23
CI03
S01
R001
SE01
20
21
19
18
SO12
S22/6
BR03
S005
Assembly
G003
6
S10/3
14
15
16
12
13
S22/10
SE05
CI01
S11/10SS
S19/10
9
10
11
7
8
SE09
S11/6SS
G003
SE01
3
5
4
2
1
CI01
B002
CI03
B002
CI03
Assembly Notes:
E
P
O
N
S
C
O
L
L
.
(+/- 5%).
SE01
27
31366-1
Part No.
have been used. See Table for replacement parts.
Variable: 1, 2 or 4 of the thickness' referenced may
31366-2
Thickness
1/32 (.031)
1/64 (.015)
1/32 (.031)
1/64 (.015)
13466-2
13466-1
CvrCap HsgEnd
Gskt Gskt
PL01
31
NUMBER
LHE/CL
DWN REVISED DATEORIG DATE APRD
1/7/98 7/29/02
DESCRIPTION
PAGE REV
input for CW rotation of valve shaft. Special applications require Counter Clockwise (CCW)
Special Note: Industry standards for actuators generally require Clockwise (CW) rotation of handwheel to Close
valve with Clockwise (CW) rotation of valve shaft. EIM Model WO20-B has CW rotation of actuator
rotation of EIM input, therefore, model WO20-A is made available for these non-standard requirements.
35477-1 SPLINE BUSH
67:1R WORM (H/W)
DI OPEN CAP
RTN 5100-125
NAMEPLATE
WO20-A 67:1 6.50"
O-RNG 568-326-70D
KEY .25 SQ X 1.50
SHSS 3/8-16 X .50
67:1 RH DR/SLV
84216-A
1
1
1
1
1
1
1
1
4045232617
4060001125
35333-1
36664
35689-2R
4101802514
4042209310
34971-4R
(CCW for CW)
3
7
18
724
21 10
DI END CAP
DESCRIPTION
WO20-B 67:1 6.50"
SHSS 5/8 X 2.0
SHJS 5/8-11 X .31
HHCS 3/8-16 X 1.00 SS
O-RNG 568-250-70D
O-RNG 568-252-70D
THRUST BRG CONE
1/4T MAIN HOUSING
STAT-O-SEAL .625
HHCS 5/8-11 X 1.0 SS
THWS 10-24 X .48 SS
END CAP GASKET
HSG CVR GASKET
HOUSING COVER
THRUST BRG CUP
INDICATOR
13466-
2
6
2
2
2
24
1
*
1
1
4042250003
4042533120
4045611615
4042214410
36736
4042533048
4045225017
4045225217
34094
31366-
QTY
2
2
1
1
1
84216-B
ITEM CODE
4000500132
4000500131
36665
34978
35333
PART NUMBER
(CW for CW)
19
22
17
23
14
4
13
10
16.5 ft-lb
16.5 ft-lb
1
5
2
16
25
11
11
10
12 15
16.5 ft-lb
O-RNG 568-047-70D
40452047171
*
*
*
*
30006008701 1/8-27 NPT SQ. HD. PLUG SS
WO20 67:1 6.50"
1 of 1 F84216-
10
1
3
16
19
8
11
6
12
18
9
17
20
4
15
27
10
31
Table 1. (DWG 84216 Rev. F)
Items Description QTY. Items Description QTY.
1 Closed Cap 1 14 Stop Screw 2
2 Thrust Bearing Cup 2 15 Sealing Washer 2
3 Housing Cover 1 16 Dial Indicator 1
4 1/4 T Main HSG 1 17 Spline Bushing 1
5 Thrust Bearing Cone 2 18 Worm Shaft 1
6 HSG CVR Gasket 1 19 Drive Sleeve 1
7 End Cap Gasket 1 20 Set Screw 1
8 O-Ring 1 21 Key 1
9 O-Ring 1 22 Retaining Ring 1
10 End Cap Bolts 16 23 O-Ring 1
11 Dial Indicator Bolts 4 24 Open Cap 1
12 Stop Screw Cover Bolts 2 25 Nameplate 1
13 Jam Screw 2 26 HSG CVR Bolts 8

Installation, Operation and Maintenance Manual
MAN-02-10-92-0705-EN Rev. 0 March 2019
6
Section 3: Disassembly Instructions
Disassembly Instructions
4.2 Instructions - GB1 Spur Gear Attachment
1. Remove retaining ring (32), allowing the removal of handwheel and key (33) from
input shaft (30).
2. Remove eight GB1 cover bolts (29), housing cover (27) and gasket (24).
3. Remove input shaft (30). If damaged or bent, replace. Check bronze bearings
(25) & (22) for wear. Replace if needed.
4. Remove retaining ring (28). If damaged or bent, replace.
5. Remove gear (31) from worm shaft (18).
6. Remove eight socket head cap screws (34).
7. Remove GB1 housing (21) and end cap gasket (7).
8. Inspect bearing (22). If worn or damaged, replace.
9. Inspect all gaskets and a-rings. If worn or damaged, replace.
To reassemble, proceed in reverse order listed above.
Figure 2 WG54 320:1 11.75" (DWG 83839 Rev. D)

March 2019
Installation, Operation and Maintenance Manual
MAN-02-10-92-0705-EN Rev. 0
7
Section 3: Disassembly Instructions
Disassembly Instructions
4.3 Instructions - GB3 Spur Gear Attachment
1. Remove retaining ring (34), allowing the removal of handwheel and key (32) from
input shaft (33). Note: Key (33) not used for tandem mount GB 1 /G83. Input shaft
(33) is splined.
2. Remove twelve GB3 cover bolts (38), housing cover (28) and gasket (39).
3. Remove input shaft (33).
4. Remove gear (24).
5. Remove retaining ring (37).
6. Remove gear (27) from worm shaft.
7. Inspect bearings (31, 36, 26). If worn or damaged, replace.
8. Remove four cap screws (40) and GB3 housing (23)
9. Remove eight cap screws (7), G83 adaptor (2) and end cap gasket (16).
10. Inspect all gaskets and o-rings. If damanged or worn, replace.
To reassemble, proceed in reverse order listed above.
Figure 3 Assembly WG65 972:1 16" (DWG 83841 Rev. C)

Installation, Operation and Maintenance Manual
MAN-02-10-92-0705-EN Rev. 0 March 2019
8
Section 3: Disassembly Instructions
Disassembly Instructions
4.4 Instructions - MG Quarter Turn Power Assemblies
1. Separate "M" electric unit (DWG 83775) from MG Power Assembly by removing bolts
(23) and pulling the two assemblies apart.
2. Remove bolts (22) and M/MG Adaptor (8).
3. For further disassembly of MG Power Assembly, refer to the section "DISASSEMBLY
INSTRUCTIONS, WO & WB AWWA GEARS". For parts listings, refer to the specic
assembly drawing for that model.
4. For disassembly of "M" Power Assembly, refer to 1/M Manual E987 and Assembly
Drawing 83775.
Figure 4 Assembly MG03 1/4T PWR ASSY (DWG 84360_F)

March 2019
Installation, Operation and Maintenance Manual
MAN-02-10-92-0705-EN Rev. 0
9
Appendix
Appendix
Appendix: A Reference Drawings
on 6.500" Bolt Circle Straddle C
torque wrench tightening.
2) Actuator mounting holes are (4) 3/4-10 UNC-2B
3) Most Screws may be reused and retightened to
handwheel wrench tight. Item 10 should not be reused.
Tighten to torque (+/- 5%) shown for specific screw.
Screw threads should be clean & lightly oiled prior to
1) Customer furnished mounting screws should be
Grade 5 or stronger 3/4-10 UNC with length selected
to engage .75" minimum to 1.00" maximum into
actuator mounting flange. Torque 250 ft-lb
CI01
17
ERO 14963
Drawing
24
25
22
23
CI03
S01
R001
SE01
20
21
19
18
SO12
S22/6
BR03
S005
Assembly
G003
6
S10/3
14
15
16
12
13
S22/10
SE05
CI01
S11/10SS
S19/10
9
10
11
7
8
SE09
S11/6SS
G003
SE01
3
5
4
2
1
CI01
B002
CI03
B002
CI03
Assembly Notes:
E
P
O
N
S
C
O
L
L
.
(+/- 5%).
SE01
27
31366-1
Part No.
have been used. See Table for replacement parts.
Variable: 1, 2 or 4 of the thickness' referenced may
31366-2
Thickness
1/32 (.031)
1/64 (.015)
1/32 (.031)
1/64 (.015)
13466-2
13466-1
CvrCap HsgEnd
Gskt Gskt
PL01
31
NUMBER
LHE/CL
DWN REVISED DATEORIG DATE APRD
1/7/98 7/29/02
DESCRIPTION
PAGE REV
input for CW rotation of valve shaft. Special applications require Counter Clockwise (CCW)
Special Note: Industry standards for actuators generally require Clockwise (CW) rotation of handwheel to Close
valve with Clockwise (CW) rotation of valve shaft. EIM Model WO20-B has CW rotation of actuator
rotation of EIM input, therefore, model WO20-A is made available for these non-standard requirements.
35477-1 SPLINE BUSH
67:1R WORM (H/W)
DI OPEN CAP
RTN 5100-125
NAMEPLATE
WO20-A 67:1 6.50"
O-RNG 568-326-70D
KEY .25 SQ X 1.50
SHSS 3/8-16 X .50
67:1 RH DR/SLV
84216-A
1
1
1
1
1
1
1
1
4045232617
4060001125
35333-1
36664
35689-2R
4101802514
4042209310
34971-4R
(CCW for CW)
3
7
18
724
21 10
DI END CAP
DESCRIPTION
WO20-B 67:1 6.50"
SHSS 5/8 X 2.0
SHJS 5/8-11 X .31
HHCS 3/8-16 X 1.00 SS
O-RNG 568-250-70D
O-RNG 568-252-70D
THRUST BRG CONE
1/4T MAIN HOUSING
STAT-O-SEAL .625
HHCS 5/8-11 X 1.0 SS
THWS 10-24 X .48 SS
END CAP GASKET
HSG CVR GASKET
HOUSING COVER
THRUST BRG CUP
INDICATOR
13466-
2
6
2
2
2
24
1
*
1
1
4042250003
4042533120
4045611615
4042214410
36736
4042533048
4045225017
4045225217
34094
31366-
QTY
2
2
1
1
1
84216-B
ITEM CODE
4000500132
4000500131
36665
34978
35333
PART NUMBER
(CW for CW)
19
22
17
23
14
4
13
10
16.5 ft-lb
16.5 ft-lb
1
5
2
16
25
11
11
10
12 15
16.5 ft-lb
O-RNG 568-047-70D
40452047171
*
*
*
*
30006008701 1/8-27 NPT SQ. HD. PLUG SS
WO20 67:1 6.50"
1 of 1
F84216-
10
1
3
16
19
8
11
6
12
18
9
17
20
4
15
27
10
31

Installation, Operation and Maintenance Manual
MAN-02-10-92-0705-EN Rev. 0 March 2019
10
Appendix
Appendix
2) Code is Material Description and is not required for ordering of spare or maintenance parts.
Refer to EIM JOB SPEC SHEET for specific parts for each actuator serial number.
H/W GEAR PARTS MTR GEAR RTN ASSY
MTR GEAR MTR GEAR MTR GEAR MTR GEAR
Description
Assembly
Drawing
1) Variable Parts:
*
Notes:
Item
V4 V8
M1 M2 M3 M4 1
1 1
SO15 SO15 SO15
1 1 1
Qty
CB10 CB15 SO15
Code
- - - P3460- 83638- -
Part No.
*
O-RNG 568-228-70D 2" NPT Plug (Iron) RTN 5108-59 SS
HHWLCS 1/4-20 X .75
CLUTCH SHAFT ASSY THRUST/BRG CUP THRUST/BRG CONE
TORQUE SPG PARTS
MOUNTING BASE
HANDWHEEL ASSY
H/W SHAFT ASSY FLANGED BEARING HHCS 3/8-16 x 2.0 SS HHCS 3/8-16 x 1.25 SS
MOTOR ASSEMBLY
HHC-N-S 3/8-16 X 1.0
MCP ELECTRIC CVR MCP BASE ASSY
SHSS 3/8-16 x 1/2
M/MG GEAR
O-RNG 568-050-70D
*
83768-
CB08
1
76
1 4
99 81
P3803- 35890
CB09 CB17
*
1 1 1 1 2 2 1 1 1 1 1 1 2 2 1 1 1 1
47
66 75 62 65 50 57 56 49 45 44 43 42 34 41 36 33 31
4042520012
S12/4
38548 4060012059 4042533052 4042533049 4042209315 35820- 4045205017
S11/6S S11/6S CB08 S22/6
83741
R002 BR09 CI01 SE01
*
*
4000500113 4000500114 P3439- 35589-1 83787- 83422 35009 4045222817
CB07 CB06 B002 B002
83631
CB05 CB04 BR06 CI03 SE01
*
*
HHCS 3/8-16 x 1.25 SS 56 CLUTCH CAM
Description
HHWLCS 1/4-20 x 1.00
O-RNG 568-154-70D
WORM ASSEMBLY
O-RNG 568-228-70D O-RNG 568-021-70D O-RNG 568-128-70D TQ LIMIT GEAR ASSY
G/L PINION ASSY
O-RNG 568-163-70D TORQUE SPRING CVR FHSCS 3/8-16 x .75 PLUG 1/2 NPT MAIN HOUSING O-RNG 5-642-70D P/S CLUTCH ASSY THWS 10-24 X .48 RTN 5100-59
4060001059
R001
4
3
4 1 3 1 1 1 2 2 1 1 1 1 4 3 1 1 1 4
22 29 25 24 23 20 18 17 15
8
10 11 12
9 7 6 5 4
4042520020 4045215417 P3643- 4045222817 4045202117 4045212817 83729 83730 or -1 4045216317
SE01 S12/4 CB03 SE01 SE01 CB02 CB02 SE01 SE01
*
4042533049 35735 34873-1 4042100044 3000600885 35505-1 4045264217 84781 34094
CI03 S11/6S S23/6 CA01 S011 S10/3S SE01 CB01 CA01
Qty
PM000-1 M BASIC PARTS
Item Part No.Code
O-RNG 568-021-70D
HANDWHEEL SEAL HW SEAL (.671 ID)
O-RNG 568-008-70D
HANDWHEEL COVER
105 1SE09 36811
1 1
106 107
4045200817 36793
SE01 -
2 1
103 104
4045202117
SE01 -36806-1
* * * *
*
HHCS 1/4-20 X .75 SS
4
115S11/4S 4042533004
*
*
HANDWHEEL ASSY
184449-
CB05 *
M2CP ELECTRIC CVR
184350-
CB08 *
184 & 215 CLUTCH CAM
1CA01 35730
HHCS 5/16-24 x 2.00
34042505031
S13/
(184 & 215 Frame)
HHCS 3/8-16 x 2.25SS
24042533053
S11/6S
(184 & 215 Frame)
*
3) For Item Nos. shown but not listed in Basic M Parts Listing, refer to Exploded View 83920/83920-1
ERO 20367
TM
Copyright 2018, Emerson Process Management Valve Automation, Inc., All Rights Reserved.
C
REV
DESCRIPTION
NUMBERPAGE
LHE/CL 8/21/90
REVISED DATEAPRDORIG DATEDWN
4/27/2018
DRB
115V8 29 V4
39 26 81
30 17 20
22 75 20 22
M4
1599 65
M1
45367 57
40 45 50 8
18 25 24 12 11 42
Type M (Ductile) Basic
1183775-(D)
1 of 2

March 2019
Installation, Operation and Maintenance Manual
MAN-02-10-92-0705-EN Rev. 0
11
Appendix
Appendix
83775-(D)
Type M (Ductile) Basic
11
2 of 2
8/21/90
REV
DESCRIPTION
PAGE NUMBER
REVISED DATEAPRD
LHE/CL
ORIG DATEDWN
4/27/2018
DRB
Assembly
Drawing
ERO 20367
TM
Copyright 2018, Emerson Process Management Valve Automation, Inc., All Rights Reserved.
C
57
M3 M2
M4
28 V8 8
16
37 38 V4 31
41
27
99 15 58 6 3V4 45
47 51 19 23
5610
43 44
43 44
67
107
103
73
49
106
5
105
33 103 104 36
12
25 42 13
60
24 34
Part No. Part No. Part No. PM-00-24L M 48:2L GEAR ASSY PM000-1 35820-2L 35820-4R PM000-1 PM-00-12R M 48:4R GEAR ASSY PM-00-12L M 48:4L GEAR ASSY PM000-1 35820-4L M/MG 48:4L GEAR
M/MG 48:2L GEAR M/MG 48:4R GEAR
Description
M BASIC PARTS
Description
M BASIC PARTS
Description
M BASIC PARTS
Part No. Part No.
PM-00-48R M 48:1R GEAR ASSY Part No. PM000-1 35820-1R 35820-1L PM000-1 PM-00-48L M 48:1L GEAR ASSY 35820-2R PM000-1 PM-00-24R M 48:2R GEAR ASSY
M/MG 48:1R GEAR M/MG 48:1L GEAR M/MG 48:2R GEAR M BASIC PARTS
Description
M BASIC PARTS
Description Description
M BASIC PARTS

Installation, Operation and Maintenance Manual
MAN-02-10-92-0705-EN Rev. 0 March 2019
12
Appendix
Appendix
3
Motor Removal Distane
Rectractable Handle-90°
WARNING- The installation & servicing instructions are for used by qualified personnel only.
To avoid injury and electric shock, do not perform any service on EIM equipment unless qualified.
Installation shall be in accordance with current edition of National Electric Code
or applicable regional standard.
8" H/W Swing
For electrical control pilot device elements
mounted on actuator contol cover, see EIM job
specification sheet and wiring diagram furnished
for each specific job no.
0.75" NPT
(Top & Bottom)
0.75" NPT
(Top & Bottom)
1.50" NPT
(Top & Bottom)
1
HINGE
NOTES:
1.50-11.5 NPT (2 Places) is preferred wire entry. CAUTION Conduit
must enter at lowest point to prevent water from entering electrical encolsure
due to condensation. If hazardous (classified) or NEMA 6 location, connduit seals are required at electrical enclosure entrances.
Lubrication 1/2-14" NPT plugs.
8" Handwheel shown, 12" & 16" Handwheel swing optional.
Refer to EIM Job Specification sheet for actual handwheel supplied for application.
1 2 3
11.9
(303)
5.0
(126)
4.2
(108)
Ø6.7
( 170 )
Ø9.2
(234)
7.5
( 190 )
2.6
(66)
1.5
(39)
22.8
( 579 )
24.8
( 630 )
9.2
(234)
4.6
(117)
7.5
(191)
10.8
( 275 )
17.3
( 439 )
5.2
(133)
7.6
(193)
3.6
(91)
REV ECO
THIRD ANGLE PROJECTION
DRAWING NO
REV.
DRAWN BY DATE
1 of 2
SHEET
A2
SCALE
CHECKED BY
DWG. SIZE
INTERPRET DIMENSIONS AND TOLERANCE PER
ASME Y14.5
APPROVED BY
M-2001/16G
2/18/2014
A
M/MG02 1/4T 6.500"
2/18/2014
1:4
Copyright © 2014. Emerson Process Management Valve Actuation, LLC. All Rights Reserved.
08-VAED-A
TITLE
All dimensions are in inch (mm).
A
ENATERAS
GJOSHI
BNAGTILAK
.XXX ± .005" .XX ± .020" .X APPROX.
RELEASE
DATE
1
23
45
6
7
8
910
11
12
1
23
45
6
7
8
910
11
12
A
B
C
D E F
G
H
A
B
C
D
E F
G
H
This drawing, including the information it bears, is the property of Emerson Process Management Valve Actuation,
LLC. All Rights Reserved, and must be held in strict confidence and properly safeguarded by the recipient at all times. It may not be
copied or reproduced, or provided or revealed to any other party except with the prior written authorization of Emerson Process
Management Valve Actuation, LLC. All Rights Reserved and any authorized copy or reproduction must include this legend. The
recipient may use the same only for the purpose for which Emerson Process Management Valve Actuation, LLC. All Rights
Reserved has provided it to recipient, and it must be returned to Emerson Process Management Valve Actuation, LLC. All Rights
Reserved, along with all copies and reproductions, upon request. By accepting this drawing, the recipient agrees to the foregoing.
CONFIDENTIAL:
Process Management
TM

March 2019
Installation, Operation and Maintenance Manual
MAN-02-10-92-0705-EN Rev. 0
13
Appendix
Appendix
Max Stem Engagement
22
Mounting Details: MSS Flange FA16
(4 Places)
3/4-10 UNC-2B Ta pped 1.000 (25.4) Deep,
on ø 6.500 (165) Bolt Circle
Straddle Centerline
Drive Bushing Layout
(Ref. Dwg 90806 for details)
1:3
3/8-16
Set Screw
Max Stem Acceptance
2.7
(68)
3.6
(92)
5.6
(142)
5.7
(144) 4.8
(122)
12.5
(317)
3.5
(90)
3.25
(83)
5.4
(137)
Ø9.9
(252)
W
øD
H
6.5
( 165 )
Ø6.500
(165)
11.2
(284)
5.3
(134)
7.3
(185)
DRAWING NO. REV.
2 of 2
SHEET
A2
SCALE:
SIZE
08-VAED-A
M-2001/16G A
1:4
Copyright © 2014. Emerson Process Management Valve Actuation, LLC. All Rights Reserved.
1
23
45
6
7
8
910
11
12
1
23
45
6
7
8
910
11
12
A
B
C
D E F
G
H
A
B
C
D
E F
G
H
This drawing, including the information it bears, is the property of Emerson Process Management Valve Actuation,LLC. All Rights Reserved, and must be held in strict
confidence and properly safeguarded by the recipient at all times. It may not be copied or reproduced, or provided or revealed to any other party except with the prior written authorization
of Emerson Process Management Valve Actuation, LLC. All Rights Reserved and any authorized copy or reproduction must include this legend. The recipient may use the same only for the
purpose for which Emerson Process Management Valve Actuation, LLC. All Rights Reserved has provided it to recipient, and it must be returned to Emerson Process Management Valve
Actuation, LLC. All Rights Reserved, along with all copies and reproductions, upon request. By accepting this drawing, the recipient agrees to the foregoing.
CONFIDENTIAL:

For complete list of sales and manufacturing sites, please visit
www.emerson.com/actuationtechnologieslocations or contact us at
info.actuationtec[email protected]om
World Area Conguration Centers (WACC) offer sales support, service,
inventory and commissioning to our global customers.
Choose the WACC or sales ofce nearest you:
NORTH & SOUTH AMERICA
19200 Northwest Freeway
Houston TX 77065
USA
T [phone]
Av. Hollingsworth
325 Iporanga Sorocaba
SP 18087-105
Brazil
T [phone]
ASIA PACIFIC
No. 9 Gul Road
#01-02 Singapore 629361
T [phone]
No. 1 Lai Yuan Road
Wuqing Development Area
Tianjin 301700
P. R. China
T [phone]
MIDDLE EAST & AFRICA
P. O. Box 17033
Jebel Ali Free Zone
Dubai
T [phone]
P. O. Box 10305
Jubail 31961
Saudi Arabia
T [phone]
24 Angus Crescent
Longmeadow Business Estate East
P.O. Box 6908 Greenstone
1616 Modderfontein Extension 5
South Africa
T [phone]
EUROPE
Holland Fasor 6
Székesfehérvár 8000
Hungary
T [phone]
Strada Biffi 165
29017 Fiorenzuola d’Arda (PC)
Italy
T [phone]
www.emerson.com/bettis
©2019 Emerson. All rights reserved.
The Emerson logo is a trademark and service mark of Emerson Electric Co.
BettisTM is a mark of one of the Emerson family of companies.
All other marks are property of their respective owners.
The contents of this publication are presented for information purposes
only, and while every effort has been made to ensure their accuracy, they
are not to be construed as warranties or guarantees, express or implied,
regarding the products or services described herein or their use or
applicability. All sales are governed by our terms and conditions, which are
available on request. We reserve the right to modify or improve the designs
or specifications of our products at any time without notice.