EMP OP80 User manual

Rev
Rev By
Date
Description of Change
Approved By
A
ME
8/11/20
New Release
ECN6021
B
ME
6/23/21
Revisions
ECN7292
9970039171 Rev B, 06/23/2021 © 2020, EMP Inc. 1
Quick Start Guide
OP80, OP40, and OP3530
Electric Oil Pumps
This manual is effective for consumer installations of EMP OP80, OP40 and OP3530 oil pumps.
OEM installers must contact EMP for production requirements.

Product Overview
The information contained in this manual is updated periodically. While great care is taken in compiling the information contained in this manual, Engineered
Machined Products, Inc. cannot assume liability for losses of any nature arising from any errors and/or omissions.
The information and specifications contained throughout this manual are up to date at the time of publication. Engineered Machined Products, Inc. reserves
the right to change the content of this manual at any time without notice.
© 2020, EMP Inc. 2
Engineered Machined Products, Inc.
2701 North 30th Street
Escanaba, MI, USA 49829
Phone: [phone]
www.emp-corp.com
[e-mail]
Product Overview
The EMP OP product line are electrically powered fluid pumps available in 12V DC and 24V DC configurations.
Proper installation of the pump will help ensure the performance and reliability of the electric pump while reducing
the risk of damage to other components in the system.
CAUTION:Do not use these pumps for transferring any fluids other than those for which they were
designed; to do so may damage the pump and will void the warranty.
!

Table of Contents
© 2020, EMP Inc. 3
Table of Contents
Product Overview ..............................................................................................................................................2
Introduction........................................................................................................................................................4
Purpose .........................................................................................................................................................4
Service Technician Responsibilities ...............................................................................................................4
Liability Disclaimer .........................................................................................................................................4
Additional Information ....................................................................................................................................4
Technical Help ...............................................................................................................................................4
About This Document ........................................................................................................................................5
Warnings, Cautions and Notes.......................................................................................................................5
Definition of Terms.........................................................................................................................................5
Product Safety Warnings ...................................................................................................................................6
Specifications ....................................................................................................................................................7
OP80..............................................................................................................................................................7
OP40..............................................................................................................................................................8
OP3530..........................................................................................................................................................9
Dimensions and Mounting ...............................................................................................................................10
OP80............................................................................................................................................................10
OP40............................................................................................................................................................11
OP3530........................................................................................................................................................11
Identification ....................................................................................................................................................12
EMP Oil Pump Model Codes........................................................................................................................13
Installation .......................................................................................................................................................14
Location/Orientation .....................................................................................................................................14
Plumbing......................................................................................................................................................14
Wiring Practices ...........................................................................................................................................15
Connector Information..................................................................................................................................15
R20L Component Connector Information ................................................................................................. 15
R20L Mating Connector Information ......................................................................................................... 16
R20C Component Connector Information................................................................................................. 17
R20C Mating Connector Information ........................................................................................................17
Electrical Connections..................................................................................................................................18
On/Off – Single Speed Control..................................................................................................................... 18
Example On/Off Application Schematic (7-way connector)....................................................................... 18
Operation .................................................................................................................................................18
System Fill Procedure .....................................................................................................................................19
Fluids Fill......................................................................................................................................................19
Final Item Check List....................................................................................................................................19
EMPower Connect™ Service Tool .................................................................................................................. 20
Routine Maintenance.......................................................................................................................................21
Troubleshooting...............................................................................................................................................21

Introduction
© 2020, EMP Inc. 4
Introduction
Purpose
The purpose of this quick start guide is to present information related to the pump dimensions, electrical
specifications, fluid guidelines, recommended plumbing, mounting orientation, and routine maintenance.
For production applications, the full installation specifications must be met. Contact EMP to request
documentation.
9970115018 Installation and Operation Manual OP80 Electric Oil Pump
9970094015 Installation and Operation Manual OP40 Electric Oil Pump
9970105025 Installation and Operation Manual OP3530 Electric Oil Pump
To determine if the oil pump was successfully installed, reference the Installation Review Checklist for EMP Oil
Pumps, EMP document 9890094024.
Service Technician Responsibilities
Ensure that all safety messages and information messages are read and understood before installation,
maintenance, or repairs are performed. It is important to use caution when service work is performed. Knowledge
of impacted systems and their operation are important before the removal or disassembly of any component.
Liability Disclaimer
EMP cannot anticipate every possible circumstance that might involve a potential hazard. The safety messages
in this document, in related manuals, and on the product are therefore not all inclusive. If a tool, procedure, work
method, or operating technique that is not specifically recommended by EMP is used, you must satisfy yourself
that it is safe for you and for others. You should ensure that the product will not be damaged or be made unsafe
by the operation, maintenance, or repair procedures that you choose.
Additional Information
Access https://www.emp-corp.com/support/ for service software, service bulletins, service manuals, service
drawings, and other documents related to your installed EMP systems and components. First time users may
create a free customer login at http://www.emp-corp.com/account/register/.
Technical Help
Contact EMP Customer Service for technical help at [phone] or [e-mail].

About This Document
© 2020, EMP Inc. 5
About This Document
Warnings, Cautions and Notes
Two headings are used in this document to stress your safety and safe operation of the system. They are styled
with a graphic bullet and bold, uppercase text: WARNING and CAUTION. Warnings highlight risks to
personnel — hazards, unsafe conditions and practices that can result in personal injury or death. Cautions
indicate conditions or practices that can cause damage to components, systems, or other equipment.
A third heading, styled as NOTE, calls attention to additional information about components and procedures
discussed in the document.
Definition of Terms
EMP-Link...... EMP LIN based proprietary serial data bus.
R20C ............. EMP components with CAN, temperature input and on/off control.
R20L ............. EMP components with PWM, on/off and EMP-Link control.
!
!

Product Safety Warnings
© 2020, EMP Inc. 6
Product Safety Warnings
WARNING: EMP cannot anticipate every possible circumstance that might involve a potential hazard.
The safety messages in this document, in related manuals, and on the product are therefore not all inclusive.
If a tool, procedure, work method, or operating technique that is not specifically recommended by EMP is
used, you must satisfy yourself that it is safe for you and for others. You should ensure that the product will
not be damaged or be made unsafe by the operation, maintenance, or repair procedures that you choose.
WARNING: Ensure that all safety messages and information messages are read and understood before
installation, maintenance, or repairs are performed. It is important to use caution when service work is
performed. Knowledge of impacted systems and their operation are important before the removal or
disassembly of any component.
WARNING: Make sure the equipment cannot move before doing any work or diagnostic procedures on
the EMP component, system, or vehicle.
WARNING: When working near electric components, ensure they cannot activate unexpectedly.
Remove power or utilize lock out switches.
WARNING: Use extreme caution when working on systems under pressure (i.e. coolant, hydraulic
fluids, air, fire suppression, etc.).
WARNING: Make sure the work area is ventilated and well lit.
WARNING: Make sure charged fire extinguishers are in the work area.
WARNING: Reinstall all safety guards, shields and covers.
WARNING: Make sure all tools, parts and service equipment are removed from the work area.
WARNING: Ensure that all system power and ground connection points are torqued to EMP and/or
OEM specifications to prevent system damage. Failure to follow specified torque requirements can result in
loose connections which can damage electronic components and will void EMP warranty.
!
!
!
!
!
!
!
!
!
!

Specifications
© 2020, EMP Inc. 7
Specifications
NOTE: Reference the pump performance charts for the typical performance capability of the oil pump using
a light weight oil.
NOTE: Performance will be reduced at lower operating temperatures when using lower voltage power
supplies and when using heavier weight oils.
OP80
Component Construction Cast Aluminum
Performance Model: 12V and 24V
Theoretical Displacement 0.468 in3/rev (7.67 cm3/rev)
Flow Capacity Maximum* 8.0 gal/min (30 L/min)
Operating Pressure Maximum* 80 psi (5.5 Bar)
Operating Temperature Maximum (Air) 203 °F (95 °C)
Operating Temperature Maximum (Oil) 212 °F (100 °C)
Operating Temperature Minimum 32 °F (0 °C)*
(*Sub-zero operation is application dependent)
Oil Viscosity Maximum ~5000 cSt
(Current models optimized for lighter weight oils like ATF)
Motor Speed Maximum 5000 rpm
Motor Speed Minimum 500 rpm
Motor Speed Default 4000 rpm (configurable)
Mechanical Connections Model: 12V and 24V
Suction SAE STOR -10 (7/8-14 UNF-2B)
Discharge SAE STOR -8 (3/4-16 UNF-2B)
Weight Model: 12V and 24V
Component Weight 9.5 lbs (4.3 kg)
Electrical Model: 12V Model: 24V
Input Voltage 9–16 V DC (14 V nominal) 18–32 V DC (28 V nominal)
Operating Current Draw Maximum 25 A 25 A
Thermal Protection Auto self-protect shutdown Auto self-protect shutdown

Specifications
© 2020, EMP Inc. 8
OP40
Component Construction Cast Aluminum
Performance Model: 12V and 24V
Theoretical Displacement 0.192 in3/rev (3.14 cm3/rev)
Flow Capacity Maximum* 4.0 gal/min (15 L/min)
Operating Pressure Maximum* 100 psi (6.9 Bar)
Operating Temperature Maximum (Air) 203 °F (95 °C)
Operating Temperature Maximum (Oil) 212 °F (100 °C)
Operating Temperature Minimum -40 °F (-40 °C)
(Sub-zero operation is application dependent)
Oil Viscosity Maximum ~5000 cSt
(Current models optimized for lighter weight oils like ATF)
Motor Speed Maximum 5000 rpm
Motor Speed Minimum 500 rpm
Motor Speed Default 4000 rpm (configurable)
Mechanical Connections Model: 12V and 24V
Suction SAE STOR -8 (3/4-16 UNF-2B)
Discharge SAE STOR -8 (3/4-16 UNF-2B)
Weight Model: 12V and 24V
Component Weight 9.5 lbs (4.3 kg)
Electrical Model: 12V Model: 24V
Input Voltage 9–16 V DC (14 V nominal) 18–32 V DC (28 V nominal)
Operating Current Draw Maximum 25 A 25 A
Thermal Protection Auto self-protect shutdown Auto self-protect shutdown

Specifications
© 2020, EMP Inc. 9
OP3530
Component Construction Cast Aluminum
Performance Model: 12V and 24V
Theoretical Displacement Scavenge Stage – 0.237 in3/rev (3.88 cm3/rev)
Feeder Stage – 0.204 in3/rev (3.34 cm3/rev)
Flow Capacity Maximum* Scavenge Stage – 3.9 gal/min (14.8 L/min)
Feeder Stage – 3.3 gal/min (12.5 L/min)
Operating Pressure Maximum*
60 psi (4.1 Bar) – (Feeder Stage Only)
25 psi (1.7 Bar) Relief Valve Standard
(other relief pressures available)
Operating Temperature Maximum (Air) 203 °F (95 °C)
Operating Temperature Maximum (Oil) 212 °F (100 °C)
Operating Temperature Minimum -4 °F (-20 °C)
(Sub-zero startability and operation is application dependent)
Oil Viscosity Maximum ~2000 cSt
(Current models optimized for lighter weight oils like ATF)
Motor Speed Maximum 4000 rpm
Motor Speed Minimum 500 rpm
Motor Speed Default 4000 rpm (configurable)
Mechanical Connections Model: 12V and 24V
Fluid Ports SAE STOR -8 (3/4-16 UNF-2B)
Weight Model: 12V and 24V
Component Weight 11.5 lbs (5.2 kg)
Electrical Model: 12V Model: 24V
Input Voltage 9–16 V DC (14 V nominal) 18–32 V DC (28 V nominal)
Operating Current Draw Maximum 25 A 25 A
Thermal Protection Auto self-protect shutdown Auto self-protect shutdown

Dimensions and Mounting
© 2020, EMP Inc. 10
Dimensions and Mounting
NOTE: Dimensions are given in millimeters (mm).
OP80

Dimensions and Mounting
© 2020, EMP Inc. 11
OP40
OP3530

Identification
© 2020, EMP Inc. 12
Identification
The product identification label is attached to the controller housing next to the electrical interface of the pump.
The product label contains model information and serial number. The serial number can be used to trace the
component hardware configuration, software calibration, the date of manufacture, and manufacturing data.

Identification
© 2020, EMP Inc. 13
EMP Oil Pump Model Codes
Example: OP3530-24V-EA-M
OP
35
30
-
24V
-
E
A
-
M
[OEM]
[Cert]
[Suffix]
1
2
3
4
5
6
7
8
9
10
11
12
1
Component
OP = Oil Pump
5
Voltage
9
I/O
Omit if n/a
A = Address Input
C = Temperature Input
B = Address or Temp Input
(Specified in Calibration)
P = Pressure
M = PWM High (modulated)
L = PWM Low (modulated)
–––––––––––––––––––––––
–––––––––––––––––––––––
–––––––––––––––––––––––
2
Scavenge Flow Rate
In 0.1 gallons per minute
35 = 3.5 gpm (13.2 lpm)
Omit for single stage pumps
6
Mounting
E = External Mount
C = Cartridge Mount 10
OEM
Omit if n/a
–––––––––––––––––––––––
–––––––––––––––––––––––
–––––––––––––––––––––––
3
Pressure Flow Rate
In 0.1 gallons per minute
30 = 3.0 gpm (11.4 lpm)
40 = 4.0 gpm (15.1 lpm)
80 = 8.0 gpm (30.3 lpm)
7
Orientation (degrees)
A = 0
B = 90
C = 180
D = 270
See manual for definition
11
Certification
Omit if n/a
E = E-Mark
C = CSA
U = UL
–––––––––––––––––––––––
–––––––––––––––––––––––
–––––––––––––––––––––––
4
Communication
C = CAN
Omit for on/off or PWM
8
Relief Valve Cracking
Pressure
Omit if n/a
05 = 5 psi
15 = 15 psi
25 = 25 psi
30 = 30 psi
70 = 70 psi
12
Suffix
Omit if n/a
Denotes model variation
–––––––––––––––––––––––
–––––––––––––––––––––––
–––––––––––––––––––––––
OP3530-24V-EA-M = Oil Pump. 3.5 gpm scavenge/3.0 gpm pressure, on/off/PWM communication, 24 Volt
External Mount at 0 degrees, no relief valve, uses PWM High input for commands.
NOTE: Not every option combination is available.
NOTE: All current pump models are optimized for use with lighter weight oils like ATF. Performance will be
reduced for heavier weight oils.

Installation
© 2020, EMP Inc. 14
Installation
WARNING: To avoid serious personal injury, possible death, or damage to the vehicle, disconnect the
power supply, main negative battery cable, and/or switch off the battery disconnect switch before
installation or servicing. When working on or near the electric components, ensure battery power is off or
lock out vehicle ignition, so the system cannot activate unexpectedly.
WARNING: To avoid burn injuries, allow time for the engine to cool to a safe working temperature
before removing or installing any components.
CAUTION: To avoid potential damage to the wiring and/or hoses, route all wires and hoses away from
any sharp edges, moving objects, and heat sources.
CAUTION: All wires should be secured every 12–18 inches and anywhere motion could result in wires
rubbing against any other surface. All zip ties must be placed over wire loom/convoluted tubing and not
over bare wires.
Location/Orientation
•Operating temperature limits must be considered during installation.
•Whenever possible, the pump should be mounted with the wires facing down. Although the pump will run in
any orientation, it is preferred that the pump be mounted in the horizontal orientation. If the pump must be
mounted in a vertical orientation, the wire routing will need to be adjusted. Reference the wiring section.
•Select a mounting location as close as possible to the oil supply.
•Ensure there is a minimum of 13mm (1/2”) of clearance to ensure there is no rubbing or interference during
operation.
•Securely attach pump to frame or mounting bracket by using (4) M8 x 1.25 fasteners. The mounting holes
are tapped to a depth of 16mm. Be aware of the bracket thickness when selecting the fastener length to
ensure a minimum thread engagement of 12mm while not bottoming out in the pump housing. Tighten
fasteners to a torque of 20 N-m.
Plumbing
NOTE: Inlet and Outlet ports are identified under the Dimensions and Mounting section.
NOTE: All pump connections rely on an O-ring sealing method, do not use thread sealant or tape.
•For optimal performance, it is recommended that hose or lines be no smaller than minimum recommended
diameter. The supply hose (suction) should be kept as short as possible.
•Minimum recommended diameters:
OP80 ¾” ID
OP40 ⅝” ID
OP3530 ⅝” ID
•Avoid restrictions such as sharp bends and undersized fittings in lines.
•Avoid routing hoses/lines in areas that would cause chafing. All hoses should be secured to prevent rubbing
against any surfaces.
•Ensure all fittings, lines, and hoses are selected based on appropriate ratings for the application
(temperature, pressure, fluid type, etc.).
•It is recommended that the fluid quality meets ISO cleanliness code 20/18/15. This is representative of the
nominal filtration of 20 microns or better.
•It is recommended that a strainer on the suction side of the pump be used. The strainer will keep foreign
matter from entering the pump and reduce the risk of the pumping element seizing up. The strainer mesh
size should be large enough so that it does not cause excessive pressure drop, but fine enough to protect
the pump.
!
!
!
!

Installation
© 2020, EMP Inc. 15
Wiring Practices
•For proper controller operation, the ignition enable line must not be tied to power. It must be supplied from a
separate DC switched source which allows the pump to be turned off before power is removed. Failure to do
so prevents the controller from going through its normal shutdown routine.
•The maximum current draw for EMP OP oil pumps is 25 amps. The actual pump current draw varies with oil
viscosity and the pressure required to pump the oil through the system. It is recommended to install a properly
sized fuse, not less than 30A on the power supply line to protect installed wiring.
•Although the pump connector and mating connector are environmentally sealed, care must still be taken to
prevent water from pooling up on the pump connector or the sealing grommet on the pump motor housing.
This can be achieved through proper wire harness routing.
•Route motor lead harness down and away from the pump sealing grommet. Ensure that there is a minimum
of approximately 1.5 inches (38 mm) of straight wire length exiting the sealing grommet prior to changing
wire routing directions.
•Care should be taken to ensure no stress or strain is placed on the interface between the wires and the
connectors else the sealing mechanism could be compromised.
•It is good practice to incorporate drip loops into the wire routing design. Always ensure the connectors are
not located in the bottom of the loop as the water runs off at the lowest point in the harness.
•It is recommended that the pump connector(s) are oriented so that water flows down and past the
connectors.. This will prevent water from pooling on the seal between the mating connectors.
•The voltage drop between the battery or power supply and the pump should not exceed 5% of the rated
voltage. This should be verified at the pump’s maximum current draw once all electrical connections are
completed. Systems with excessive voltage drops will yield reduced pump performance.
Connector Information
The following notes apply to all connectors:
NOTE: All cavities in the mating connector must either be terminated or plugged to prevent moisture from
entering the component.
NOTE: Ensure wires are sized appropriately for the application. Wire gauges and circuit protection shown in
this document are suggestions.
NOTE: Do not disconnect the component while it is running; stop running the component prior to
disconnecting the connector.
R20L components use a 7-way Delphi Metripack connector. R20C components use either a single 10-way
connector or separate 2-way and 6-way connectors.
R20L Component Connector Information
Connector Greasing
NOTE: See Service Bulletin Approved Grease EMP document 9910039075, for a list of dielectric grease
products that have been approved for use in maintenance and service. The document can be obtained on
the EMP website by searching for the document number.
NOTE: Only use clean dielectric grease.
1. Apply dielectric grease to each harness side electrical connector. See the table below for specified grease
amounts.
Dielectric Grease Reference Quantities
Grease
Description
1.25 g
Delphi 7-way mating connector

Installation
© 2020, EMP Inc. 16
7-Way Male Delphi Metripack 150/480 Sealed
Pin
Purpose
Wire Size and Color
A
Unused
16 AWG Black/Tan
B
Optional (Ground for TACH_OUT)
16 AWG Black/Yellow
C
Ignition enable
16 AWG Black/Purple
D
Optional (TACH_OUT)
16 AWG Black/Green
E
Battery power
10 AWG Black/Red
F
Unused
16 AWG Black/White
G
Ground
10 AWG Black
R20L Mating Connector Information
NOTE: All cavities in the mating connector must either be terminated or plugged to prevent moisture from
entering the component.
7-Way Female Delphi Metripack 150/480 Sealed
The connector on the component is a sealed Delphi 480/150 Metripack mixed connector with male terminals.
NOTE: A service kit containing all parts needed for one mating connector is available from EMP. The service
kit part number is 1370036093, and the service kit drawing is available on the EMP website and can be
obtained at www.emp-corp.com/support/documents by searching for the service kit part number.
Item
Delphi Part Number
Connector
12059472
TPA
12052486
480 Terminal
12052139
150 Terminal
12048074
480 Seal
15324990
150 Seal
15324973
150 Plug
12059168

Installation
© 2020, EMP Inc. 17
R20C Component Connector Information
10-Way Male Apex 2.8mm Sealed
Pin
Purpose
Wire Size and Color
1
Battery power
10 AWG Black/Red
2
Plugged
Plugged
3
Unused
16 AWG Black/White
4
Unused
16 AWG Black/Tan
5
Unused
16 AWG Black/Yellow
6
Ignition enable
16 AWG Black/Purple
7
Plugged
Plugged
8
Ground
10 AWG Black
9
Plugged
Plugged
10
Unused
16 AWG Black/Green
R20C Mating Connector Information
Power/Ground/Communication Connector: 10-Way Female Apex 2.8mm
Detail
Apex Part Number
Alternative Part Number
Connector
54201009
15316895
Terminal, Apex 2.8mm, Socket, 10 – 12 AWG 54001000 10762802
Terminal, Apex 2.8mm, Socket, 14 – 16 AWG 54001400 10762803
Terminal, Apex 2.8mm, Socket, 18 – 20 AWG 54001800 10757690
Apex 2.8mm Grey Plug 54200005 N/A
NOTE: A service kit containing all parts needed for one mating connector is available from EMP. The service
kit part number is 1370106076.

Installation
© 2020, EMP Inc. 18
Electrical Connections
Power is supplied from a 12V or 24V DC (nominal) source depending on model type. The component receives
power through the battery power pin of the connector (Reference the appropriate section of Connector
Information for component pin descriptions). The ignition enable is a switched power source which is sent from
your system to initiate operation of the component. This can be wired directly to a vehicle ignition, to a PLC
output, through a manual switch or through a thermal switch. This line will draw less than 10 mA of current. All
switches on this line can be sized based on this amperage requirement. This input should be fused close to the
source to protect the vehicle or system wiring.
On/Off – Single Speed Control
NOTE: All cavities in the mating connector(s) must either be terminated or plugged to prevent moisture
from entering the component.
NOTE: EMP parts kit 1370056018 includes a mini-fuse holder, cover, fuses, and the wiring parts required
for installation of the holder.
NOTE: 10 AWG wire can be used for power and ground. Use Delphi 480 cable seal #15324990.
Example On/Off Application Schematic (7-way connector)
Operation
When power is on and ignition enable is on, the component will run in an on/off, single speed manner. The speed
at which the component will run will be the pre-configured default speed.
EMP OP pumps are also available with CAN, PWM, temperature input and EMP-Link control. Contact EMP for
more information.
NOTE: For assistance with component calibrations and settings, please contact EMP Technical Service at
[e-mail] and provide a serial number for the part in question.

System Fill Procedure
© 2020, EMP Inc. 19
System Fill Procedure
Fluids Fill
CAUTION:Do not use these pumps for transferring any fluids other than those for which they were
designed; to do so may damage the pump and will void the warranty.
Follow these instructions each time the system is drained:
1. System fill instructions must be developed, documented, and verified by the system integrator. OEM
integrators must communicate these procedures to the end customer in their maintenance documentation.
2. Caution must be taken to ensure the system is refilled properly to ensure effective priming of the pump. (For
new pumps, pour oil into the pump discharge port to wet the pumping element.)
3. Use care to avoid contaminating oil with debris when working on the system or pump.
Final Item Check List
•Are all hoses, fittings, and lines appropriately sized?
•Are the oil supply and delivery lines to and from the pump securely fastened?
•Is the pump supplied with the appropriate voltage?
•Is the pump securely mounted?
•Are all wires and/or hoses routed away from sharp edges, moving objects, and heat sources?
•Is the ignition enable on a switched source and not tied to power?
!

EMPower Connect Service Tool
© 2020, EMP Inc. 20
EMPower Connect™ Service Tool
EMP Service Suite is available at no cost on the EMP website. To use the EMPower Connect service tool,
download and install the Service Suite software on a Windows PC. EMPower Connect software allows the user
to monitor operation, manually control the component and collect history data from the controller.
Use breakout harness 3180036020 to interface with the 7-pin component connector and an EMP TTL/EMP-Link
data link adapter 3640036049. These are available together in diagnostic kit number 7500038004.
For CAN components use breakout harness 3170073176 to interface with the power and ground and
communication connectors and an RP1210 compatible data link adapter.
The Service Suite User Guide and Tutorial,including connection and control instructions, is embedded in the
software and available on the EMP website.
To view diagnostic code lists or troubleshooting guides when not connected to a component, select the guide
matching the control platform of the component from the Trouble Shooting menu.