Empire RH-25-5 Quick start guide

Page 1R-2065
VENTED
ROOM HEATER
MODELS
RH-25-5
RH-35-5
EFFECTIVE DATE
JUNE, 2000
INSTALLATION INSTRUCTIONS
AND
OWNER’S MANUAL
WARNING: If the information in
this manual is not followed exactly, a
fire or explosion may result causing
property damage, personal injury or
loss of life.
— Do not store or use gasoline or other
flammable vapors and liquids in the
vicinityofthisoranyotherappliance.
— WHATTODOIFYOUSMELLGAS
•Do not try to light any appliance.
•Donottouchanyelectricalswitch;
donotuseanyphoneinyourbuild-
ing.
•Immediatelycallyourgassupplier
from a neighbor’s phone. Follow
the gas supplier’s instructions.
•If you cannot reach your gas sup-
plier, call the fire department.
— Installation and service must be per-
formedbyaqualifiedinstaller,service
agency or the gas supplier.
WARNING: If not installed, operated
and maintained in accordance with the
manufacturer’sinstructions, this prod-
uct could expose you to substances in
fuel orfrom fuel combustion which can
cause death or serious illness.

Page 2 R-2065
Notice: Duringinitialfiring of thisunit,itspaint will bakeout
and smoke will occur. To prevent triggering of smoke alarms,
ventilate the room in which the unit is installed.
Installation on Rugs and Tile
If this appliance is to be installed directly on carpeting, tile, or
other combustible material, other than wood flooring, the
appliance shall be installed on a metal or wood panel extend-
ing the full width and depth of the appliance.
The base referred to above does not mean the fire-proof base
as used on wood stoves. The protection is primarily for rugs
that may be extremely thick and light-color tile that can
discolor.
Heater pad is available from Empire Comfort Systems, Inc.,
Part No. RH-425.
Specifications
Model RH-25-5 RH-35-5
Input BTU/HR (KW/H) 25,000 (7.3) 35,000 (10.3)
Height 26" (660mm) 26" (660mm)
Width 37" (940mm) 37" (940mm)
Depth including diverter 18 3/8" (467mm) 18 3/8" (467mm)
Gas Inlet Pipe 1/2" (13mm) 1/2" (13mm)
Size of flue collar 4 “ (102mm) 4” (102mm)
Floor to top of collar on verti-
cal position of Draft Diverter 2215/16"(583mm) 2215/16"(583mm)
Floortocenterofcollaronhori-
zontalpositionofDraftDiverter 18 3/16" (462mm) 18 3/16" (462mm)
Accessories
Blower Package DRB-1 DRB-1
Heater Pad RH-425 RH-425
Introduction
Always consult your local Building Department regarding
regulations, codes or ordinances which apply to the installa-
tion of a vented room heater.
Instructions to Installer
1. Installer must leave instruction manual with owner after
installation.
2. Installer must have owner fill out and mail warranty card
supplied with vented room heater.
3. Installer should show owner how to start and operate
vented room heater and thermostat.
Warning:
Any change to this vented room heater or its controls
can be dangerous. Any safety screen or guard re-
moved for servicing a vented room heater must be
replaced prior to operating the vented room heater.
General Information
This series is design certified in accordance with American
National Standard / CSA Standard Z21.86b-1998 and CSA
2.32b-M98 by the American Gas Association and Canadian
Gas Association, as a Vented Room Heater and must be
installed according to these instructions.
Any alteration of the original design, installed other than
as shown in these instructions or use with a type of gas not
shownontherating plateistheresponsibilityoftheperson
and company making the change.
Important
All correspondence should refer to complete Model No.,
Serial No. and type of gas.
• Due to high temperatures, the room heater should be
located out of traffic and away from furniture and drap-
eries.
• Children and adults should be alerted to the hazards of
high surface temperature and should stay away to avoid
burns or clothing ignition.
• Youngchildrenshouldbecarefullysupervised whenthey
are in the same room as the room heater.
• Clothingorotherflammablematerialshouldnotbeplaced
on or near the room heater.
• Duetohighsurfacetemperatures,keepchildren,clothing
and furniture away.
• Keep burner and control compartment clean.
• Installation and repair should be done by a QUALIFIED
SERVICE PERSON. The room heater should be in-
spected before use and at least annually by a qualified
service person. More frequent cleaning may be required
due to excessive lint from carpeting, bedding material,
etc. It is imperative that control compartments, burners
and circulating air passageways of the room heater be
kept clean.
• DO NOT put anything around the heater that will ob-
struct the flow of combustion and ventilation air. See
clearances.
• DO keep the appliance area clear and free from combus-
tible material, gasoline and other flammable vapors and
liquids.
• DO examine venting system periodically. Clean and
replacedamaged parts. Examinationsshould bemadeat
the start of the heating season and also in mid heating
season under average conditions.
• DO examine burners periodically. Clean and replace
damaged parts.
• DONOTusethisheaterifanyparthasbeenunderwater.
Immediately call a qualified service technician to inspect
the heater and to replace any part of the control system
and any gas control which has been under water.
THIS IS A HEATING APPLIANCE
DO NOT OPERATE THIS APPLIANCE WITHOUT FRONT PANEL INSTALLED.

Page 3R-2065
Some people cannot smell well. Some people cannot smell
the odor of the chemical stench put into the gas. You must
findoutifyoucansmelltheodorantinpropane. Smokingcan
decrease your ability to smell. Being around an odor for a time
can affect your sensitivity or ability to detect that odor. Some-
times other odors in the area mask the gas odor. People may not
smell the gas odor or their minds are on something else. Think-
ing about smelling a gas odor can make it easier to smell.
The odorant in LP-gas is colorless, and it can fade under
some circumstances. For example, if there is an underground
leak,themovementofthegasthroughsoilcanfilter the odorant.
Odorants in LP-Gas also are subject to oxidation. This fading
by point with the members of your household. Someday
whentheremaynotbeaminutetolose,everyone'ssafetywill
depend on knowing exactly what to do. If, after reading the
followinginformation, youfeel youstill needmore informa-
tion, please contact your gas supplier.
Propane (LP-Gas) is a flammable gas which can cause fires
and explosions. In its natural state, propane is odorless and
colorless. Youmaynotknowallthefollowingsafetyprecau-
tions which can protect both you and your family from an
accident. Read them carefully now, then review them point
can occur if there is rust inside the storage tank or in iron gas
pipes.
The odorant in escaped gas can adsorb or absorb onto or into
walls, masonry and other materials and fabrics in a room. That
will take some of the odorant out of the gas, reducing its odor
intensity.
LP-Gasmaystratifyinaclosedarea,andtheodorintensitycould
varyat differentlevels. Since it isheavier thanair,there maybe
more odor at lower levels. Always be sensitive to the slightest
gas odor. If you detect any odor, treat it as a serious leak.
Immediately go into action as instructed earlier.
•LearntorecognizetheodorofLP-gas. YourlocalLP-Gas
Dealer can give you a "Scratch and Sniff" pamphlet. Use it
to find out what the propane odor smells like. If you suspect
thatyourLP-Gashas a weakor abnormal odor,call your LP-
Gas Dealer.
• If you are not qualified, do not light pilot lights, perform
service, or make adjustments to appliances on the LP-Gas
system. Ifyouarequalified,consciouslythinkabouttheodor
ofLP-Gas priortoand while lightingpilotlights orperform-
ing service or making adjustments.
• Sometimes a basement or a closed-up house has a musty
smell that can cover up the LP-Gas odor. Do not try to light
pilot lights, perform service, or make adjustments in an area
where the conditions are such that you may not detect the
odor if there has been a leak of LP-Gas.
• Odor fade, due to oxidation by rust or adsorption on walls of
new cylinders and tanks, is possible. Therefore, people
should be particularly alert and careful when new tanks or
cylinders are placed in service. Odor fade can occur in new
tanks, or reinstalled old tanks, if they are filled and allowed
to set too long before refilling. Cylinders and tanks which
have been out of service for a time may develop internal rust
whichwill causeodor fade. If suchconditions are suspected
to exist, a periodic sniff test of the gas is advisable. If you
have any question about the gas odor, call your LP-gas
dealer. A periodic snifftest of theLP-gas is agood safety
measure under any condition.
• If, at any time, you do not smell the LP-Gas odorant and you
think you should, assume you have a leak. Then take the
sameimmediateactionrecommendedabovefortheoccasion
when you do detect the odorized LP-Gas.
• If you experience a complete "gas out," (the container is
under no vapor pressure), turn the tank valve off immedi-
ately. Ifthecontainervalveislefton,thecontainermaydraw
in some air through openings such as pilot light orifices. If
this occurs, some new internal rusting could occur. If the
valve is left open, then treat the container as a new tank.
Always be sure your container is under vapor pressure by
turningitoffatthecontainerbeforeitgoescompletelyempty
or having it refilled before it is completely empty.
SAFETY INFORMATION FOR USERS OF LP-GAS
• Do not operate electric switches, light matches, use your
phone. Do not do anything that could ignite the gas.
• Geteveryoneoutofthebuilding,vehicle,trailer,orarea. Do
that IMMEDIATELY.
• Close all gas tank or cylinder supply valves.
• LP-Gas is heavier than air and may settle in low areas such
as basements. When you have reason to suspect a gas leak,
keep out of basements and other low areas. Stay out until
firefighters declare them to be safe.
• Useyourneighbor'sphoneandcallatrainedLP-Gasservice
person and the fire department. Even though you may not
continue to smell gas, do not turn on the gas again. Do not
re-enter the building, vehicle, trailer, or area.
•Finally, let the service man and firefighters check for
escaped gas. Have them air out the area before you return.
Properly trained LP-Gas service people should repair the
leak, then check and relight the gas appliance for you.
SOME POINTS TO REMEMBER
NO ODOR DETECTED - ODOR FADE
LP-GAS WARNING ODOR
If a gas leak happens, you should be able to smell the gas because of the odorant put in the LP-Gas.
That's your signal to go into immediate action!

Page 4 R-2065
Qualified Installing Agency
Installation and replacement of gas piping, gas utilization equipment or
accessoriesandrepairandservicingofequipmentshallbeperformedonly
byaqualifiedagency. Theterm“qualifiedagency”meansanyindividual,
firm, corporation, or company which whether in person or through a
representative is engaged in and is responsible for (a) the installation or
replacement of gas piping or (b) the connection, installation, repair or
servicing of equipment, who is experienced in such work, familiar with
allprecautionsrequired andhascompliedwithall therequirementsof the
authority having jurisdiction.
The installation must conform to local codes or, in the absence of local
codes, with the National Fuel Gas Code, ANSI Z223.1 */Canadian
Installation Code, CAN/CGA B149.
*AvailablefromtheAmericanNationalStandardsInstitute,Inc.,11West42ndSt.,
New York, NY 10036.
Locating and Venting the Room Heater
Clearances: When facing the front of the room heater the minimum
clearances to combustible construction (material) are the following:
Right side 6 inches (152mm).Left side 6 inches (152mm).
Recommend 18 inches (457mm) on left side for servicing.
Do not install in alcove or closet. No horizontal projection above heater
permitted within 48 inches (122cm).
Ceiling 48 inches (122cm). Rear of draft hood 2 inches (51mm).
Open in front to provide service, access, and clearance to combustibles.
Venting
1. Flue pipe must be as large as the flue collar on the draft diverter.
2. Maintain an upward slope of at least 1/4 inch (6mm) per foot (.3m)
of horizontal run.
3. Run flue pipe as directly as possible with a minimum of elbows.
4. Flue pipe should extend through the wall of a chimney to be flush
with inner wall.
5. Flue pipe must be adequately supported by metal strips.
6. Single wall vent pipe may be attached directly to the draft hood of
the room heater when a clearance of 2 1/2 inches (64mm) is
maintained between the single wall vent pipe and the combustible
walloftheroominwhichtheroomheaterislocated. Usedoublewall
vent pipe for clearances less than 2 1/2 inches (64mm) to combus-
tibles.
7. Forfluepiperunningthroughwallsandroof,useB-1[1inch(25mm)
clearance to combustibles) vent pipe.
8. Chimneys should extend at least 2 feet (.6m) above the roof and
above any object or nearby building within 10 feet (3m).
9. Open tees should not be used in the flue pipe.
10. Appliance must not be connected to a chimney flue that is servicing
a separate solid-fuel burning appliance.
For proper venting, do not attach a 90°elbow directly to draft diverter.
If possible, attach 2 feet (.6m) of straight vent pipe before an elbow is
used. Use 45°elbows if possible.
Uninsulatedsingle-wallmetalpipeshallnot be used outdoors in cold
climates for venting gas utilization equipment.
Ventilation and Combustion Air
Room heaters shall be installed in a location in which the facilities for
ventilation permit satisfactory combustion of gas and proper venting
under normal conditions. In buildings of conventional frame, brick or
stone construction without tight storm windows and doors, infiltration is
normally adequate to provide for combustion and draft hood dilution.
Where appliances are installed in a confined space within a building, the
building being of unusually tight construction, air for combustion and
ventilationmust beobtained directly fromoutdoors or from suchspaces
that freely communicate with the outdoors. Under these conditions, the
confined space shall be provided with two permanent openings, one near
thetopof the enclosure and one near the bottom;eachopeningshall have
a free area of not less than one square inch (6.5cm2)per 1,000 BTU’s
(.3KW/H)of totalinput. Thedraft hoodmustbe inthesame atmospheric
pressure zone as the combustion air inlet to the appliance.
Gas Supply
Checkalllocal codes for requirements, especially forthesize and type of
gas supply line required. On Natural gas lines less than 15' (4.6m) long,
use1/2"(13mm)pipe;onlongerruns,use3/4"(19mm)ironpipeorequal.
On LP gas lines please consult LP gas supplier.
Installing a New Main Gas Cock
Each appliance should have its own manual gas cock.
A manual main gas cock should be located in the vicinity of the unit.
Where none exists, or where its size or location is not adequate, contact
your local authorized installer for installation or relocation.
Compounds used on threaded joints of gas piping shall be resistant to the
action of liquefied petroleum gases. The gas lines must be checked for
leaksby theinstaller. Thisshould bedonewith asoap solution, watching
for bubbles on all exposed connections and, if unexposed, a pressure test
should be made.
Never Use an Exposed Flame to Check for Leaks.
Appliancemustbe disconnected from piping at inletof control valve
and pipe capped or plugged for pressure test. Never Pressure Test
With Appliance Connected; Control Valve Will Sustain Damage!
A gas valve and ground joint union should be installed in the gas line
upstream of the gas control to aid in servicing. It is required by the
NationalFuelGasCodethatadriplinebeinstallednearthegasinlet. This
should consist of a vertical length of pipe, tee connected into the gas line,
that is capped on the bottom in which condensation and foreign particles
may collect.
Method of Installing A Tee Fitting Sediment Trap
The use of the following gas connectors is recommended:
— ANS Z21.24 Appliance Connectors of Corrugated Metal Tubing
and Fittings
— ANS Z21.45 Assembled Flexible Appliance Connectors of Other
Than All-Metal Construction
The above connectors may be used if acceptable by the authority having
jurisdiction.
Pressure Testing of the Gas Supply System
1. To check the inlet pressure to the gas valve, a 1/8" (3mm) N.P.T.
plugged tapping, accessible for the test gauge connection, must be
placed immediately upstream of the gas supply connection to the
appliance.
2. Theappliance, and itsindividual shutoff valve,must be disconnected
from the gas supply piping system during any pressure testing of
that system at test pressures in excess of 1/2 psig (3.5kPa).
3. The appliance must be isolated from the gas supply piping system by
closing its individual manual shutoff valve during any pressure
testingofthegassupplypipingsystemattestpressuresequaltoorless
than 1/2 psig (3.5kPa).

Page 5R-2065
Attention! If one of the above procedures results in pressures in excess
of 1/2 psig (14" w.c.) (3.5kPa) on the appliance gas valve, it will result in
a hazardous condition.
Checking Manifold Pressure
Both Propane and Natural gas valves have a built-in pressure regulator
that has a sealed adjustment. Natural gas models will have a manifold
pressure approximately 4.0" w.c. (.996kPa) at the valve outlet with the
inletpressuretothevalvefromaminimumof5.0"w.c.(1.245kPa)forthe
purpose of input adjustment to a maximum of 10.5" w.c. (2.61kPa).
Propanegasmodelswillhaveamanifoldpressureapproximately10.0"w.c.
(2.49kPa) at the valve outlet with the inlet pressure to the valve from a
minimum of 11.0" w.c. (2.739kPa) for the purpose of input adjustment
to a maximum of 13.0" w.c. (3.237kPa)
A 1/8" (3mm) N.P.T. plugged tapping, accessible for test gauge connec-
tion is located on the outlet side of the gas control.
Liner and Insulated Liner
When you install a vented room heater into a masonry chimney you
must follow these steps.
1. The chimney must be lined and sized properly. Most masonry
chimneys are over sized and absorb too much heat to be considered
apropervent. If you haveanydoubts line the chimney withtheright
size liner. If it’s unlined you must line it.
2. Useaninsulatedlinerwhenthechimneyisontheoutside,threesides
exposedtotheweather,andthereisnoclaylinerinthechimney.The
insulation will help keep the flue gases warmer.
Insulated Vent Enclosure
Ventedroom heatersinstalled withthe ventgoingdirectlytothe outside
and above the eaves can cause poor venting. The cold pipe will have a
delay in proper venting and cause the room heater to shut “off” by the
vent safety switch. To prevent delayed venting as well as condensation
of flue products an insulated enclosure is recommended.
Use type B 4" (102mm) diameter vent pipe and maintain at least a one
inch (25mm) clearance to combustibles.
Usemetalthimbletoprotectventpipeasitpassesthroughcombustibles.
High Altitudes
For altitudes/elevations above 2,000 feet (610m), input ratings should
be reduced at the rate of 4 percent for each 1,000 feet (305m) above sea
level. Canadian High Altitudes for locations having an elevation
abovemeansealevelbetween2,000feet(610m)and4,500feet(1370m),
themanifoldpressureistobedecreasedfrom4.0"w.c.(.996kPa) to3.2"
w.c. (.797kPa) for Natural Gas and from 10.0" w.c. (2.49kPa) to 8.0"
w.c. (1.99kPa) for Propane Gas.
Piezo Pilot Ignitor Instructions
Depressingtheredbuttoncompletelycausesasparktooccuratthepilot.
To light the pilot, it is important that the electrode be 1/8" (3mm) from
the thermocouple. The spark must occur at the point the burner flame
hits the thermocouple. The end of the electrode will be red hot with the
pilot “On”.
On a new installation with air in the gas line, it is suggested that a match
be used. The match will light the pilot faster than the piezo under this
condition.
Vent Safety Shutoff System
This heater must be properly connected to a venting system. This heater
is equipped with a vent safety shutoff system.
Warning:
Operation of this heater, when not connected to a properly
installed and maintained venting system or tampering with the
vent safety shutoff system, can result in carbon monoxide (CO)
poisoning and possible death.
This appliance needs fresh air for safe operation and must be installed so
there are provisions for adequate combustion and ventilation air.
This room heater is equipped with a vent safety switch. The vent
safety switch will cause gas flow to the pilot to “shut off” due to
improper venting or a blocked flue.
If the vent safety switch continues to “shut off” the gas flow to the
pilot a qualified service person must be contacted to inspect for
improper venting, blockage in the vent pipe or the vent safety switch
for being defective.
DRAFT DIVERTER CAN BE EITHER A VERTICAL VENT OR HORIZONTAL VENT
Reversible Vertical or Horizontal Draft Diverter
This room heater has a reversible draft diverter. The draft diverter is
installed in the vertical position at the factory. Please use the following
steps to change the draft diverter from the vertical position to the
horizontal position.
1. Remove L280 vent safety switch from the draft diverter.
2. Inside your yellow instruction envelope will be a 1 1/2" x 2 1/4"
(38mm x 51mm) vent safety switch hole cover plate and two (2)
1/2" screwsfor attachment of vent safety switch hole cover plate to
the draft diverter. Attach vent safety switch hole cover plate over
holeonthedraftdiverterfromwhichtheL280ventsafetyswitchwas
removed.
3. Removetwo (2)screwsat bottomofdraft diverterandlift upwardto
remove draft diverter from the draft diverter plate. Rotate draft
diverter into the horizontal position and slide back into the draft
diverter plate. Attach two (2) screws into bottom of the draft
diverter.
4. Removevent safetyswitch holeknockout andtwo (2)knockoutsfor
screws on opposite side of draft diverter.
5. Attach L280 vent safety switch to the draft diverter.
6. Repositioning of the draft diverter is completed.
MORE THAN 10'
(3m)
10' (3m)
2' (.6m)
HEIGHT ABOVE ANY ROOF SURFACE
WITHIN 10' (3m) HORIZONTALLY
3' (.9m)

Page 6 R-2065
Figure 2
To Remove Main Burner
1. Disconnect the thermocouple and pilot supply line at the pilot
burner.
2. Unscrew the nut on the orifice fitting union. Orifice fitting is
threaded into the main burner.
3. Remove screw on each side of the main burner and lift out.
To Remove Main Burner Orifice
1. Unscrew the nut on the orifice fitting union. Orifice fitting is
threaded into the main burner.
2. Unthread the orifice fitting from the main burner.
3. Main burner orifice is located at the end of the orifice fitting.
4. Removemainburnerorificefrom orifice fitting with a 1/2" (13mm)
wrench.
Cleaning Combustion Chamber
Aqualifiedservicemanshouldremovethechamberandapplyairpressure
to the inside in order to clear all passageways.
Thermostat Operation
Toturnonburner,rotatedialknobtowardsettingnumber9. Toshutdown
burner, rotate dial knob toward number 1.
The dial numbers 1 through 9 correspond to 58°(14°C) through 90°F
(32°C). This is the temperature at the bulb thermostat not the room
temperature. Theownerisadvisedtodeterminetheparticularheatsetting
thatisdesiredforcomfort,asheating requirementsare differentfor every
owner.
Attention: When the dial knob is turned below number 1, to the white
indicator mark and the bulb temperature drops to 55°F (13°C), the
thermostat will call for heat and the main burner will ignite.
If no heat is desired, turn the gas control knob to the PILOT position.
Optional Blower Warning:
Unplugging of blower accessory will not stop the heater from
cycling. To shut heater off:
1. Turn temperature dial or thermostat to lowest setting.
2. Turn knob on gas control to “OFF”, depressing slightly. Do
not force.
Proper Pilot Flame (Figure 1)
Thecorrectflamewillbealmosthorizontal,blueandwillextendpastthe
thermocouple 1/4" (6mm). The flame will surround the thermocouple
just below the tip.
On Propane(LP-gas)slightyellowmightoccurwherethepilotflameand
the burner flame meet.
Natural gas pilots require adjusting when the inlet pressure is above 5"
w.c. (1.25kPa) Remove pilot adjustment cover. Turn adjustment screw
clockwise to reduce flame.
Propane (LP-gas) will not require adjusting.
After use, cleaning of the pilot burner may be required for the proper
flame. Thepilotorificecanbecleanedwithhighpressureairorbyplacing
under running water. Pilot orifice must be dry before replacement. Use
a pipe cleaner to clean inside the pilot after the pilot orifice has been
removed.
To Remove Pilot Orifice
1. Disconnect the pilot supply line at the pilot burner.
2. Removepilot orifice frompilotburner.It may benecessaryto tap on
pilot burner in order to remove the pilot orifice.
Figure 1
Proper Main Burner Flame (Figure 2)
Therewillbeashortblueinnerflamewitha larger,lighterbluesecondary
flame. The burner flame may have yellow tips when hot. Dust in the
combustion air will produce an orange or red flame. Do not mistake the
orange or red flame for an improper yellow flame.
Attention: OnPropanegas,ifawhistlingnoise(resonation)occursclose
theairshutteronthemainburnerinordertoreducetheamountofprimary
air. The reduction in primary air will soften the main burner flame and
will eliminate the whistling noise (resonation).
On Propane or Natural gas if a yellow flame occurs open the air shutter
on the main burner in order to increase the amount of primary air. The
increaseinprimaryairwillsharpenthemainburnerandwilleliminatethe
yellow flame.
After use, cleaning of the main burner may be required for the proper
flame. The main burner may be cleaned by forcing water into the ports
and the throat of the burner. The burner should be blown dry or heated to
remove all water before replacement.

Page 7R-2065
TO TURN OFF GAS TO APPLIANCE
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion may result
causing property damage, personal injury, or loss of life.
3. Push in gas control knob slightly and turn clock-
wise to “OFF”. Do not force.
A. This appliance has a pilot which must be lighted by
hand. Whenlighting thepilot,followtheseinstructions
exactly.
B. BEFORE LIGHTING smell all around the appliance
area for gas. Be sure to smell next to the floor because
some gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch;
do not use any phone in your building.
• Immediately call your gas supplier from a neigh-
bor’sphone. Followthegassupplier’sinstructions.
• Ifyoucannotreachyourgassupplier,callthefire
department.
C. Useonlyyourhandtopushinorturnthegascontrol
knob. Never use tools. If the knob will not push in
or turn by hand, don’t try to repair it; call a
qualified service technician. Force or attempted
repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under
water. Immediately call a qualified service techni-
ciantoinspecttheapplianceand toreplaceany part
of the control system and any gas control which has
been under water.
1. Set thermostat to lowest setting.
2. Turn off all electric power to appliance ( if applicable)
if service is to be performed.
LIGHTING INSTRUCTIONS
6. Remove casing front
from the heater and
observe the pilot by
lifting pilot cover.
7. Turnknobongascontrolcounterclockwise
to “PILOT.”
8. Push and hold control knob in and repeatedly push
the ignitor button until pilot is lit (or use match to
light). Continuetoholdthecontrolknobinforabout
one(1)minuteafterthepilotislit. Releaseknoband
itwillpop backup. Pilot shouldremainlit. Ifitgoes
out, repeat steps 4 through 8.
• Ifknobdoesnot popup whenreleased,stopand
immediately call your qualified service techni-
cian or gas supplier.
• If the pilot will not stay lit after several tries,
turn the gas control knob to “OFF” and call
your service technician or gas supplier.
9. Close pilot cover and replace casing front.
10. Turn gas control knob counterclockwise
to “ON.”
11. Turn on all electric power to the appliance (if appli-
cable).
12. Set thermostat to desired setting.
1. STOP! Read the safety information above.
2. Set thermostat to lowest setting.
3. Turn off all electric power to the appliance (if appli-
cable).
4. Push in gas control knob slightly and turn clockwise
to “OFF”.
NOTE: Knob cannot be turned from “PILOT” to “OFF”
unless knob is pushed in slightly. Do not force.
5. Waitten(10)minutes toclear outany gas. Thensmell
for gas, including near the floor. If you smell gas,
STOP! Follow “B” in the safety information above. If
you don’t smell gas, go to the next step.
PILOT
BURNER
THERMOCOUPLE

Page 8 R-2065
SERVICE AND MAINTENANCE SUGGESTIONS
SYMPTOMS - POSSIBLE CAUSES OR CORRECTION
1. Impossible to light pilot
a. If using piezo ignitor, check electrode location.
b. Remove nut at orifice and check for gas.
c. If gas available, check for blocked orifice or pilot.
2. Pilot outage
a. Proper size of pilot flame.
b. Defective or weak thermocouple.
3. Pilot flames but goes out when knob is released
a. Pilot flame not covering the thermocouple properly.
b. Defective thermocouple.
c. Defective magnet in the safety section of valve.
4. Poor thermostat control
a. Thermostat needs calibrating.
b. Defective thermostat section.
5. Noisy blower
a. Tighten blower screws.
b. Check blower wheel in the open for balance.
6. Yellow main burner flame
a. Remove main burner to check for obstructions in throat, ports
and orifices.
b. Install new main burner orifice and pilot orifice.
c. Check gas valve for leaking.
d. Open the air shutter on the main burner in order to increase the
amount of primary air.
7. Yellow pilot flame
a. Small yellow tip not objectionable.
b. Remove pilot orifice. Check and clean.
8. Pilot and main burner goes out after burning a few minutes
a. Improper venting of flue products. Relight and check for im-
proper venting.
b. Ifventedproperly,checkventsafetyswitch,replace if defective.
9. Burner flashes- back or “pops” and burnsatmainburnerorifice
a. Examine main burner for defects.
10. Inoperative blower
a. Check fan control by shorting across terminals.
b. Check for blower wheel bind by removing wheel and operating
motor.
c. Check for frozen bearings due to lack of oil.
11. On Propane Gas, if a whistling noise (resonation) occurs
a. Close the air shutter on the main burner in order to reduce the
amount of primary air.
INDEX PART
NO. NUMBER DESCRIPTION
INDEX PART
NO. NUMBER DESCRIPTION
1 662015 CONTROL KNOB
2 R-2708 PIEZO IGNITOR
3 RH-702 CONTROL ROD BRACKET
4 R-2706 ECO SWITCH
5 871018 CABLE ASSEMBLY
6 RH-812 CONTROL ROD
7 R-2701 GAS VALVE (LPG)
7 R-2700 GAS VALVE (NAT)
8 RH-811 VALVE BRACKET
9 RH-705 CASING SIDE
10 RH-708 AIR INLET BAFFLE
11 P-86-38N MAIN BURNER ORIFICE (RH-35-5
NAT)
11 742155 MAIN BURNER ORIFICE (RH-25-5
NAT)
11 742260 MAIN BURNER ORIFICE (RH-35-5
LPG)
11 742238 MAIN BURNER ORIFICE (RH-25-5
LPG)
12 P-205 MANIFOLD ASSEMBLY
13 RH-818 DIVERTER ASSEMBLY
14 RH-801 DOWN DRAFT SHIELD
15 RH-799 DIVERTER PLATE
16 DV-951 CASING TOP
17 RH-819 INNER CASING ASSEMBLY (RH-
25-5)
17 RH-822 INNER CASING ASSEMBLY (RH-
35-5) W/INSULATION
18 RH-705 CASING SIDE
19 RH-691 COMBUSTION CHAMBER
ASSEMBLY (RH-35-5)
19 RH-701 COMBUSTION CHAMBER
ASSEMBLY (RH-25-5)
20 712098 GASKET - LIGHTING HOLE
21 DV-781 LIGHTING HOLE COVER
22 DV-064 COVER PLATE
23 RH-682 CASING FRONT
24 RH-737 BURNER (RH-25-5)
24 RH-738 BURNER (RH-35-5)
25 672056 THERMOCOUPLE 36"
26 762141 PILOT BURNER WITH ORIFICE
(NAT)
26 762247 PILOT BURNER WITH ORIFICE
(LPG)
27 RH-817 PILOT TUBING WITH FERRELLS
28 732065 ELECTRODE AND WIRE
NOT SHOWN 652121 REGULATOR (NAT)
NOT SHOWN 652211 REGULATOR (LPG)
NOT SHOWN R-2738 OPERATOR/REGULATOR (NAT)
NOT SHOWN R-2739 OPERATOR/REGULATOR (LPG)
NOT SHOWN 742158 PILOT ORIFICE (NAT)
NOT SHOWN 742266 PILOT ORIFICE (LPG)
NOT SHOWN R-2707 JUNCTION BLOCK ADAPTOR/ECO
SWITCH
NOT SHOWN UH-441 VENT SAFETY SWITCH/ECO
HOLE COVER PLATE
USE ONLY MANUFACTURER’S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH.

Page 9R-2065
How To Order Repair Parts...
Partscanbe orderedonlythroughyourservicepersonordealer. Forbestresults,the servicepersonordealershouldorderpartsthroughthe distributor.
Parts can be shipped directly to the service person/dealer.
All parts listed in the Parts List have a Part Number. When ordering parts, first obtain the Model Number from the name plate on your equipment. Then
determine the Part Number (not the Index Number) and the Description of each part from the following appropriate illustration and list. Be sure to give
all this information . . .
Furnace Model Number Part Description
Furnace Serial Number Kind of Gas (Propane or Natural)
Part Number
Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store.
Shipments contingent upon strikes, fires and all causes beyond our control.
PLEASE NOTE: When ordering parts, it is very important the part number and description of part coincide.
Empire Comfort Systems, Inc. Nine Eighteen Freeburg Ave. Belleville, Illinois 62222-0529

Page 10 R-2065
OPTIONAL BLOWER DRB-1
Vented Room Heaters RH-25-(1, 2, 4, 5) and RH-35-(1, 2, 4, 5)
Direct Vent Wall Furnaces DV-25-(1, 2)SG and DV-35-(1, 2)SG
Installing Optional DRB-1 Blower
1. For RH-25-(1, 2, 4, 5) and RH-35-(1, 2, 4, 5), remove
casing front.
1. ForDV-25-(1,2)SGandDV-35-(1,2)SG,removecasing
front and heat shield.
2. When facing appliance, insert blower assembly into the
left section of the casing (adjacent to the combustion
chamber).
3. For RH-25-(1, 2, 4, 5) and RH-35-(1, 2, 4, 5), route cord
setthroughopeningin casing back. Theopening in casing
back is located adjacent to gas control.
3. For DV-25-(1, 2)SG and DV-35-(1, 2)SG, route cord set
through opening in casing bottom. The opening in casing
bottom is located beneath gas control.
4. Align the (2) screw holes on the inner side panel and the
(2)screwholesoncasingbackwiththe(4)clearanceholes
on the blower assembly. Attach blower assembly to the
casing back and inner side panel with (4) #10 x 1/2"
(13mm) screws provided. The blower assembly must be
attachedfirstto the casing backandthentothecasingside
panel.
5. For RH-25-(1, 2, 4, 5) and RH-35-(1, 2, 4, 5), replace
casing front.
5. For DV-25-(1, 2)SG and DV-35-(1, 2)SG, replace heat
shield and casing front.
Attention: Wiringharnessonblowerisfactoryassembledand
installed. If wiring harness becomes disassembled use the
following steps to reassemble the wiring harness.
1. Attach (1) pin terminal from black (hot) wire, smooth
insulation on cord set to (1) socket terminal on fan control
assembly.
2. Attach (1) pin terminal from black (neutral) wire, ribbed
insulation on cord set to (1) socket terminal from white
(neutral) wire on motor.
3. Attach (1) pin terminal on fan control assembly to (1)
socket terminal from black (hot) wire on motor.
4. Attach green ground wire beneath one of the #10 x 1/2"
(13mm) screws on the blower housing.
Fan Control
The automatic fan control is located in the switch box. The
switchboxisattachedtothefrontoftheblowerassembly. The
switch box is adjacent to the combustion chamber. The fan
control is a non-adjustable automatic type. The fan control
will require between 5 and 10 minutes of main burner opera-
tion before the fan control “closes” and activates the blower.
Theblowerwillcontinuetorunbetween5and10minutesafter
the main burner shuts off, before the fan control “opens” and
deactivates the blower.

Page 11R-2065
Wiring
The appliance, when installed, must be electrically grounded in
accordancewithlocalcodesor,intheabsenceoflocalcodes,with
the National Electrical Code, ANSI/NFPA 70 or Canadian
Electrical Code, CSA C22.1, if an external electrical source is
utilized. This appliance is equipped with a three-prong
[grounding] plug for your protection against shock hazard
and should be plugged directly into a properly grounded
three-prong receptacle. Do not cut or remove the grounding
prongfromthisplug. Foranungroundedreceptacle,anadapter,
whichhastwoprongsandawireforgrounding,canbepurchased,
pluggedintothe ungrounded receptacleand its wireconnected to
the receptacle mounting screws. With this wire completing the
ground, the appliance cord plug can be plugged into the adapter
and be electrically grounded.
CAUTION: Label all wires prior to disconnection when
servicing controls. Wiring errors can cause improper and
dangerousoperation.Verifyproperoperationafterservicing.
WARNING:
Unplugging of blower accessory will not stop the heater
fromcycling. To shutheater off: Turntemperature dial
or thermostat to lowest setting.Turn knob on gas con-
trol to “OFF”, depressing slightly. Do not force.
Cleaning
Theblowerwheelwillcollectlintandcouldrequirecleaningonce
a year. If the air output decreases or the noise level increases, it
indicates a dirty wheel. Complete removal of the wheel and
scrubbing it with a brush under flowing water is recommended.
Oiling
Theblowermotorhasanoilholelocatedoneachendofthemotor.
Use #20 motor oil only. It is best to oil the motor several times
during the heating season using 2 or 3 drops each time. If the
motorfailstostartandhums,itcouldbeatightbearingduetolack
ofoil. Thismaybecorrectedbypouringkeroseneintheoilholes,
allowing to stand for a few hours and then oiling properly.
PARTS LIST
Index Part
No. No. Description
1 R-2090 Motor
2 632016 Motor Cushion
3 RH-036 Motor Support
4 642030 Blower Wheel
5 RH-710 Blower Housing Assembly
6 9120106 Fan Control Switch
7 872087 Heyco Bushing
8 DV-806 Switch Box
9 DV-807 Switch Box Cover
10 R-2091 Wire Assembly 19" (483mm)
11 8720161 Heyco Bushing
12 R-2099 Cord Set 72" (183cm)