EMS EC-63-0001 User manual

Designated zone
and sounder circuits.
Conventional Interface Card (CIC)
Installation Guide
Part no
EC-63-0001
Product description
EMS Conventional Interface Card
1 Pre installation 2 Pre installation
!
Installation must conform to applicable local installation codes
and should only be installed by a fully trained competent person.
• Only t the CIC to the zone interface module (ZIM), when connecting to
a conventional re panel.
• The CIC should only be connected to designated zone and sounder
circuits.
• Refer to the EMS wireless zone monitor engineers guide (TSD143) for full
programming information.
• Refer to the conventional control panel compatibility document (MK58)
for details of compatible conventional re alarm panels.
• This device contains electronics that may be susceptible to damage
from Electrostatic Discharge (ESD). Take appropriate precautions when
handling electronic boards.
3 Connect CIC to the ZIM
5 Fasten the ZIM’s terminals 6 Connection wiring
©2022 EMS Ltd. All rights reserved. Page 1 of 2 TSD147-99 Issue 7 21/06/2022 AJM
Ensure the pins line up with the ZIM’s terminal connections as shown.
• The CIC can be wired in two dierent ways.
• Fault notication can either be monitored via the conventional re panel’s
sounder or zone circuit.
• See overleaf for the alternative wiring methods.
SOUNDERS FAULT ZONE/RESET
EOL L1 L2 EOL L1 L2 ALARM
RES
EOL L1 L2
(+) (-) (+) (-) (+) (-) (+) (-) (+) (-) (+) (-) (+) (-)
When tted to the zone interface module (ZIM), the conventional interface
card (CIC) enables 30 FireCell wireless devices to be added to an existing
conventional re panel, via a wireless zone monitor (WZM).
www.emsgroup.co.uk
RadioDetectorBase
PRESSHERETO
LOGON
IDENT
POWER
FAULT
WIRELESSZONEMONITOR
FC-ZIM-001
*
*
ZIM with
CIC tted WZM
Conventional
re panel
FireCell wireless devices
4 Fasten the CIC PCB into the ZIM
SOUNDERS FAULT ZONE/RESET
EOL L1 L2 EOL L1 L2 ALARM
RES EOL L1 L2
SOUNDERS FAULTZ ONE/RESET
EOL L1 L2 EOL L1 L2 ALARM
RES EOL L1 L2

ZONE
+ -
TX
RADIO
WD
RESET
HELP
RX
ON
12345678
BACK
POWER
FAULT
ISOLATE
SCR
+
-
LOOP IN
SCR
LOOP OUT
+
-
12 3 4 5 6 7
3V3
TX
RX
0V
OUTPUT 2OUTPUT 1
3VDC SETRST
INPUT1 INPUT2
LED
ENABLE
POWER
INPUT 1
INPUT 2
FAULT
CLOSED
01
1
64
F-SAFE
N/OCOM N/C
SERIALNO
LOGON
IP- IP+IP- IP+
3VDC SETRST N/OCOMN/C
EXPAN1EXPAN2
RELAYON RELAYON
2
4
8
16
32
ANTENNA
KEEPCABLES AWAY FROM THIS AREA
SOUNDERFAULT ZONE
EOL L1L2EOL L1 L2 ALARM
RES
EOL L1L2
(+) (-) (+) (-) (+) (-) (+) (-) (+) (-) (+) (-) (+) (-)
SOUNDERS FAULT ZONE/RESET
EOL L1 L2 EOL L1 L2 ALARM
RES
EOL L1 L2
(+) (-) (+) (-) (+) (-) (+) (-) (+) (-) (+) (-) (+) (-)
LOOP IN
24V OUT
- +
SOUNDER
+ -
13
2
+ -
6 Connection wiring continued 6 Connection wiring continued
Specication Regulatory information
©2022 EMS Ltd. All rights reserved. Page 2 of 2 TSD147-99 Issue 7 21/06/2022 AJM
Option 1
Wired to provide fault
notication on the
conventional re panel’s
SOUNDER CIRCUIT
Operating temperature -10 to +55 °C
Storage temperature 5 to 30 °C
Humidity 0 to 95% non-condensing
Supply Powered from the zone interface monitor
Current drawn from
connected panel (max.) 6 mA
Voltage (max.) 50 VDC
IP rating IP65
(when tted inside zone interface monitor)
Dimensions (W x H x D) 120 x 240 x 60 mm
Weight 0.95 kg
Location Type A: For indoor use
Manufacturer
Year of manufacture
Certication
Certication body
CPR DoP
Approved to
European Union
Directives
0359-CPR-00436
EN54-18:2005. Fire detection and re alarm systems.
Part 18:Input/output devices.
EMS declares that this device is in compliance with Directive
2014/53/EU. The full text of the EU declaration of conformity
is available at the following internet address: www.
emsgroup.co.uk
2012/19/EU (WEEE directive): Products marked with this
symbol cannot be disposed of as unsorted municipal waste
in the European Union. For proper recycling, return this
product to your local supplier upon purchase of equivalent
new equipment, or dispose of it at designated collection
points. For more information see www.recyclethis.info
Dispose of your batteries in an environmentally friendly
manner according to your local regulations.
Carrier Manufacturing Poland Sp. z o.o.
Ul. Kolejowa 24. 39-100 Ropczyce, Poland
See devices serial number label
0905
14
Zone interface monitor (ZIM)
with conventional interface
card (CIC) tted
Wireless
zone monitor
(WZM)
Conventional re panel
1= Sounder circuit EOL resistor
2= Alarm triggering resistor
3= Zone circuit EOL resistor
TX
RADIO
WD
RESET
HELP
RX
ON
12345678
BACK
POWER
FAULT
ISOLATE
SCR
+
-
LOOP IN
SCR
LOOP OUT
+
-
12 3 4 5 6 7
3V3
TX
RX
0V
+ -
OUTPUT 2OUTPUT 1
3VDC SETRST
INPUT1 INPUT2
LED
ENABLE
POWER
INPUT 1
INPUT 2
FAULT
CLOSED
01
1
64
F-SAFE
N/OCOMN/C
SERIALNO
LOGON
IP- IP+ IP- IP+
3VDCSET RST N/OCOMN/C
EXPAN1 EXPAN2
RELAYON RELAYON
2
4
8
16
32
ANTENNA
KEEPCABLES AWAY FROM THIS AREA
SOUNDERFAULT ZONE
EOL L1L2 EOL L1L2 ALARM
RES
EOLL1L2
(+) (-)(+) (-)(+) (-) (+) (-) (+) (-)(+) (-)(+) (-)
SOUNDERS FAULT ZONE/RESET
EOL L1 L2 EOL L1 L2 ALARM
RES
EOL L1 L2
(+) (-) (+) (-) (+) (-) (+) (-) (+) (-) (+) (-) (+) (-)
24V OUT
- +
SOUNDER
+ -
ZONE
+ -
13
2
LOOP IN
Option 2
Wired to provide fault
notication on the
conventional re panel’s
ZONE CIRCUIT
Zone interface monitor (ZIM)
with conventional interface
card (CIC) tted
Wireless
zone monitor
(WZM)
Conventional re panel
1= Sounder circuit EOL resistor
2= Zone circuit EOL resistor
3= Alarm triggering resistor