Emulex OneConnect OCe14000-Series User manual

P009818-03A Rev. A Connect • Monitor • Manage
OneConnect®
OCe14000-Series Adapters
Installation Manual

OneConnect OCe14000-Series Adapters Installation Manual P009818-03A Rev. A
2
Copyright © 2013–2015 Emulex. All rights reserved worldwide. No part of this document may be reproduced by any
means or translated to any electronic medium without the prior written consent of Emulex.
Information furnished by Emulex is believed to be accurate and reliable. However, no responsibility is assumed by
Emulex for its use; or for any infringements of patents or other rights of third parties which may result from its use. No
license is granted by implication or otherwise under any patent, copyright or related rights of Emulex.
Emulex, the Emulex logo, Emulex BladeEngine, Emulex InSpeed, Emulex LightPulse, Emulex OneCommand, Emulex
OneConnect, and SLI are registered trademarks, and Emulex Advanced-8, Emulex Connect, Emulex CrossLink,
Emulex Engine, Emulex Edge, Emulex ExpressLane, Emulex GreenState, Network Xceleration, Emulex OneCore,
Emulex Pilot, Emulex SURF, Emulex Universal Multi-Channel, Emulex vEngine, Emulex Virtual Fabric, Emulex
Virtual Network Exceleration, Emulex vPath, Emulex vScale, AutoPilot, AutoPilot Installer, and BlockGuard are
trademarks, of Emulex. All other brands or product names referenced herein are trademarks or registered trademarks
of their respective companies or organizations.
Emulex provides this manual "as is" without any warranty of any kind, either expressed or implied, including but not
limited to the implied warranties of merchantability or fitness for a particular purpose. Emulex may make
improvements and changes to the product described in this manual at any time and without any notice. Emulex
assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties that may
result. Periodic changes are made to information contained herein; although these changes will be incorporated into
new editions of this manual, Emulex disclaims any undertaking to give notice of such changes.
Emulex, 3333 Susan Street
Costa Mesa, CA 92626

OneConnect OCe14000-Series Adapters Installation Manual P009818-03A Rev. A
Table of Contents 3
Table of Contents
List of Figures ......................................................................................4
List of Tables .......................................................................................5
1. Introduction.....................................................................................6
Features.................................................................................................9
General Features..................................................................................9
OCe14101 Adapters..................................................................................10
OCe14102 Adapters..................................................................................10
OCe14104 Adapters..................................................................................10
Protocol-Specific Capabilities......................................................................11
Adapter Identification.............................................................................. 12
Abbreviations ........................................................................................ 12
2. Installation.....................................................................................14
Preparing the Adapter for Installation.......................................................... 14
Installing the Adapter .............................................................................. 16
3. Attaching Devices to the Adapter.........................................................17
Connecting Devices to Adapters Using a DAC or AOC Cable ................................ 17
Emulex OneConnect Accessories ..............................................................19
Connecting Devices to Adapters Using an Optical Cable with LC Connectors........... 20
Connecting Devices to Adapters Using a UTP or CAT Cable ................................ 22
4. Applying Power and Viewing the LEDS...................................................23
Applying Power ...................................................................................... 23
LED Indicators........................................................................................ 23
For the OCe14102-NT/UT Adapter ............................................................23
For All Other OCe14000-series Adapters .....................................................23
Viewing the LEDs.................................................................................... 23
5. References ....................................................................................26
Specifications ........................................................................................ 26
FCC and Regulatory Notices....................................................................... 27
Declarations of Conformity........................................................................ 29
Laser Safety Notice ................................................................................. 30

OneConnect OCe14000-Series Adapters Installation Manual P009818-03A Rev. A
List of Figures 4
List of Figures
Figure 1-1 Emulex OCe14102 Adapter ...............................................................8
Figure 1-2 Emulex OCe14102-NT/UT Adapter ......................................................8
Figure 1-3 Emulex OCe14401 Adapter ...............................................................9
Figure 2-1 Optical Transceiver Example............................................................14
Figure 2-2 Releasing the Latch on an Optical Transceiver.......................................15
Figure 2-3 Removing the Bracket....................................................................15
Figure 3-1 Connecting a DAC Cable to the OCe14100-series -NX/-UX Adapters..............18
Figure 3-2 Connecting a DAC Cable to the OCe14100-series -NX/-UX Adapters..............18
Figure 3-3 Installing an Optical Transceiver for the OCe14000-series -NM/-UM
Adapters....................................................................................21
Figure 3-4 Connecting a Fiber Optic Cable for the OCe14000-series -NM/-UM
Adapters....................................................................................21
Figure 4-1 OCe14101-NM/-NX, OCe14102-NM/-NX, and OCe14102-UX/-UM Adapter
LED Indicators .............................................................................24
Figure 4-2 OCe14401-NX/-UX Adapter LED Indicators............................................24
Figure 4-3 OCe14102-NT and OCe14102-UT LED Indicators......................................25
Figure 4-4 OCe14104-NM/-UM LED Indicators......................................................25

OneConnect OCe14000-Series Adapters Installation Manual P009818-03A Rev. A
List of Tables 5
List of Tables
Table 1-1 OCe14000-series Adapters ................................................................6
Table 3-1 OCe14101-NX, OCe14102-NX/-UX, and OCe14104-NX/-UX Cable and
Connector Specifications.................................................................17
Table 3-2 OCe14401-NX/-UX Cable and Connector Specifications.............................17
Table 3-3 OCe14101-NX, OCe14102-NX, and OCe14104-NX/-UX Adapter Emulex
OneConnect Accessories .................................................................19
Table 3-4 OCe14401-NX/UX Adapter Emulex OneConnect Accessories .......................19
Table 3-5 OCe14101-NM, OCe14102-NM/-UM, and OCe14104-NM/-UM Adapter Cable
and Connector Specifications ...........................................................20
Table 3-6 OCe14102-NT/-UT Adapter Cable and Connector Specifications ..................22
Table 5-1 Adapter Specifications ...................................................................26

OneConnect OCe14000-Series Adapters Installation Manual P009818-03A Rev. A
1. Introduction 6
1. Introduction
This manual describes the following Emulex®OneConnect®OCe14000-series of
multi-protocol Peripheral Component Interconnect Express (PCIe) adapters that
provide Ethernet networking, RDMA over Converged Ethernet (RoCE), internet Small
Computer System Interface (iSCSI) functionality, and Fibre Channel over Ethernet
(FCoE) functionality for convergence of Fibre Channel (FC) traffic onto a Ethernet
fabric.
Table 1-1 lists the OCe14000-series adapters.
Table 1-1 OCe14000-series Adapters
Adapter
Models Number of Ports Supported Protocols Cable Type
OCe14101-NX 1x10GbE NIC
RoCE 10GbE SFP+ Passive Direct-attach Copper
(DAC) Cable
10GbE SFP+ Active DAC Cable
10GbE SFP+ Active Optical (AOC) Cable
OCe14101-NM 1x10GbE NIC
RoCE 10GbE SFP+ fiber optic cable with LC
connector
OCe14102-NX 2x10GbE NIC
RoCE 10GbE SFP+ Passive DAC Cable 10GbE SFP+ Active DAC Cable
10GbE SFP+ AOC Cable
OCe14102-UX 2x10GbE NIC
RoCE
iSCSI
FCoE
OCe14102-NM 2x10GbE NIC
RoCE 10GbE SFP+ fiber optic cable with LC
connector
OCe14102-UM 2x10GbE NIC
RoCE
iSCSI
FCoE
OCe14102-NT 2x10GbE NIC
RoCE Unshielded twisted pair (UTP) copper Shielded twisted pair (STP) copper
OCe14102-UT 2x10GbE NIC
RoCE
iSCSI
FCoE

OneConnect OCe14000-Series Adapters Installation Manual P009818-03A Rev. A
1. Introduction 7
OCe14104-NX 4x10GbE NIC
RoCE 10GbE SFP+ Passive DAC Cable 10GbE SFP+ Active DAC Cable
10GbE SFP+ AOC Cable
OCe14104-UX 4x10GbE NIC
RoCE
iSCSI
FCoE
OCe14104-NM 4x10GbE NIC
RoCE 10GbE SFP+ fiber optic cable with LC
connector
OCe14104-UM 4x10GbE NIC
RoCE
iSCSI
FCoE
OCe14401-NX 1x40GbE NIC
RoCE 40GbE QSFP+ Passive DAC Cable 40GbE QSFP+ Active DAC Cable
OCe14401-UX 1x40GbE NIC
RoCE
iSCSI
FCoE
Table 1-1 OCe14000-series Adapters (Continued)
Adapter
Models Number of Ports Supported Protocols Cable Type

OneConnect OCe14000-Series Adapters Installation Manual P009818-03A Rev. A
1. Introduction 8
Note: Illustrations in this manual are only examples. The actual hardware may vary.
Figure 1-1 Emulex OCe14102 Adapter
Figure 1-2 Emulex OCe14102-NT/UT Adapter

OneConnect OCe14000-Series Adapters Installation Manual P009818-03A Rev. A
1. Introduction
Features 9
Figure 1-3 Emulex OCe14401 Adapter
All Emulex adapters support NIC single root I/O virtualization (SR-IOV) and are fully
compliant to the PCIe Card Electromechanical (CEM) Specification Rev. 3.0/2.0/1.1.
Converged network adapters (CNAs) combine two major functional components: a
10GbE networking media access control (MAC) sublayer and an FC I/O controller
(IOC) to interface with a unified lossless Ethernet switch. Adapters serve as a common
interface for both storage and Internet Protocol (IP) traffic retaining familiar FC and
networking software stacks, OS drivers, and management. The supported Peripheral
Component Interconnect Express (PCIe) connector is an x8 or x16.
Features
General Features
Eight-lane (x8) Generation 3 PCIe interface at 8GT/s, 5GT/s, or 2.5GT/s
(auto-negotiated with system)
Parts and construction are compliant to the European Union Directive of RoHS,
and similar regulatory requirements for other countries.
Comes with a standard, full height I/O bracket installed. The standard,
full-height form factor is 6.600 inches by 4.3760 inches (167.64 mm by 111.15
mm); for low–profile adapters, an optional low–profile I/O bracket is included.
The low-profile PCIe form factor PCBA is 6.600 inches by 2.713 inches (167.64
mm by 68.910mm).
External volatile memory: 2GB/4GB DDR3 SDRAM technology
On-board flash memory: The flash is 128Mbit with a SPI interface. The flash
contains the firmware, VPD, and Boot BIOS images. You can update the flash
with Emulex utilities.
Interoperates with existing FC SAN infrastructures – switches, arrays, SRM
tools (including Emulex utilities), SAN practices, and so forth.

OneConnect OCe14000-Series Adapters Installation Manual P009818-03A Rev. A
1. Introduction
Features 10
Host interface support is provided through Emulex standard drivers
Support for RoCE NIC operating system drivers (Windows Server and Linux
OFED)
As supported, a comprehensive array of NIC, iSCSI, FCoE, operating system
drivers, including support for Windows, Linux, VMware, and Solaris.
As supported, Unified Ethernet-to-FC SAN connectivity provided by an FCoE
switch.
OCe14101 Adapters
Up to eight PCIe functions per adapter, individually configurable to NIC and
RoCE personalities.
Low-profile PCIe form factor
OCe14101-NM - SFF-8431 Small Form Factor Pluggable Module SFP+ compliant
OCe14102 Adapters
Up to sixteen PCIe functions per adapter
OCe14102-NX/-NM/-NT - individually configurable to NIC and RoCE
personalities
OCe14102-UX/-UM/-UT - individually configurable to NIC, RoCE, iSCSI,
or FCoE personalities
Low-profile PCIe form factor
OCe14102-NM/-UM - SFF-8431 Small Form Factor Pluggable Module SFP+
compliant
OCe14104 Adapters
Up to sixteen PCIe functions per adapter
OCe14104-NX/-NM - individually configurable to NIC and RoCE
personalities
OCe14104-UX/-UM - individually configurable to NIC, RoCE, iSCSI, or
FCoE personalities
Standard, full-height form factor only
OCe14104-NM/-UM - SFF-8431 Small Form Factor Pluggable Module SFP+
compliant
OCe14401 Adapters
OCe14101-NX and the OCe14101-NM adapters support eight functions
Up to sixteen PCIe functions per adapter, if the system supports ARI
OCe14401-NX - individually configurable to NIC and RoCE personalities
OCe144041-UX - individually configurable to NIC, RoCE, iSCSI, or FCoE
personalities
Low-profile PCIe form factor
SFF-8436 compliant QSFP+ interface supporting optics and direct attach cables

OneConnect OCe14000-Series Adapters Installation Manual P009818-03A Rev. A
1. Introduction
Features 11
Protocol-Specific Capabilities
NIC capabilities include
NDIS 5.2, 6.0, and 6.2-compliant Ethernet functionality
IPv4/IPv6 TCP, UDP checksum offload
IPv4/IPv6 RSS
IPv4/IPv6 LRO
IPv4/IPv6 LSO
Programmable MAC addresses
Up to 128 MAC/VLAN addresses
Supports hash-based multicast MAC address filters
Supports hash-based broadcast frame filters per port
VLAN insertion and extraction
Jumbo packet support up to 9000 bytes
iSCSI capabilities include
Full iSCSI protocol offload
Header, data digest (CRC), and PDUs
Direct data placement of SCSI data
Up to 4K outstanding commands (iSCSI initiator mode only)
Up to 512 offloaded iSCSI connections (iSCSI initiator mode only)
iSCSI initiator and concurrent initiator/target modes
Supports multipath I/O
T10 PI support for end-to-end data integrity (for target mode drivers)
FCoE capabilities include
Hardware offloads of Ethernet TCP/IP and concurrent iSCSI and FCoE
ANSI T11 FC-BB-5 support
Programmable WWN
Supports FIP and FCoE ether types
Concurrent logins (RPI): up to 8K per adapter
Open exchanges (XRI): up to 4K per adapter
FCoE initiator and target modes
NPIV Interfaces:
For 2x10GbE and 1x40GbE adapters, up to 255 NPIV interfaces per port
For the 4x10GbE adapter, up to 127 NPIV interfaces per port
T10 PI support for end-to-end data integrity (for target mode drivers)
RoCE capabilities include
Direct data placement in application buffers without CPU intervention
Supports IBTA RoCE specifications
Supports Linux Open Fabrics Enterprise Distribution (OFED)
Low latency queues for small packet sends and receives

OneConnect OCe14000-Series Adapters Installation Manual P009818-03A Rev. A
1. Introduction
Adapter Identification 12
Windows Server SMB Direct (SMB over RDMA)
Adapter Identification
Each adapter ships with several numbers clearly marked on the board. Emulex
recommends recording these numbers before installation.
Institute of Electrical and Electronics Engineers (IEEE) address – a unique 64-bit
identifier used for system configuration
WWN – derived from the IEEE address; the FC industry uses the WWN for FC
connectivity.
Serial number – assigned by Emulex and used when communicating with
Emulex
If the adapter has two ports, it has two IEEE addresses and two WWNs, one for each
port.
Abbreviations
AOC active optical cable
ARI alternative routing-ID interpretation
CNA Converged Network Adapter
CPU central processing unit
CRC cyclic redundancy check
DAC direct-attach copper
DDR3 double data rate type three
ESD Electrostatic Discharge
FC Fibre Channel
FCoE Fibre Channel over Ethernet
FIP FCoE Initialization Protocol
GB gigabyte
Gb gigabit
GbE gigabit Ethernet
Gbps gigabits per seconds
GT/s gigatransfers per second
IBTA InfiniBand Trade Association
IEEE Institute of Electrical and Electronics Engineers
IOC I/O controller
IP Internet Protocol
iSCSI Internet Small Computer System Interface
LED light-emitting diode

OneConnect OCe14000-Series Adapters Installation Manual P009818-03A Rev. A
1. Introduction
Abbreviations 13
LRO large receive offload
LSO large segment offload
MAC Media Access Control
Mbit megabit
mm millimeters
NDIS Network Driver Interface Specification
NIC network interface card
NPIV N_Port ID Virtualization
OFED OpenFabrics Enterprise Distribution
PCBA printed circuit board assembly
PCIe Peripheral Component Interconnect Express
PCIe CEM PCIe Card Electromechanical
PDU protocol data unit
POST power-on self-test
QSFP+ Quad Small Form Factor Pluggable
RDMA remote direct memory access
RH relative humidity
RoCE RDMA over Converged Ethernet
RoHS Restriction of Hazardous Substances
RSS receive-side scaling
SAN storage area network
SDRAM synchronous dynamic random-access memory
SFP small form-factor pluggable
SMB server message block
SPI Serial Peripheral Interface
SR-IOV single root I/O virtualization
SRM storage resource management
T10 PI T10 Protection Information
TCP Transmission Control Protocol
TOR top of rack
UDP User Datagram Protocol
VLAN virtual local area network
vNIC virtual network interface card
VPD vital product data
WWN World Wide Name

OneConnect OCe14000-Series Adapters Installation Manual P009818-03A Rev. A
2. Installation
Preparing the Adapter for Installation 14
2. Installation
This section provides information on converting from the standard bracket to a
low-profile adapter bracket, if applicable, and installing the adapter in a computer.
Preparing the Adapter for Installation
A standard, full-height PCIe bracket is installed. A low-profile bracket is included in
the box with the adapter (except for the OCe14104 adapter, which cannot use the
low-profile bracket).
If you want to change the bracket to the low-profile version, follow the procedure in
this section; otherwise, proceed to “Installing the Adapter” on page 16.
To change the bracket:
1. Some adapters come with optical transceivers embedded in their cage assemblies.
These optical transceivers must be removed before the bracket can be removed. If
the adapter does not include optical transceivers, skip to step 4.
The low-profile mounting bracket is shorter than the standard bracket;
approximately 3.11 in. (7.9 cm) compared to 4.75 in. (12.06 cm) long.
Caution: This is a delicate operation–take care not to damage the optical
transceiver.
The adapter uses different types of optical transceivers. Figure 2-1 on page 14
shows an example of one type with the bail (handle) extended.
Figure 2-1 Optical Transceiver Example
2. To remove a transceiver, pull the bail (handle) out and down to release the latch
and gently pull the transceiver out. Do not force it. After the latch is released, the
transceiver slides out easily.

OneConnect OCe14000-Series Adapters Installation Manual P009818-03A Rev. A
2. Installation
Preparing the Adapter for Installation 15
Figure 2-2 on page 15 shows a transceiver with the latch released (bail extended)
and another transceiver latched in place.
Figure 2-2 Releasing the Latch on an Optical Transceiver
3. Observing ESD precautions, store the transceiver in an ESD-safe place.
4. Remove the mounting bracket screws from the top of the adapter. Figure 2-3 on
page 15 shows the screws that are removed from the bracket.
Figure 2-3 Removing the Bracket
5. Remove the bracket and store it for future use.
6. Align the new mounting bracket tabs with the holes in the adapter.
Note: For some adapters, be careful not to push the bracket past the transceiver.
Ensure that the LEDs are properly aligned with the holes in the bracket.
7. Re-install the screws that attach the adapter to the bracket.
8. Re-install the transceiver, if it was removed, by sliding it into the housing. When the
latch engages, it clicks. Push the bail back into place.

OneConnect OCe14000-Series Adapters Installation Manual P009818-03A Rev. A
2. Installation
Installing the Adapter 16
Installing the Adapter
To install the adapter in the computer, perform the following steps:
1. Turn off the computer and unplug it.
2. Remove the computer case.
3. Remove the blank panel from an empty PCIe bus slot.
4. Insert the adapter into the empty x8 or x16 PCIe bus slot. Press firmly until the
adapter is seated.
5. Secure the adapter's mounting bracket to the case with a panel screw or clip.
6. Replace the computer case and tighten the case screws.
The adapter is now installed in the server and is ready to be attached to devices.

OneConnect OCe14000-Series Adapters Installation Manual P009818-03A Rev. A
3. Attaching Devices to the Adapter
Connecting Devices to Adapters Using a DAC or AOC Cable 17
3. Attaching Devices to the Adapter
An adapter does not allow normal data transmission on a copper link, unless it is
connected to a compatible copper interface connection. The following sections describe
how to connect devices to the adapter using different cable types.
Connecting Devices to Adapters Using a DAC or AOC
Cable
The following adapters can be connected to a DAC or AOC cable:
OCe14101-NX
OCe14102-NX
OCe14102-UX
OCe14104-NX
OCe14104-UX
OCe14401-NX
OCe14401-UX
The cable and connector specifications are listed in Table 3-1 on page 17 and Table 3-2
on page 17.
To attach devices to the adapter:
1. Connect the cable to the adapter. When connecting a DAC or AOC cable, ensure
that the SFP+ cages do not have optical transceivers installed in them. To remove
optical transceivers, see “Preparing the Adapter for Installation” on page 14.
2. After confirming that there are no optical transceivers installed, insert the DAC or
AOC transceiver into the SFP+ cage on the OCe14100-series adapter as shown in
Table 3-1 OCe14101-NX, OCe14102-NX/-UX, and OCe14104-NX/-UX Cable and Connector Specifications
Cable Type Maximum Length
(meters) Minimum Length (meters) Connector
10GbE SFP+ Passive DAC Cable 5 0.5 DAC
10GbE SFP+ Active DAC Cable 10 0.5 DAC
10GbE SFP+ Active Optical Cable 7 1 AOC
Table 3-2 OCe14401-NX/-UX Cable and Connector Specifications
Cable Type Maximum Length
(meters) Minimum Length (meters) Connector
40GbE QSFP+ Passive DAC Cable 5 0.5 DAC
40GbE QSFP+ Active DAC Cable 10 0.5 DAC

OneConnect OCe14000-Series Adapters Installation Manual P009818-03A Rev. A
3. Attaching Devices to the Adapter
Connecting Devices to Adapters Using a DAC or AOC Cable 18
Figure 3-1 on page 18 or the OCe14400-series adapter as shown in Figure 3-2 on
page 18.
Figure 3-1 Connecting a DAC Cable to the OCe14100-series -NX/-UX Adapters
Figure 3-2 Connecting a DAC Cable to the OCe14100-series -NX/-UX Adapters
3. After the cable is connected to the adapter, connect the other end of the cable to a
suitable device, such as a TOR switch.
After the device is connected to the adapter, you are ready to apply power to the
computer. See “Applying Power” on page 23.
After the device is powered on, you can view the LED indicators. See “Viewing the
LEDs” on page 23.

OneConnect OCe14000-Series Adapters Installation Manual P009818-03A Rev. A
3. Attaching Devices to the Adapter
Connecting Devices to Adapters Using a DAC or AOC Cable 19
Emulex OneConnect Accessories
Table 3-3 on page 19 and Table 3-4 on page 19 provide model number, name, interface,
and required quantities, if you want to order additional or replacement transceivers or
cables.
Notes
For optical adapter support, you must order either a short reach optical adapter
model (-NM or -UM) or a direct attach model with an Emulex OneConnect
accessory transceiver kit.
Only Emulex accessories are warranted and fully supported by Emulex
Technical Support.
Table 3-3 OCe14101-NX, OCe14102-NX, and OCe14104-NX/-UX Adapter Emulex OneConnect Accessories
Model Number Model Name Quantity Interface
OC10-SR-OPT-1 Emulex OneConnect 10Base-SR
Optical SFP+ Transceiver 1 pc 10GBASE-SR Optical
OC10-SR-OPT-2 Emulex OneConnect 10Base-SR
Optical SFP+ Transceivers (2 pcs) 2 pcs 10GBASE-SR Optical
OC10-LR-OPT-1 Emulex OneConnect 10Base-LR
Optical SFP+ Transceiver 1 pc 10GBASE-LR Optical
Table 3-4 OCe14401-NX/UX Adapter Emulex OneConnect Accessories
Model Number Model Name Quantity Interface
OC40-SR4-OPT-1 Emulex OneConnect 40Base-SR4
Optical QSFP+ Transceiver 1 pc 40Gbase-SR4 Optical

OneConnect OCe14000-Series Adapters Installation Manual P009818-03A Rev. A
3. Attaching Devices to the Adapter
Connecting Devices to Adapters Using an Optical Cable with LC Connectors 20
Connecting Devices to Adapters Using an Optical
Cable with LC Connectors
The following adapters can be connected to a fiber optic cable with an embedded
optical transceiver:
OCe14101-NM
OCe14102-NM
OCe14102-UM
OCe14104-NM
OCe14104-UM
The cable and connector specifications are listed in Table 3-1 on page 17. For AOC
cables see Table 3-6 on page 22.
Table 3-5 OCe14101-NM, OCe14102-NM/-UM, and OCe14104-NM/-UM Adapter Cable and Connector
Specifications
Cable Type Maximum
Length (meters) Minimum Length (meters) Connector
Fiber Optic Cable (Ethernet Only)
Long Range, LC-LC Singlemode Fiber (SMF)
10 Gb per second (Gbps)
10,000 2 LC
OM3 – Multimode 50/125 micron fiber (2000
MHz*km bandwidth cable) with LC connectors:
1 Gbps (Not specified by IEEE 802.3)
10 Gbps 550 300 2 2LC LC
OM2 - Multimode 50/125 micron fiber (500
MHz*km bandwidth cable) with LC connectors:
1 Gbps
10 Gbps 550 82 2 2LC LC
OM1 - Multimode 62.5/125 micron fiber (200
MHz*km bandwidth cable) with LC connectors:
1 Gbps
10 Gbps 275 26 2 2LC LC