EMX IRB-325 User manual

EMX Industries, Inc. Tech support: 216-834-0761 1/4
IRB-325_Rev2.0_102219 [e-mail]
IRB-325™
UL325 Thru Beam Photoeye
Instruction Manual
The IRB-325 thru beam photoeye is an external entrapment protection device type B1, non-contact sensor
for use with automatic gates and doors. The photoeye provides a signal to the gate or door operator
that the beam is or is not obstructed. The IRB-325 operates up to 65 feet and is UL325 compliant
with operators that require normally closed (NC) monitoring.
Cautions and Warnings
This product is an accessory or part of a system. Install the IRB-325 according to
instructions from the gate or door operator manufacturer. Comply with all applicable codes
and safety regulations.
Specifications
Ordering Information
•IRB-325 Thru beam photoeye
•IRB-325-HD Protective hood, gray powder coated steel, set of two
•IRB-325-SP Liquid tight strain relief connector, nylon, set of two
•IRB-325-PT Mounting post, black powder coated steel, 2” x 2” x 2’
Operating Range
Up to 65 ft (20 m)
Power
12-24 VDC/AC
ononly)
Current
150 mA (relay activated)
Relay Contact Rating
1 A @ 30 VDC
Surge Protection
Thermal fuse
Relay Output
Form C contacts (NO, COM, NC)
Operating Temperature
-40° to 170°F (-40° to 77°C)
Dimensions (L x W x H)
3.2” (82 mm) x 3.06” (78 mm) x 5.03” (128
mm)
Environmental Rating
NEMA 4X
TM

EMX Industries, Inc. Tech support: 216-834-0761 2/4
IRB-325_Rev2.0_102219 [e-mail]
Board Diagram
1. Detect LED (red)
Aligned or No Detection
off
Not Aligned or Beam Blocked
on
Imperfect Alignment
one on, one off
2. Power LED (green)
Power
on
No Power
off
3. Sensitivity Jumper
The IRB-325 has three sensitivity settings: high, medium or low. To adjust the sensitivity,
move both jumpers to the desired high, medium or low setting.
4. Terminal Block
The power inputs on both the receiver and transmitter are not polarity sensitive.
Receiver Terminal Block
Transmitter Terminal Block
Normally Closed
NC
12-24 VDC/AC
Power Input
Common
COM
12-24 VDC/AC
Power Input
Normally Open
NO
12-24 VDC/AC
Power Input
12-24 VDC/AC
Power Input
Receiver
Transmitter

EMX Industries, Inc. Tech support: 216-834-0761 3/4
IRB-325_Rev2.0_102219 [e-mail]
Installation
•Determine the mounting location of the IRB-325 photoeye according to UL325 guidelines.
•Deactivate the gate or door during photoeye installation.
1. Thread all wires through a UL listed watertight fitting, such as a strain relief or watertight conduit
connector.
2. Connect 12-24 VDC/AC power to the “Power Input”terminals on the transmitter (marked “TX”)
and receiver (marked “RX”). The power input terminals are not polarity sensitive.
3. Wire the receiver’s relay contacts to the operator. For operators that require normally closed
contacts, connect terminals NC and COM to the designated terminals. For operators that require
normally open contacts, connect terminals COM and NO to the designated terminals.
4. Verify that the IRB-325 transmitter and receiver are aligned and apply power.
The green power LED should be on for both the transmitter and receiver.
5. The receiver and transmitter are aligned properly when both red LEDs on the receiver are off.
If necessary, adjust the sensitivity by moving the jumpers (J1 and J2) up to increase and
down to decrease. Both jumpers should be on the same high, medium or low setting.
A close but imperfect alignment will have one red LED turned on.
6. Mount the receiver and transmitter at
opposite ends of the detection zone using
the four holes on the housing.
After mounting, seal the housing using
the cover and the four plastic screws
provided to ensure a watertight seal.
7. Place an obstruction (ex. hand) between the IRB-325 transmitter and receiver. Both red LEDs on
the receiver will turn on. Check the operator control board and verify that the safety input is
recognized by the operator. Test the beam with an obstruction between transmitter and
receiver at multiple distances to confirm proper operation.
8. Remove the obstruction and both red LEDs will turn off.
If the IRB-325 is aligned but not detecting an obstruction, consider adjusting the sensitivity
on the receiver until an obstruction is detected. This may be applicable for installations
with a detection zone of less than 20 ft.
TIP:
TIP:
cover screws
mounting screws

EMX Industries, Inc. Tech support: 216-834-0761 4/4
IRB-325_Rev2.0_102219 [e-mail]
Troubleshooting
Symptom
Possible Cause
Solution
Does not detect obstruction
Sensitivity is too high
Signal is reflecting off another
surface
Move jumpers J1 and J2 to a lower
position.
Check area for highly reflective
surfaces.
Red LEDs on
Sensitivity is too low
Transmitter does not have
power
Receiver does not “see”
transmitter
Move jumpers J1 and J2 to a higher
position.
Check power source to transmitter.
Make sure transmitter and receiver
are correctly aligned.
Receiver detects intermittently
with no obstruction present
Dirty power
Using the two ceramic disk caps
provided –
1. On the receiver, place a lead
from disk cap 1 into the first
power terminal.
2. Place a lead from disk cap 2
into the second power
terminal.
3. Connect the free leads of
disk caps 1 and 2 and attach
them to an earth ground.
Receiver activates but does not
transmit signal to operator
Faulty connection between
receiver and operator control
input
Verify all wire and terminal
connections.
Warranty
EMX Industries, Inc. products have a warranty against defects in materials and workmanship for a period
of two years from date of sale to our customer.