ENDA ET2011 User manual

230V AC +%10 -%20, 50/60Hz 24V AC %10, 50/60Hzor
Max. 5VA
Power : , Si : 1 ²connector 2.5mm²' screw-terminal gnal connector ,5mm screw-terminal conenction.
EEPROM ( )minimum 10 years
Max. 100ohm
1 bit2
00ms1
R : 250V AC, 8A (for resistive load), Selectable as NO+NC Control or Alarm2 output.elay
°C
Withot load 30.000.000 mechanical operation; 250V AC, on the 8A resistive load 100.000
electrical switching
C/A2 output
ENDA ET2011 PID TEMPERATURE CONTROLLER
* x mm .77 35 sized
Thank you for choosing 2011 temperature controller.ENDA ET
TECHNICAL SPECIFICATIONS
* Selectable dual-set value.
* Se tlectable thermocouple ypes or Pt100 input.(Selection must be
* Soft-Start feature.
* (SELF TUNE).Automatic calculation of PID parameters.
* Selectable heating/cooling control.
* C/A2 Relay output can be programmable as alarm or control output.
* .Selectable SSR control output
* Input offset feature.
* In the case of sensor failure periodical running or relay state can be
selected.
* .CE marked according to European Norms
Input type Temperature range
J (Fe-CuNi) Thermocouple
K (NiCr-Ni) Thermocouple
T (Cu-CuNi) Thermocouple
S (Pt 0Rh-Pt) T1 hermocouple
R (Pt13Rh-Pt) Thermocouple
EN 60584
EN 60584
EN 60584
EN 60584
EN 60584
0... 600
0...1300
0... 400
0...1700
0...1700
°C
°C
°C
°C
°C
Accuracy
0, % ( )5 of full scale
0, % ( )5 of full scale
1 digit
1 digit
0, % ( )5 of full scale 1 digit
0, % ( )5 of full scale 1 digit
0, % ( )5 of full scale 1 digit
+32... +1112
+32... +2 237
+32... +752
+32... +3092
+32... +3092
°F
°F
°F
°F
°F
°C °F
SSR output Max 20mA 12Volt (as control output)
SET
°C
SET
ET2011
ENDA
°F C/A2 SSR
F
Pt 100 Resistance thermometer
Pt 100 Resistance thermometer
EN 60751
EN 60751 -200...600 °C -328...1112 °F
- ... 00 °C99.9 3 .0 - ...543 °F99.9 .0
0,5% (of full scale) 1 digit
0,5% (of full scale) 1 digit
specified in order).
Enter PID parameters of the system if they are known at the beginning.
Otherwise, Self-Tune should be activated.
ENVIRONMENTAL CONDITIONS
Height Max. 2000m
80 up to 31 decreasing linearly 50 at 40.% %
Ambient/storage temperature
Max. Relative humidity
0 ... +50 /°C -25... +70°C (with no icing)
Rated pollution degree According to EN 60529 Front panel : IP65
Rear panel : IP20
Do not use the device in locations subject to corrosive and flammable gases.
OUTPUTS
Life expectancy for relay
ELECTRICAL CHARACTERISTICS
Supply
Power consumption
Wiring
Line resistance
Data retention
EMC
Safety requirements
EN 61326-1: 2006
EN 61010-1: 2010 (Pollution degree 2, overvoltage category II)
CONTROL
Control type Single set-point and alarm control
Control algorithm
A/D converter
Sampling time
Proportional band
Control period
Hysteresis
Output power
Adjustable between 0 and 100 . If Pb=0 , On-Off control is selected.% % %
and 250 secondsAdjustable between 1
1 and 50Adjustable between °C/F
The ratio of power at a set point can be adjusted between 0 and 100% %
HOUSING
Housing type Suitable for flush-panel mounting according to DIN 43 700.
Dimensions W77xH35xD71mm
Weight Approx. 200g (after packing)
Self extinguishing plastics.
Enclosure material
While cleaning the device, solvents (thinner, benzine, acid etc.) or must not be used.corrosive materials
Read this document carefully before using this device. The guarantee will be expired by
damaging of the device if you don't attend to the directions in the user manual. Also we don't
accept any compensations for personal injury, material damage or capital disadvantages.
R : 250V AC, 16A (for resistive load), Selectable as NO Control or Alarm2 output.elay
ET -E2011
1./4
english
up to date: 01022014, modification reserved and can be change any time previous notice !

SET SET
C.s.lo.= Control set point lower limit.(for selected output) Adjustable between 0 and C.s.Hi.
C.s.Hi.= Control setpoint upper limit.(for selected output)
Adjustable between and Upper scaleC.s.Lo.
a2.s.l= Alarm2 set value lower limit. Adjustable between 0 and A2.S.H parameter value.
a2.s.H= Alarm2 set value upper limit. Adjustable between parameter value and upper scale value.
A2.S.L
a2.Hy=
.
Hysteresis of the Alarm2
output
A2.st. = The state of Alarm2 output.
If A2 output is above the set
value. (on) Hi= lo= If A2 output is above the set
A2.Er. =
2 output is probe failure (on).
State of Alarm2 output in the
case of sensor failure.
= Aon
A2.tp indE.
= Function of Alarm type.
Four kinds of functions can be selected.
= alarm
(Independent)
= Deviation
= Band alarm (Band)
2
Independdnt
dE. bAnd
inp.t.
c.cn.
=
= J type , = K type = T
type =S type , = R type thermocouple selection.
This parameter varies when changing
Input type selection.
FE.cn. nc.nA.
p10.r. P13.r.
Unit = The temperature unit.
C°= °C, = °F
(This parameter varies when
°F
C.o.sE = Control output selection C-A2 SSR
= C/A2 (Relay) output selection
= SSR output selection
F.kE.C. = Function key setting parameter nonE manu.
= Function key is off.
= The function key with 2.set value is used.
= Manual mode can be achieved with the
function key.
= Only the temperature display mode is
C2.S.A. dSP.o.
C. Pb C. Pb
=
%0 %100
= %0 On-Off
Proportional band.(for selected
output) Adjustable between .0 and .0.
.0, control is selected.
C. ti C. ti
C. Pb
=
=
Integral time.(for selected output)
Adjustable between 0 and 100.0 minutes.
0.0,integral impact is disable.
parameter is different from “0”,this
C.Hys = Hysteresis of the output.(for selected output)
Adjustable between 1 and 50 °C.
C. td C. td
=
=
Derivative time.(for selected output)
Asjustable between 0.00 and 25.00 minutes.
0.0, derivative time is disable.
parameter is different from”0”,thisC. Pb
C. Ct.
C. Pb
= Period time.(for selected output)
Adjustable between 1 and 250 second.
parameter is different is different
C.p.st = The ratio of output power at the setpoint.Adjustable between %0 and %100.
C.E.P.s.= The percentage of faulty sensor
selected output power.Adjustable between %0 and %100.
C.typ. = Control output type C.typ.
typ
= =
HEAt CooL
means heatign control.
means cooling control.C. .
While the parameter names appear,if and keys are pressed together, returns to the program mode.
S.Cod =
.
Security menu access
code It should be 2011.
Cosc. CoN.o. nonE P.yEs
=
=
=
Parameters of
menu security access level code.
Invisible.
Modification can be done.
m.SEt. = This parameter allows manual adjustment of the output power when the manual output selection.
The percentage of manual output parameter.
Adjustable between %0 and %100.
If parameter is different
from C-A2,this parameter is seen.
co.SE
a.2.sc. al2.o. nonE P.yEs
=
=
=
Parameters of
menu security access level code.
Invisible.
Modification can be done.
Co.sc. Conf. nonE P.yEs P. no
=
=
=
Parameters of
menu security access level code.
Invisible.
Modification can be done.
= Only visible.
S.t.Sc. = men
=
Parameters of
u security access level code.
Invisible.
S.tun.
nonE
Co.sc. Conf. no yEs
=
m
=
=
Parameters of
enu security access level code.
Parameter settings are not
change.
Parameter setting will be
C.s.Lo.
C.s.Hi.
C. pb
C. ti
C. td
C.p.st
C.Hys
C. Ct.
C.typ
s.s.t.s.
C.E.p.s.
Con.o. AL2.o. ConF. S.tun. SEcu.
S.Cod.
Co.sc.
m.SEt.
a.2.sc.
Cn.sc.
S.t.sc.
dEF.P.
inp.t.
Unit
fltr.
C.o.sE
offs.
s.t.Co.
F.k.E.C.
A2.S.L
A2.S.H A2.HY A2.tP A2.St. A2.Er.
SET SET SET SET SET
F
Programming mode
This parameter indicates the time to reach set point value when the device is first enegised. Adjustable between 0 and 250 minutes. If 0 is selected, soft start feature will be enable and the device reaches set point value quickly.
Pb = 0, so start feature will be disable.Setting ft
Sst.S =Sofy starter timer set value
fLtr.= Coefficient of digital filter. Filter for display value. Adjustable between 1 and . If this parameter is 1,
digital filter runs most quick. If the parameter is , the filter run most slow. The value of parameter should be increased in interference.
200
200
oFfS. = Offset value. Offset value is added to the measurement value. Adjusted between -100 and +100°C.The normal value is 0.
St.Cu = Self tune control parameter.
If both keys are pressed , message is displayed on the screen and self tune process is started automatically. If both keys are pressed, message is displayed on the screen and self tune process is stopped.
yes
no
Selt tune begins when the measurement,
and measurement value
are shown alternately.Self tune process
completed automatically after the parameter is done no and is entered to the working mode. Self tune process begin when
the measured temperature is expected fall
below 90% of the set value the display shows
message alternately.Expected to fall
below the temperature set point 60% evolved
and then self tune process starts automatically. If asked to abort the self tune process, parameter is done and key is pressed.
PIdt.
te.HI
St.Co
message
stco
no
SET
If key is pressed while holding key, the programming mode is enabled.
SET
F
Entering from the programming mode to the run mode: If no key is pressed within 20 seconds during programming mode, the data is stored automatically and the run mode is entered. Alternatively, the same function occurs first pressing key and key is pressing programming mode is entered.Then and keys are pressing together,data is recorded and running mode is entered.
Modification Of Parameter Diagram
When holding key, the value of parameter flashes and using
keys the requested value can be adjusted.
If key is pressed and held 0.6 seconds, the value of the selected parameter changes rapidly. If waited enough,the value increases 100 at each step. After 1 second following the release of the key, initial condition is returned.The same procedure is valid for the decrement key.
Chys 656
SET SET SET
SET
C.s.lO.inp.t.
A2.s.l Co.sc.
C1.sE.
C.s.Hi.Unit
A2.s.H A2.Sc.
C2.SE.
C. PB Fltr.
A2Hy. Cn.Sc.
A2.SE.
C.HyS C.o.SE.
A2.tp S.t.Sc.
C. ti offs.
a2.st. dEf.P.
C. td f.k.E.C.
a2.Er.
a2.Er.
C. Ct.m.sEt. C.P.St. C.EP.S. S.s.t.S. C.typ.
TC input TC input TC input
TC input TC input
Pt100 input Pt100 input Pt100 input
Pt100 input Pt100 input
0
FE.cn.
0
025
2
2C-A2
indE P.yEs
P.yEs
400
P.yEs
400
P.yEs
500
4.0 0
Hi no
1.00 nonE
on
no
20 50
0 0 0
HEat
-200 Pt.
-200
600 °C
600
DEFAULT PARAMETERS
Set parameters Control output
parameters
Alarm2 output
parameters
Configuration
parameters
Self tune parameters
Security parameters
SET SET
2/4 ET -E2011

SET
°C
SET
ET2011
ENDA
°F C/A2 SSR
F
TERMS
mm12
( 1 ) )
Paramet (Progra )
Measurement value and set value indicator Running mode
er name and value mming mode
( ) ( rogram )
If only this key is pressed in normal operation,software version
number is seen. parameter processing
2 Value increment key P ming mode
(F.k.E.C. )
( )
( rogram )
2 Value decrement and parameter selection key.
P ming mode
( ) ( )
Paramet (Program )
4 Control ve Alarm set selection key Running mode
er set key ming mode
7 4 LED displaysegment, digits red
Mikro switch
, Alarm1 SSRFor control and outputs 3 digits red LED
MODIFICATION OF CONTROL AND ALARM SET POINTS
ERROR MESSAGES
Character heights
( ),( ),( )2 3 4 Keypad
( )5 State indicator
ALARM2 OUTPUT TYPES
Independent Alarm
A2.tp. indE==
Deviation Alarm
A2.tp dE.
Band
=
Alarm
A2.tp. bAnd
=
Band Alarm With Inhibition
A2.tp. bAn.i
A2.St. Hi=
A2.St. lo=
=A1.St. Lo
=A2.St. Hi
ASV
SV SV
SV
SV+ASV
SV+ASV
SV-ASV
OFF OFF
OFF
OFF OFF
OFF
-300
300
+300
300
ON ON
ON
ON ON
ON
ON ON
OFF OFF
Beginning
SV = ASV = (ASV min. = 0, ASV maks. = 300 )Set point of CONT output Set point of AL2 output
SV = ASV =Set point of CONT output Set point of alarm output
(ASV min. =-300, ASV ma . = +300)x
(ASV min. = 0, ASV ma = +300)X.
(ASV min. =
ASV ma = )
beginning of scale
x. end of scale SV = ASV =Set point of CONT output Set point of AL2 output
Band alarm is possible Band alarm is possible
Beginning
SV SV
SV+ASV SV+ASV
SV-ASV SV-ASV
a2,Hy A2.Hy
A2.Hy
A2.Hy
SET
( 1 ) PV and SV display
( )5
3 seconds later
3 seconds later
3 seconds later
3 seconds later
250
pfa
psC
____
C1.SE.
C2.SE.
a2.SE.
400
398
500
399
399
499
SET
C.O.SE.parameter is set to the output of SSR,this
parameter is seen.
Sensor is broken
Pt100 sensor is short circuit
Temperature value is
higher than the value
Temperature value is
lower than the scale
parameter, is set to the parameter,this
parameter is displayed.
F.kE.C. C2.S.A.
----
ET -E2011
3./4

5
6
SUPPLY:
NOTE :
184-253V AC
50/60Hz 5VA
Phase
Neutral
230V AC
Supply
Switch
Cable size: 1,5mm²
Fuse
F 100 mA
250V AC
Fuse should
be connected.
Order Code 2011-X XXX- X: ET -
Supply voltage
230 ... 230V AC
24 ........24V AC
VAC ...
110VAC......110V AC
0 VAC
SM.......9-30VDC/7-24V AC
Contact current selection
....
None......8A contact output
P 16A contact output
Input selection
....
RT....PT100 input
T TC input
CONNECTION DIAGRAM
ENDA ET2011 is intended for installation in control panels. Make sure that the device is used only for intended
purpose. The shielding must be grounded on the instrument side. During an installation, all of the cables that are
connected to the device must be free of energy. The device must be protected against inadmissible humidity,
vibrations, severe soiling.Make sure that the operation temperature is not exceeded. All input and output lines
that are not connected to the supply network must be laid out as shielded and twisted cables. These cables should
not be close to the power cables or components. The installation and electrical connections must be carried on by
a qualified staff and must be according to the relevant locally applicable regulations.
1) Mains supply cords shall meet the requirements
of IEC 60227 or IEC 60245.
2) In accordance with the safety regulations, the
power supply switch shall bring the identification of
the relevant instrument and it should be easily
accessible by the operator.
Note
Holding screw
0.4-0.5Nm
Equipment is protected throughout
by DOUBLE INSULATION.
35mm
77mm
SET
°C
SET
ET2011
ENDA
°F C/A2 SSR
F
Flush
mounting
clamp
71mm
29,5mm
Panel cut-out
1
Flush mounting
clamp Panel
2
73mm 5mm
Depth
Connection
cable
8680407711246
1 2 3 4 5 6 78910
ENDA INDUSTRIAL ELECTRONICS
SN: XXXXXXXXX
ET20 1-T-230
PID DIGITAL THERMOSTAT
1
230V AC +10% -20%
50/60Hz 5VA
11 12
C/A2
250V AC 8A
RESISTIVE LOAD
TC
+
-
-
+
SSR OUT
MADE IN TURKEY
DIMENSIONS
Note
1) Panel thickness should be maximum 7mm.
2) If there is no 60mm free space at back side of the device,
it would be difficult to remove it from the panel.
the panel:
-While pressing both side of
the device in direction , push it1
in direction 2.
For removing the device from
8 6 8 0 4 0 7 7 1 1 2 4 6
8 6 8 0 4 0 7 7 1 1 2 8 4
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
ENDA INDUSTRIAL ELECTRONICS
ENDA INDUSTRIAL ELECTRONICS
SN: XXXXXXXXX
SN: XXXXXXXXX
ET20 1-T-230
PID DIGITAL THERMOSTAT
1
ET20 1-T-230-P
PID DIGITAL THERMOSTAT
1
230V AC +10% -20%
50/60Hz 5VA
230V AC +10% -20%
50/60Hz 5VA
11
11
12
12
C/A2
250V AC 8A
RESISTIVE LOAD
C/A2
250V AC 16A
RESISTIVE LOAD
TC
TC
++
-
-
-
-
++
SSR OUT
SSR OUT
8 6 8 0 4 0 7 7 1 1 3 2 1
1 2 3 4 5 6 7 8 9 10
ENDA INDUSTRIAL ELECTRONICS
SN: XXXXXXXXX
ET20 1-RT-230
PID DIGITAL THERMOSTAT
1
230V AC +10% -20%
50/60Hz 5VA
11 12
C/A2
250V AC 8A
RESISTIVE LOAD
-
+
SSR OUT
PT100
8 6 8 0 4 0 7 7 1 1 3 6 9
PT100
1 2 3 4 5 6 78910
ENDA INDUSTRIAL ELECTRONICS
SN: XXXXXXXXX
ET20 1-RT-230-P
PID DIGITAL THERMOSTAT
1
230V AC +10% -20%
50/60Hz 5VA
11 12
C/A2
250V AC 16A
RESISTIVE LOAD
-
+
SSR OUT
E-mail : [email protected]
Internet : www.suran-elektronik.de
Tel.: [phone] / 625 617
Fax: [phone]
SURAN Industrieelektronik
Dettinger Str. 9 / D-72160 Horb a.N ET -E2011
4./4