ENDIAN 4i Edge 313 User manual

4i Edge 313 Quick Start
www.endian.com
What You Have and What You Need
With your 4i Edge box you receive:
• 4i Edge 313
• 5 pin terminal block for digital I/O
• 2 pin terminal block for power input
To install your 4i Edge 313 and protect your network you need:
• 24V DC power socket
• Ethernet switch (connected to your network)
• DIN rails
• Maximum surrounding air temperature 60 °C
Hardware Installation
1. Place your 4i Edge 313 on a steady surface or attach it to the DIN rail
2. Connect Ethernet port 1 of your 4i Edge 313 to your switch using a standard
patch cable (or a crossover patch cable for a direct connection to the Ether-
net interface of your PC)
Warning! The default IP address of the unit ’s GREEN interface is
192.168.0.15. Make sure there is no other machine with this address in
your network; should you have such a machine, turn it off or disconnect it
from the switch during the installation and initial configuration of the unit.
3. Connect the DC power socket to the unit. The front view of the terminal block
connector is shown here.
Terminal Block: 105°C suitable
for 12-30AWG wire size,torque
value 5-7 lb-in.
Web Interface
1. Configure your PC Ethernet interface with an IP address belonging to the
192.168.0.0/24 subnet that is different from 192.168.0.15 (Endian IP
address)
2. Open your Internet browser (e.g. Mozilla Firefox) and go to address
192.168.0.15
• The system will redirect you to https://192.168.0.15:10443/ and ask you
for your preferred language and your time zone. After that you need to
accept the license agreement.
• The system will now ask you to choose 2 passwords (admin for web
interface and root for console).
Ethernet
10/100/1000 (RJ-45) Ports
24V Power Input
Power LED
Reset Switch
Status LED
Digital Input LED
Digital Output LED
COM LED
SIM LED
Choose Your Internet Connection Mode
Now it is time to configure your Internet connection:
1. Choose your network mode
• Routed: if you want to use the appliance as router in your network
• Bridged: if you want your appliance to act transparently with-
out having to change the existing network infrastructure
• No uplink: if the appliance should not act as a router but
require clients to address it directly
2. When choosing routed mode the uplink type must be specified:
• Ethernet static
• Ethernet DHCP
• PPPoE
• Analog/UMTS modem
Network Settings
1. Every network “area” is assigned to a color:
• GREEN local network (LAN). This is the safe area where your
trusted computers are.
• RED external network (WAN). Usually this is the interface connect-
ed to the Internet.
• BLUE wireless network. It is suggested to place the computers that
use wireless connections in this area. This kind of network is usually
not as safe as a wired one.
• ORANGE network for servers connected to the Internet (DMZ).
It is meant for systems that have to provide services to external
networks. This way, even if the security of one of these servers has
been compromised, the GREEN area will remain safe.
2. You can configure the appliance’s Ethernet ports to your liking by
assigning them to the respective zones. Follow all the wizard steps
to configure the appliance and protect your network. Follow all the
wizard steps to configure the appliance and protect your network.
This is how the Ethernet ports are mapped to device names in the
setup wizard:
Ethernet port Wizard device name
Ethernet 1 lan1
Ethernet 2 lan2
WAN eth1
Rail Mounting
Earthing
Ground Terminal
SIM Card Slot
USB Port
Digital I/O Ports
COM Port
For use in Pollution Degree 2 Environment.
CAUTION: FOR USE IN A CONTROLLED ENVIRONMENT.
ATTENTION: EN CAS D’UTILISATION EN ATMOSPHÈRE CONTROLÉE.

4i Edge 313 Quick Start
www.endian.com
Endian Network Account
To activate your Endian Network subscription and keep your appliance
always up-to-date with the latest features and security updates follow these
steps:
A. You already have an Endian Network account
1. When the system asks you if you have an Endian Network account
choose “yes” and go to the next step.
2. Now fill in the form using your data and the activation code on the
back of this page.
B. You do not have an Endian Network account
1. When the system asks you if you have an Endian Network account
choose “no” and go to the next step.
2. Click on the “Endian Network account” link and insert the activa-
tion code on the back of this page.
3. Fill in the registration form and create your account.
4. Close the registration window and go to the next step.
5. Now fill in the form using your data and the activation code.
Your Endian appliance is now ready!
Mapping Table for Reference
COM Port
1 5
8 6
Pin RS232 RS485 RS422
1 - A- TX-
2 RXD A+ TX+
3 TXD - RX+
4 - - RX-
5 GND GND GND
6 - - -
7RTS - -
8 CTS - -
9 - - -
Digital I/O
1
5
Pin REF Description
1DO_GND
Output digital signal
(0V ground) connected
to the emitter of the
transistor
2 DO
Output digital signal
connected to the
drain of the MOSFET
transistor
3 DO_VDC
Common of the exo-
thermal predrive pow-
er supply (between
+12 et +24 VDC)
4 DI_GND Ground of the input
(isolated)
5 DI Input digital signal
DIN-Rail Mounting
The metal DIN-rail kit is fixed to the rear panel of the 4i Edge 313.
After opening the product box, mount the 4i Edge 313 on corrosion-free
mounting rails that meet the EN 60715 standard.
Installation
Step 1: Insert the upper lip of the DIN-rail into the DIN-rail mounting kit.
Step 2: Press the 4i Edge 313 toward the DIN-rail until it snaps into
place.
Din-Rail
Removal
Step 1: Gently pushed up from the bottom of the 4i Edge 313.
Step 2: Slightly pull the 4i Edge 313 forward and lift up to remove
from the DIN-rail.
Din-Rail
4i Edge 313
Quick Start